WX14X10005 GE Washing 4′ Polymer Coated Water inlet Fill Hose 2 Pack is a replacement water inlet hose assembly for residential washing machines,supplied as two 4-foot polymer-coated braided supply hoses with appliance- and supply-side fittings. The component is a flexible fluid conveyance element that connects the household water supply to the washing machine inlet valves, combining a pressure-rated hose core with a protective polymer coating to resist abrasion and kinking in the rear access area of the appliance.
Inside the appliance system the inlet fill hose transmits pressurized hot and cold water from external shutoff valves to the washer’s inlet solenoids and valvesand it must maintain a leak-tight seal at both the supply and appliance connections under dynamic pressure and temperature cycling. It interfaces mechanically with hose fittings and rubber sealing washers and functionally with the inlet valve assembly and the machine’s water-level/fill control system; any restriction, leakor loss of integrity in the hose can affect fill rate, cycle timingand can introduce a risk of water damage to the surrounding area.
In this article readers will find a technical overview of the hose’s function and construction, guidance on compatibility (length, thread/fitting typesand material considerations), common failure symptoms to recognize (visible wear, bulging, leaks, intermittent or slow filling), practical troubleshooting steps to isolate hose-related issuesand replacement considerations including selection criteria, installation best practices, and safety precautions to minimize risk during service.The aim is to provide technicians, engineersand appliance owners with the contextual data needed to assess, diagnoseand replace the inlet hose when appropriate.
Table of Contents
- Function and Role of the Water Inlet Fill Hose in Washer Water delivery and Pressure Regulation
- How the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack Integrates with Fill Valves, Filtersand Chassis Plumbing
- Common Failure Symptoms and Diagnostic Tests for Leaks, Flow Restrictionand Pressure Loss
- Compatibility, Replacement Considerations, and Professional Installation Procedures
- Q&A
- In Summary
function and role of the Water Inlet Fill Hose in Washer Water Delivery and Pressure Regulation
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill hose 2 Pack functions as the fluid conduit between the household plumbing supply and the washer’s inlet valve assembly. The component typically consists of an elastomeric inner tube that contains the flow and a polymer-coated braided outer jacket that provides abrasion resistance, enhanced kink resistanceand easier routing behind appliances. Because the hose simply transmits supply pressure to the appliance, compatibility depends on matching the washer’s inlet nut style and sealing washer arrangement; verify the hose end fittings and the washer inlet geometry before replacement to avoid cross-threading or improper sealing.
- Length and routing: 4′ length facilitates common installations but may require different routing to avoid sharp bends.
- Mechanical protection: polymer-coated braid resists abrasion and reduces external wear on the inner tube.
- Flow behavior: hose diameter and condition affect pressure drop and transient flow during fill cycles.
- Service considerations: inspect sealing washers and crimps for corrosion,bulging,or leaks prior to reuse.
| Item | Description |
|---|---|
| Length | 4 feet-suitable for typical washer placement behind laundry units |
| Construction | Elastomer inner tube with polymer-coated braided jacket for abrasion and kink resistance |
| Operating pressure | Intended for standard residential water pressures; check manufacturer rating and household supply pressure |
The hose does not actively regulate water pressure; it conveys supply pressure to the washer, so fill rates and pressure sensing are controlled by upstream plumbing, pressure regulatorsand the washer’s inlet valve orifice and control strategy. Restrictions such as kinks, internal collapse, or debris trapped at the valve can increase pressure drop and produce slow-fill symptoms or fault codes, while properly sized, undamaged hoses allow the inlet valve to deliver expected flow. In practice, confirm matching fittings, use the hose’s integral sealing washer rather than pipe dope on nut-style connectorsand replace any hose that shows deformation, external coating failure at terminals, or persistent leakage to maintain reliable water delivery.
how the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack Integrates with Fill Valves, Filtersand Chassis Plumbing
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack serves as the flexible conduit between a machine’s external water supply and its internal fill valves and inlet screens. The hose’s internal bore and fittings are made to mate with the common residential fill-valve interfaces used on GE washers, and the polymer coating provides abrasion resistance where the hose is routed against the chassis. in normal operation the hose transmits incoming mains pressure to the fill valve with negligible flow restriction over the 4-foot run; any pressure drop is dominated by the fill valve or an inline filter rather than the hose itself. When integrating with an inlet filter or a factory inlet screen, maintain correct alignment and seating of the rubber washer at the hose coupling to preserve sealing and avoid flow bypass around the filter housing.
