137353300â Frigidaire Washer âLidâ Lock Switch is âan electromechanical⣠lid-lock/interlock assembly used⢠on Frigidaire top-load washers;⤠it⤠combines aâ mechanical latch wihtâ one or more electrical⣠contacts or sensors that indicate whether the lid is closed and⢠mechanically secured. As a discrete service part it is indeed mounted⣠to the washer cabinet and engages with a⤠strikerâ orâ latch on the⤠lid, âproviding both a âphysical⤠lock and an electrical âsignal âto the machine âcontrol system.
Inside âthe appliance the lid âlock switch serves as a âsafety interlock and âŁa control input: it prevents⣠theâ washer from enteringâ high-speed spin or agitation when the lid is open and it signals the main control board that the lid isâ properly closed and latched. The component interfaces directlyâ with âthe washer’s control module and drive systems,⤠and is âpart âof â¤the safety and sequencing circuits that coordinate door position, motor â¤operationand cycle progression. Electrical â˘contacts inâ the âassembly change state when the âlatch is âengagedand some designs also âinclude a solenoid⤠or actuator to retain the lid during⣠certain cycle phases.
In this article â˘you will â¤find a technical overview of the 137353300 Frigidaire â˘Washer⣠Lid Lock Switch covering its intended function, typical âmodel compatibility, common failure symptoms (for exmaple, lid lock error codes, washer not starting, noâ spin or intermittent lock behavior)and diagnostic approaches technicians and learned owners can use. â¤The piece will also discuss replacement considerations such as verifying part crossâreference numbers, connector and mounting compatibility, basic âcontinuity checksand safety precautions to observe during âŁremoval and installation.
Table of Contents
- Function⢠and Safety Role of the lid Lock Switchâ in âFrigidaireâ Washâ Cycle Control
- How the 137353300 Frigidaire Washer âLid Lock Switch Interfaces with the Control Boardâ and Mechanical Latch
- Common Failure Symptoms and Diagnostic â˘Indicators for Lidâ Lock Switch Faults
- Replacement Considerations, Model Compatibilityand StepâbyâStep Installation Procedure for the Lid Lock⣠switch
- Q&A
- Future Outlook
Function and Safety Role ofâ the Lid Lock â¤Switch in Frigidaire Washâ Cycle Control
The 137353300 Frigidaire âWasher Lidâ Lock Switch⣠is a⢠combined mechanical latch and âelectrical interlock used in many Frigidaire top-load machines to provide⤠a definitive â”lid closed/locked” signal to the electronic control board. As a safetyâ interlock, the assembly prevents the washer âfrom entering high-speed âspin or agitation states until the lid is fully âengaged and⢠theâ lock actuator has â˘completed its âŁtravel.⣠The switch contains one or more microswitch contacts actuatedâ by aâ solenoid âor âcam mechanism; when the control board â˘commands a âlocked state it applies voltage to the actuator, the âlatch engagesandâ the⣠microswitches change⢠state to allow subsequent cycle steps â˘such â¤as drainage and motor run commands.
Failure âŁmodes of the lid lock âswitch typically affect cycle continuity â¤andâ machine safety rather than⤠core âmechanical âdrive components, so âdiagnostics focus on electrical continuity, â¤proper actuator movementand âŁconnector/harness integrity. Common practical checks include listening for the lock “click” âat cycle start, verifying continuity âof the switch contacts with a multimeter when the âŁlatch is manually engagedand confirming âŁthe â¤control board is supplyingâ the expected drive signal to theâ actuator. â¤as this part â¤is used â˘on specific Frigidaire model families, technicians should match⤠the â˘appliance model number âandâ connector configuration before replacing the unit;â after replacement, verify⣠mechanical alignmentâ and âperform a run test to confirmâ the control boardâ recognizes the locked state.
- Symptoms:⢠washer will âŁnot âstart,will⤠not advance to spin,stops mid-cycle,or displays lid-related error codes.
- Inspection points: audible actuation, continuity âŁof microswitch contacts, connector pins⣠for corrosion âor damage.
