WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit is a flexible, metal-braided water-supply assembly intended too connect a household water source to a dishwasher inlet. As a plumbing connection component, it consists of a braided outer jacket over an inner water-carrying tube and factory-fit end fittings; its 6-foot length provides extended reach to accommodate cabinet layouts and service access. the assembly is a replaceable service part commonly supplied as an OEM connection kit for GE dishwashers but follows the same functional design used across many brands.
Inside the appliance system the connection kit serves as the conduit that delivers pressurized water from the shutoff valve to the dishwasher’s inlet valve or solenoid. It directly interfaces with the plumbing shutoff, external supply tubing, the dishwasher inlet fitting and, indirectly, with downstream elements such as the inlet solenoid, wash pump, float switchand any leak-detection devices or air-gap assemblies. Proper selection and installation of the hose affects flow rate, sealing integrity under pressure cycles, resistance to vibrationand the prevention of leaks that could trigger safety and control responses.
in this article you will learn the kit’s intended function and where it is typically installed,how to verify compatibility with inlet fittings and household plumbing,common failure modes and symptoms to watch for (such as visible leaks,bulging,loss of water pressure or intermittent filling),basic troubleshooting steps to isolate a supply-line issue,and practical replacement considerations such as matching connector types,verifying hose length and routing,torque and sealing practices,and inspection intervals to maintain safe operation. The goal is to provide technicians, engineers and appliance owners with the technical context needed to identify, test and replace the connection safely and correctly.
Table of Contents
- Function and Role of the Dishwasher Inlet Connection Hose: pressure Management, Fluid Transferand Safety Interfaces
- How the WX28X326 GE 6’ Metal Braided Dishwasher Connection Kit Works Inside the Appliance: internal Flow Path, sealsand Mechanical Integration
- Common Failure Symptoms of the Connection Kit: Leak Patterns, Pressure Irregularitiesand Braided Hose Degradation
- Compatibility, Replacement Considerations, and Installation Requirements for WX28X326 and Equivalent Dishwasher Models
- Q&A
- In Summary
Function and role of the Dishwasher Inlet Connection Hose: Pressure Management, Fluid Transferand Safety Interfaces
The WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit serves as the rigid, pressure-bearing link between a household water supply and a dishwasher inlet. In normal operation the hose must transmit steady static pressure and the rapid pressure pulses created by solenoid valves and the appliance’s fill system without leaking, kinkingor collapsing. The stainless-steel braid gives axial and hoop strength to resist abrasion and accidental crushing while the internal tubing carries the water; the hose assembly is thus a primary pressure boundary in the supply circuit and must match the appliance inlet and shutoff-valve fittings to maintain a reliable seal and proper flow.
- Construction: braided metal exterior over inner water tube for mechanical protection and flexibility
- Behavior: transmits static and dynamic pressures, tolerates occasional bending but not tight coils or sharp edges
- Compatibility considerations: confirm inlet/outlet thread or compression sizes and local backflow/anti-siphon requirements before installation
Pressure management with this connection kit is passive: it does not regulate pressure but must withstand the system pressure plus transient spikes from valve actuation. Installers should avoid undue axial strain and sharp bending radii, secure the hose to prevent movement during pump cyclesand torque fittings to manufacturer recommendations to prevent leaks. Inspect the hose periodically for external braid fraying, bulging of the inner tube, or seepage at joints; such symptoms indicate degradation and require replacement. In practical terms, replacing a deteriorated rubber line with a metal braided kit improves mechanical durability and reduces the likelihood of rupture, but does not eliminate the need for a properly sized shutoff valve, routine maintenance, or compliance with local plumbing codes.
| Item | Description |
|---|---|
| Length | 6 feet – provides additional reach for appliance positioning |
| Construction | Metal braided exterior over flexible inner tubing for strength and flexibility |
| Primary function | Fluid transfer and pressure containment between house supply and dishwasher inlet |
How the WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit Works Inside the Appliance: Internal Flow Path,Seals,and Mechanical Integration
The internal flow path of the WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit consists of a continuous inner waterway surrounded by a stainless-steel braid that controls expansion and provides mechanical protection. Water enters the kit at the supply fitting, travels through the smooth inner liner and exits at the dishwasher inlet valve; the liner material and its internal diameter determine the hydraulic resistance and therefore the pressure drop across the length of the hose. Crimped ferrules or swaged terminations secure the liner to the end fittings so the flow path remains concentric under pressure, while the external braid limits radial expansion and protects the liner from abrasion where the hose is routed behind cabinetry.