Installation and troubleshooting require attention to the valve-thread interface, routingand mechanical strain relief. Before final assembly, inspect and clean the washer’s inlet screen and confirm the hose coupling contains a seated gasket; hand-tighten the connection and apply only moderate additional torque with a wrench-do not overtighten the metal fitting to prevent deforming the gasket or damaging the valve threads. If an external filter, softeneror backflow device is added inline, verify that adapter fittings and pressure ratings match the hose and fill valve; mismatched adapters are the most common source of leaks. Common failure symptoms are leaks at the hose-to-valve joint, chafing where the hose passes chassis openingsand cracking at highly flexed bends; the polymer coating reduces chafe-related failures but does not eliminate the need for proper routing and clamps.
- Connection: compatible with standard residential fill-valve interfaces (verify thread and gasket type before installation).
- Routing: secure with clamps and avoid sharp bends or contact with sheet-metal edges.
- Maintenance: inspect inlet screen and hose gasket periodically and check for leaks under full water pressure.
| Item | Description |
|---|---|
| Length | 4 feet per hose in the 2-pack; choose length to minimize bends and tension. |
| Coating | Polymer jacket to resist abrasion and protect the inner hose from chassis contact. |
| Typical connection | Designed for common residential washing-machine fill-valve fittings; confirm thread/gasket match. |
| Common issues | Leaks at fittings, kinking, chafing; address by replacing gasket, re-routingor securing hose. |
Common Failure Symptoms and Diagnostic Tests for Leaks, Flow Restrictionand Pressure Loss
The water inlet fill hose transfers domestic water supply pressure and flow into the washer’s inlet valve; the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack is a replacement designed to provide abrasion and corrosion resistance while preserving the hydraulic path. Common failure modes include external leaks at crimped fittings or threaded connectors, internal delamination or rupture of the inner tube that creates partial occlusionand kinking or compression of the hose that reduces effective ID and causes pressure drop. These behaviors affect cycle timing and valve operation - for example, a restricted hose can lengthen fill times or trigger low-fill error codes even when household static pressure appears normal.
Diagnostic tests combine visual inspection and simple hydraulic measurements to isolate hose-related issues from valve or supply problems. Start with a visual and tactile check for surface cracks, bulges, softened sectionsor loose fittings, than perform an isolation flow test by disconnecting the hose from the washer and measuring flow into a graduated container while the supply valve is fully open; compare the result to expected household tap flow. Use a pressure gauge at the hose inlet to observe static pressure and dynamic pressure under load (observe drop when the washer valve opens) to identify restrictive loss; localized leaks are confirmed by pressurizing the hose and inspecting joints.If tests show significant flow restriction, persistent pressure drop under loador visible damage such as inner-layer delamination, replace the hose rather than attempting long-term repairs.
- Slow or incomplete fills - measure flow rate with hose disconnected to determine if restriction is in hose or washer valve.
- Visible external leak at connector – check and retighten/replace connector and O-ring; pressure-test hose for internal breach.
- Intermittent pressure loss during fill – use a pressure gauge at inlet while cycling the washer to detect transient drops.
- Kinking or flattened sections – straighten and inspect for permanent deformation; reduced ID indicates replacement.
- Mineral buildup or internal debris - disconnect and flush hose; persistent restriction after flushing indicates internal damage.
| Item | Description |
|---|---|
| Flow rate test | Timing fill of a known-volume container with hose disconnected isolates hose restriction from washer valve issues. |
| Static vs. dynamic pressure | Static pressure at the supply tap vs. pressure during valve open shows pressure loss due to restriction or poor supply. |
| Visual/pressure leak test | Inspect fittings and pressurize hose to locate external leaks or evidence of inner-layer failure. |
Compatibility, Replacement Considerationsand Professional Installation Procedures
The WX14X10005 GE Washing 4′ Polymer Coated water Inlet Fill Hose 2 Pack is an OEM-style replacement assembly used to connect household hot and cold water supplies to the washer inlet valves. These 4‑foot hoses provide the fluid pathway and pressure containment required for normal fill cycles; the polymer coating protects the braided reinforcement from abrasion and external damage while the end fittings engage the standard washer inlet ports. Compatibility depends on matching the inlet thread type and physical routing: most residential washers use 3/4‑inch garden hose thread (GHT) fittings and similar valve spud spacing, but technicians should confirm thread size, valve orientationand clearance before installation to avoid strain or misalignment during operation.
Replacement and installation require verification of the inlet valve condition, proper sealing componentsand leak testing after service. Professional procedure typically includes isolating the water supply, relieving residual pressure, removing the old hoses, inspecting inlet screens and rubber gasketsand fitting new hoses without over‑torquing the connections; avoid twisting the hose during attachment and route it to prevent kinks or contact with sharp edges or heat sources.Practical checks after installation include applying normal supply pressure, exercising the washer through a short fill cycle to inspect for slow leaks at the fittingsand replacing both hot and cold hoses as a set if the other shows age or wear.