- Replacement considerations:⤠match part number, harness connector, âŁand mounting orientation; âŁtest with a diagnostic cycle after âŁinstall.
| Item | Description |
|---|---|
| Function | Provides a locked/closed â¤status signal⢠to the control board and physically secures the âlid during critical cycle phases. |
| Diagnostic check | Listen for actuation, confirm control-board drive to the actuatorand measureâ continuity of switch contacts when latched. |
| Compatibility | used onâ select Frigidaire top-load washers; verify appliance model andâ connector type match before installing replacement. |
How⤠the 137353300 Frigidaire Washerâ Lid Lock Switch Interfaces with the Control Board âand Mechanical â¤Latch
The 137353300 âŁFrigidaire⣠Washer Lid Lock Switch is a combined mechanical and electrical interlock that tells⤠the washerâ control board when⢠the lid is âsecurely latched and permits drive and⤠high-energy functions onlyâ after confirmation. Mechanically, the part â˘integrates a small latch â˘that physically engages the âlid; electrically, it provides one or more switch contacts or â¤low-voltage sensor lines to the main control board.During a wash cycle the control board applies⤠a lock command (energize or expect a closed circuit), the latch moves to its â¤locked position and⣠theâ switch⣠changes state to return a âlockedâ signal. That confirmation âsignal is used by the controller to âenable motor⤠start, heater operation, door-unlock timing, âand to prevent the lock from opening under centrifugalâ force or during high-speed spin.
- symptoms of a failedâ switch: lid-lock error codes, âwasher will not startor âspin â˘begins then stops â˘when the lid appears âlocked.
- Practical testâ steps: verify âconnector fit, check for continuity between switch terminals when âthe⢠latch⣠is engaged,â and check for the expected control-board⣠command voltage during a lock cycle.
- Compatibility ânote: â˘replacement âmust match theâ harness connector and the switch logic (closed vs. open when locked) used byâ the specific washer model.
| Item | Description |
|---|---|
| Electrical interface | Typically a low-voltage DC sense/ground â¤pair or a smallâ multi-pinâ connector âthat provides a lock-actuate line âand a lock-status return âto the control board. |
| Mechanical function | Latch engagesâ the lid and moves a⢠microswitch or sensor element; physical engagement ensures a positive⤠switch state âfor the âŁcontroller. |
| Basic test | With the lidâ depressed into the locked position, measureâ continuity or âthe expected logic voltage on the status â¤pins to confirm the switch changes state correctly. |
For technicians, the useful diagnostic sequence âŁis: visually inspectâ the âŁlatch and connector, command a lockâ cycle from the control board and⤠observe â˘whether the latch moves, â˘then measure âthe switch contacts â¤or status line.⣠If the latch moves but⣠theâ controller dose not see the locked signal, the issue is usually the switch âcontacts or wiring; if the switch reportsâ locked but the latch does not move, the actuator portion or â˘its âdrive circuit may be at fault. Replacing the 137353300 Frigidaire⤠Washer Lid Lock Switch with a part that matches the connector, terminal assignment, âand signal polarity resolves mismatches that or else result in intermittent lock behavior or persistent error⣠codes.
Common Failure Symptoms and Diagnostic Indicators â¤for Lid Lock Switch Faults
The 137353300 Frigidaire Washer â¤Lid Lock Switch mechanically secures the lid â¤and provides the interlock signal ârequired by the control board to allow fill, agitation,â and spin. Internally thisâ component combines a mechanical latch with one or more electricalâ contacts; when the latch âis driven into the locked position the contacts change state to âtell the controller the â˘lid is âsecure. âCompatibility is persistent by mounting geometry, connector pinoutand â¤actuation method, so replacement units â¤must match the harnessâ and screw locations â¤for âthe specific Frigidaireâ model to âŁensure correct engagement and âreliable signaling â˘to the machine’s control electronics.
- Washer will not start or will stop mid-cycle and the lock â˘LEDâ or status âlights blink in a pattern associated with a door/lid fault.
- Control attempts to engage âthe lock (audible click of theâ actuator) but the latch does not move or⣠fails to hold theâ lid closed.
- Intermittent operation: cycles completeâ only when the lid is closed âand pressed firmly, indicating worn â˘latch or loose connector.
- Multimeter⤠continuity: no continuityâ when the latch is physically closed (orâ opposite to expected state) indicating âcontact â˘failure.
- Voltage present at the⣠connector during a lock command but no mechanicalâ movement suggests a seized â˘actuator â˘or broken linkage; â¤absence of voltage points to âwiring or control board failure.