Watertight integrity is achieved with sealing elements integrated into the end fittings-typically molded washers, O-ringsor compression-style ferrules at the appliance and shut‑off valve interfaces-and by proper mechanical integration to prevent torque or bending forces from stressing those seals. The braid and fitting geometry provide a degree of strain relief, transferring axial and torsional loads away from the inlet valve body; during installation technicians should route the hose to avoid tight bends or contact points that can concentrate fatigue. For example, replacing a deteriorated rubber line with this metal-braided kit restores a stable internal flow path while reducing the risk of pinch‑point failures, but installers should still verify each seal under pressure and re-tension fittings per the appliance manufacturer’s guidance.
- Inner liner: smooth low-friction waterway controlling flow and pressure drop
- Stainless braid: mechanical reinforcement and abrasion protection
- End fittings and seals: provide watertight interface to valve and shut-off
- Strain relief characteristics: limit stress on appliance inlet during movement
| Item | Description |
|---|---|
| Inner tube | Continuous liner that carries water and sets hydraulic resistance |
| Outer braid | Stainless-steel mesh that prevents expansion and protects the liner |
| Fittings & seals | Crimped/swaged terminations with washers or O-rings to ensure a leak-free connection |
Common Failure Symptoms of the Connection Kit: Leak Patterns, Pressure Irregularitiesand Braided Hose Degradation
the WX28X326 GE 6′ metal Braided Dishwasher Connection Kit functions as the flexible water supply between the household shutoff valve and the dishwasher inlet, combining an inner polymer liner with an external stainless-steel braid and crimped end fittings. typical compatibility covers standard dishwasher inlets and residential angle-stop valves, but technicians should verify thread type and compression style before installation.Failures that begin in the inner liner often present differently from failures at the fittings or the braid: inner liner degradation first reduces flow or causes intermittent pressure loss, while ferrule or nut loosening produces visible weeping at jointsand braid corrosion or fraying may expose the liner to abrasion and accelerate rupture.
Leak patterns and pressure irregularities provide diagnostic clues: slow drips at the connection usually indicate a seal or ferrule issue, isolated wet spots mid-hose point to micro-cracking of the linerand sudden high-volume leaks typically result from end-fitting separation or a full breach of the inner tube.Braided-hose degradation shows as external rusting, braid fray, bulging or soft spotsand extrusion of the liner through the braid; thes conditions correlate with rapid loss of serviceability and should prompt replacement rather than repair. practical checks include running a fill cycle while inspecting all fittings,feeling along the hose for soft or warm sections,and confirming consistent inlet pressure or flow at the shutoff valve; any of the symptoms below warrant immediate removal of the assembly and fitting-level inspection or replacement for safety and to prevent cabinet flooding.
- Weeping at fittings: indicates loose nut,damaged ferrule,or degraded seal.
- Pinhole leaks along hose: inner liner micro-cracks or abrasion through the braid.
- Bulging/soft spots: internal liner failure under pressure.
- Rusted or frayed braid: loss of mechanical protection and impending rupture.
- Intermittent low fill or hissing: pressure irregularity from partial blockage, kinkor liner collapse.
| Item | Description |
|---|---|
| Visible leak location | At fitting = seal/ferrule; mid-hose = liner breach; sudden flow = end-fitting failure. |
Compatibility, Replacement Considerationsand Installation Requirements for WX28X326 and Equivalent Dishwasher Models
The WX28X326 GE 6′ Metal Braided dishwasher Connection Kit functions as a flexible water supply between the household shutoff and the dishwasher fill valve, replacing rigid copper or deteriorated rubber tubing to reduce stress on connections and allow easier routing. In practice this kit’s braided outer jacket provides abrasion resistance and helps control kinking while the inner liner supplies potable water; however, compatibility depends on matching the appliance inlet and shutoff fittings. Verify the dishwasher inlet thread or compression size and the shutoff valve outlet type before installing or replacing an existing hose-many dishwashers use a small-diameter compression fitting on the appliance side, so adapters or different-end fittings may be required for a proper, leak-free connection.
- Verify fitting type and size (compression vs. threaded/NPT) and confirm whether an adapter is needed.
- Check material and pressure/temperature ratings on the kit versus the appliance and local plumbing requirements.
- Route to avoid sharp bends, secure to cabinet framing or strapsand keep the hose away from heat sources and moving parts.
- Do not use pipe dope on compression seats; apply thread sealant only to compatible threaded connections per manufacturer guidance.