- Visible damage: heat-melted plastic,burnt âterminals,or excessive corrosion at the connector that⢠can produce open or intermittent circuits.
| Item | Description |
|---|---|
| Continuityâ check | With lid inâ the locked position the switch contacts should change state; use an ohmmeter to verify continuity aligns with the service manual expected behavior. |
| actuation signal | Measure the controlâ board output at the lock connector during the start sequence; â˘presence of a drive⤠signal with no mechanical response âindicates â˘a âŁfailed â˘actuator or linkage. |
| Fit & âŁconnector | Ensure replacement matches physical mounting and⤠wiring; incorrect connector âpinout or latch â¤geometry prevents proper interlock â¤operation. |
For practical diagnosis,observe the machine during a start attempt: listen for the actuator,check⢠for lid movement,then measure electrical behavior at the harness. If continuity and mechanical operation are correct but no drive signal appears, trace wiring back to the control board or consult theâ model’s wiring diagram; âif the âcontrol provides voltage butâ the⤠latch does not engage, â˘replacement of the lid lockâ assembly is âthe normal next step. Avoid permanently bypassing the interlock for normal â˘operation-temporary bypassing might â¤potentially â˘be used only forâ a controlled functional test and âshould be followed by a proper replacement â¤to restore the required safety interlock.
Replacement considerations, Modelâ compatibilityand StepâbyâStep Installation Procedure for âthe Lid Lock âSwitch
The â137353300 Frigidaire Washer Lid Lock Switchâ is âan electromechanical âinterlock designed to both detect lid âposition and prevent the lid from opening âŁduringâ critical⤠cycles.The âassembly âtypically⣠integrates one or more microswitches and aâ mechanical latch⢠or⣠solenoid so âthe control board receives a definitive closed/open signalâ and the â¤lid remains physically secured during high-speed â¤spin. Failure modesâ include an open circuit in âthe switch â(no continuity when the latch is âŁengaged), mechanical wear that prevents the latch from seating,â or⣠connector pinout mismatch; thes failures commonly present as a washer that⤠will notâ advance to spin, a âstalled cycleor aâ lid-related error code on the control panel.
Confirm compatibility by matching the OEM number, harness connector style, mounting tabs, âand the control-circuit logic before installing a replacement;â visually similar parts can have âŁdifferent pinouts or actuation directions. For a reliable repair, first remove âpower âto theâ appliance and verify the existing switch behavior with a multimeter (check continuity with the lid actuated and⢠released).â Reassembly requires correct orientation so the actuator on the lid properly engages the switch during closureand a⣠brief functional test (verify⤠lid-lock engages, continuity â˘closesand the washer will initiate spin) should be performed before full reassembly.
- Safety first: disconnect mains power and confirm with a meter.
- Remove access⢠panels to reach the lock; ânote screw locations and harness routing.
- Unplug the harness and remove mounting fasteners, then swap the switch assembly.
- Bench-test âcontinuity with âthe lid⢠actuator engaged â¤and confirm proper mechanical engagement after â¤installation.
- Reassemble panels and⣠run aâ diagnostic or short cycle to verify lockâ function and that no⤠lid âerror codes appear.
| Item | Description |
|---|---|
| Part ânumber | 137353300 Frigidaire washer Lid Lock Switch |
| Function | Mechanical latch and electrical interlock that signals the control board and secures the lid during⣠wash/spin cycles |
| Connector | Typically a 2-3 pin wiringâ harness; verify shape and pin count against the original |
| Electrical | Control-circuit âlevel signaling; verify⣠actual voltages in the service manual for⣠the specific model |
| Mounting | Screw or snap-mounted to lid âor cabinetâ frame; orientation affects actuation â˘and must match original |
Q&A
What isâ the 137353300 Frigidaire washer lid lockâ switch and what âdoes it do?
The 137353300 is the lid/door lock switch assembly used on certain Frigidaire topâ and frontâload washers. It physically locks the lid âduring specific cycleâ phases (usually spin and highâspeed agitation) and sends⢠a signal to the control board⢠that the⣠lid is⢠closedâ and secured so the washer⤠can continue its cycle. it is a safety â¤interlockâ to prevent the machine from running with the lid open.
What are the common symptoms of a failing lid lock switch?
Typical symptoms include the âwasher not starting or not advancingâ past the fill/rinse steps, failing to spin or âŁagitate at⤠full⤠speed, an intermittently locked or unlocked lid, the lid not latching properlyor the washer displaying âa âdoor/lid lock error (check yoru model’s⤠code list). You â˘may also hear the⣠lockâ attempt to engage but failor the machine â˘may refuse to start âwhen⢠the âŁlid is⢠closed.
How can I test the 137353300 lid lock switch to⣠see if â¤it’s âŁbad?
first disconnect powerâ to the âŁwasher.Access the lock assembly and disconnect âŁits â˘wiring harness. Using a⢠multimeter set â˘to the continuity or resistance (ohms) range, check for continuity between the â¤switch terminals while manually actuating the latch (openâ vs closed positions). A workingâ switch will change state â(openâ to âclosedâ or viceâ versa) when actuated. Also inspectâ the connector and⤠wiring âfor burnsâ or corrosion. If the switch does not change â¤state or shows infinite resistance when⣠itâ should be closed, it is indeed likely faulty.
How do I⤠replace the 137353300 lidâ lock⢠switch?
Always unplug â¤the washer before starting. Access the switch by â¤opening the âŁtop panel or control console per your model’s service instructions (often requires removing a few âscrews at the back andâ sliding⢠the âŁtop forward). Unplug the switch harness, remove retaining screwsâ or clips, note the orientation of the actuator/latch,â and âswap â¤in âŁthe new 137353300. Reconnect the harness, reassembleâ panels, âŁrestore âpowerand test â¤a cycle. âTake pictures during disassembly to ensure correct reassembly and follow any⤠modelâspecific steps in the service manual.
How do I no if â137353300 is compatible with my washer model?
Check the washer’s â˘model number (usually on a âŁtag behind the door, on the cabinetor under the lid) and⣠use Frigidaire’s⤠parts lookup or aâ trusted parts retailer to confirm compatibility with partâ 137353300. âŁCrossâreference the part number in the official parts⤠diagram âfor your exact⤠model. â¤If you’re unsure, âŁprovide⤠the âwasher model⣠number to the parts⢠supplier⤠or âtechnician to⣠verify fit and function before ordering.
Can I run the washer with a faulty lid lock switch?
Running the washer with a faulty lid lock is not recommended. âthe lock is a âsafetyâ device and mostâ modern washers willâ prevent certain operations (especially â¤spin) if the control does not detect a locked lid. Attempting to bypass the lock or running the washer with a known defect can be unsafe âŁand âŁmay void warranties.Repair âorâ replace the switch before using the machine for normal cycles.
After replacing the lid â˘lock switch, do I need to reset âthe washer?
Often no formal calibration is required. In âŁmany cases simply restoringâ power will allow the machine to â˘recognize the new switch. If the washer shows an error code after replacement,⣠try a âsimple â˘power cycle (unplugâ or switch off power for 1-5 â˘minutes, then restore). If the error persists, consultâ the model’s service manual for diagnostic/reset procedures or run â˘a âdiagnostic/service⢠mode to clear codes if applicable.
What other⢠components can cause the same symptomsâ as a bad lid lock switch?
Similar symptoms can come from a damaged âlid strike/actuator (the part on the⣠lid that engages the lock), a faulty wiring harness or connector, a defective control board that is not reading the switch signalor mechanical issues â¤withâ the lid hinges or latch alignment. Always inspect the latch mechanism,⤠connectorsand wiring for physical damage and â¤test the switch electrical behavior â˘before âreplacingâ the âcontrol board.
Future Outlook
The â˘137353300â Frigidaire âWasher Lid Lock Switch serves a critical role in modern washers by securing⢠the lid âduring operation, communicating the lid-locked status to the control board,⢠and helping prevent accidental interruptions,â water spillageor injury. As a safety and operational component, a functioning⣠lid âlock switch ensures â¤that â¤wash and spin â¤cycles⣠complete correctly and that the machine’s diagnostic âsystems can accurately⣠detect and respond to fault conditions.
As a faulty lid lock switch can produce symptoms âŁranging from error codes and unresponsive âŁcycles to âunsafe operation, proper diagnosis âand timely replacement are critically important. Verification should include visual inspection, electrical testingand review of diagnostic⢠codes or âmanufacturer guidance⤠to confirm the switch is theâ root âcause. When replacement is necessary,using the correct 137353300 Frigidaire Washer âLid Lock Switchâ or an âequivalent OEM part and following recommended installation procedures-either by a⣠qualified technician or according to the manufacturer’s instructions-helps restore safe,reliable operation and prolong appliance life.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