Installation requires shutting off the water, relieving line pressureand making connections using the correct sealing method for the fitting type; after connection, inspect and test under normal household pressure and run a full fill/drain cycle to confirm no leaks. When selecting an equivalent replacement, prioritize equal or better construction (stainless-braided exterior, food-grade inner tube), matching end fittingsand equal or higher working-pressure and temperature ratings-replace hoses showing corrosion, bulging, frayingor persistent seepage rather than attempting repairs. For technicians, cross-reference the WX28X326 description with the dishwasher manufacturer’s service manual to confirm whether any additional backflow prevention, anti-siphon devicesor local code-specific fittings are required for a compliant installation.
| Item | Description |
|---|---|
| Length | 6 feet - provides routing flexibility for typical under-sink or rear-cabinet installations |
| Construction | Stainless-steel braided exterior over a plumbing-grade inner tube (verify specific materials on part label) |
| Compatibility checks | Confirm appliance inlet type, shutoff outlet typeand required adapters before install |
Q&A
What is the WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit used for?
The WX28X326 is a 6-foot stainless-steel braided dishwasher water supply hose sold by GE. It is a supply (inlet) connector used to carry potable water from the household shutoff/angle stop to the dishwasher’s water inlet. It is intended for residential dishwasher installations and replacements.
is this a drain hose or a water supply hose?
It is indeed a water supply hose (inlet) only. It carries water to the dishwasher. Do not use it for the dishwasher drain; the drain requires a separate hose designed for wastewater and higher temperatures/chemical exposure.
Will this hose fit my dishwasher and shutoff valve?
The hose is designed to fit standard residential dishwasher inlets and common angle-stop/shutoff fittings. However, there are variations in fittings and thread types across different homes and older appliances.Before buying, confirm the connection types on your dishwasher and shutoff (or remove the old hose to compare). If the threads or sizes differ, adapters are available to convert to a matching connection.
How do I install the WX28X326 safely and correctly?
Basic installation steps: turn off the water at the shutoff; remove the old hose; inspect/clean the threads and check for a rubber gasket or washer in the hose end; connect the hose to the dishwasher inlet and the shutoff/angle stop, hand-tighten both ends and than tighten an additional small fraction of a turn with a wrench-do not overtighten; secure the hose so it is not kinked or rubbing on sharp edges; turn the water back on and check carefully for leaks. If you’re unsure, hire a qualified technician.
What are the material and performance characteristics (durability, temperature/pressure)?
The kit uses a stainless-steel braided exterior over a flexible inner drinking-water-rated tube (commonly EPDM or similar). That construction resists corrosion, abrasion and kinking under normal use. It is intended for standard residential water pressures and household hot-water temperatures. As with all flexible supply hoses, avoid exposing it to freezing temperatures, direct heat sources or abrasions that can shorten its life.
How frequently enough should I replace the braided supply hose?
Replace the hose promptly if you see leaks, bulging, fraying of the braid, corrosion at fittingsor any othre visible damage. As preventive maintenance, many technicians recommend replacing flexible supply hoses every 5-10 years or sooner in locations with high mineral content or frequent pressure spikes. If the hose has leaked once, replace it rather than just tightening fittings.
Can I use the WX28X326 with a water hammer arrestor, angle stopor an adapter?
Yes. The hose can be connected through a properly sized angle stop or via adapters if the existing fittings do not match. If you experience water hammer, installing a water hammer arrestor on the supply line (at the valve) is advisable. Always use compatible fittings and ensure any adapters or arrestors are rated for potable water and the required pressure and temperature.
Is this an OEM GE part and does it have a warranty?
WX28X326 is offered as a GE OEM replacement part. OEM parts are made to match GE appliance specifications for fit and performance.Warranty terms vary by retailer and by GE’s parts warranty policy-check the seller’s return policy and GE’s warranty details for coverage, duration and claim procedures.
In Summary
The WX28X326 GE 6′ Metal Braided Dishwasher Connection Kit serves as the flexible, durable link between a household water supply and a dishwasher. Its metal-braided construction and six-foot length provide corrosion resistance, pressure tolerance and installation versatility, helping maintain a secure, leak-resistant supply connection that supports reliable dishwasher performance and reduces the risk of water damage to cabinetry and flooring.
As water-supply components are subject to wear, corrosion and accidental damage, proper diagnosis and timely replacement are critically important to preserve safety and function. Inspecting fittings, checking for visible wear or leaksand following manufacturer guidelines – or engaging a qualified service professional when needed – ensures the correct part is used and installed to meet compatibility and code requirements. Replacing a compromised connection kit promptly helps avoid larger repairs and contributes to long-term appliance reliability.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