- Pre‑installation checklist: confirm thread type and size, measure required length, inspect inlet valve and screens, ensure new gaskets are presentand verify hose routing to prevent kinking.
| Item | Description |
|---|---|
| Length | 4 feet per hose (two hoses per pack) |
| Fitting | 3/4‑inch garden hose thread (GHT) typical for residential washer inlets – verify on unit |
| Construction | Reinforced inner tube with polymer outer coating for abrasion resistance |
| Use | Hot and cold water inlet connection for compatible GE washing machine models; verify model-specific fitment |
Q&A
What is the WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill hose 2 Pack?
WX14X10005 is an OEM replacement set of two 4-foot water inlet/fill hoses designed for washing machines. Each hose is polymer-coated for abrasion resistance and is intended to connect the hot and cold water supply valves to the washer inlet valves.
What size and type of fittings do these hoses use? Will thay fit my washer and shutoff valves?
These hoses use the standard 3/4-inch female threaded swivel fittings used on most residential washing machines and supply stops. They will fit any washer and house shutoff valve that accepts the common 3/4″ inlet thread (the standard washer supply connection). Verify your appliance uses the standard thread if you have an older or specialty installation.
Can I use these hoses for both hot and cold water?
Yes. The hoses are intended for both hot and cold water connections to a washing machine. They are made to handle normal household hot water temperatures used by washers. If you need exact maximum temperature or pressure ratings, check the product specification sheet or packaging.
How do I install the hoses correctly and avoid leaks?
Turn off the water at the supply valves and unplug the washer. Remove the old hoses,making sure to catch residual water. Ensure the rubber sealing washers are seated inside each hose fitting, hand-thread the hose onto the washer inlet and the supply valve to avoid cross-threading, then tighten by hand and give a final small quarter-turn with pliers if needed – do not overtighten. Turn the water back on and check for leaks. If you see leaks, shut the water off and re-seat the washer or fittings and re-tighten. Do not use Teflon tape on the hose end where a rubber washer seals; it is not necessary and can prevent proper sealing.
How long do these hoses last and when should I replace them?
Lifespan depends on water quality, pressureand use. Polymer-coated (or braided) hoses generally last longer than plain rubber hoses, but you should inspect them periodically for bulging, kinks, corrosion, cuts, crackingor leaks. Many technicians recommend replacement every 3-7 years or sooner if any wear is present. Replace immediately if you observe any damage or persistent leaks.
Why is the hose polymer coated and what are the benefits?
the polymer coating protects the inner hose and any metal braid from abrasion, corrosionand surface damage, helps reduce scratching of nearby surfacesand can make the hose more flexible. It provides an extra layer of protection compared with uncoated rubber hoses.
What should I do if a hose leaks right after I install it?
If a leak appears immediately,shut off the supply valve,disconnect the hose,and check that the rubber washer is present and properly seated and that there is no debris or damage to the threads. Reconnect carefully,avoiding cross-threading,and hand-tighten before giving a small additional turn.If the leak persists at the supply valve, inspect the valve and connection for damage; if it persists at the washer inlet, check the inlet valve body for cracks or improper seating.
Is this an OEM GE part and will it work with other major appliance brands?
WX14X10005 is an OEM GE part number for GE washing machine inlet hosesand as it uses the standard 3/4″ washer fittings it will normally work with other major brands (Whirlpool, Maytag, LG, Samsung, etc.) that use the standard connections. If you need warranty,compatibility confirmation,or exact specifications,consult the appliance manual or the hose packaging/spec sheet before purchase.
In Summary
The WX14X10005 GE Washing 4′ Polymer Coated Water Inlet Fill Hose 2 Pack serves as a critical supply component for compatible washing machines, delivering incoming water while the polymer coating helps resist abrasion, corrosion and wear. As a replacement part, its 4‑foot length and two‑piece packaging provide convenience for routine service or simultaneous replacement of multiple hoses, contributing to reliable water flow, consistent machine performance and reduced risk of leaks that can lead to appliance damage and home water loss.
Proper diagnosis and timely replacement are essential to maintain safety and performance: inspect hoses regularly for bulging, cracking, stiffness, leaks, mineral buildup or reduced flowand replace them at the first sign of deterioration or per the manufacturer’s guidance. Use the correct part (WX14X10005) and follow installation instructions or consult a qualified technician when unsure; doing so minimizes downtime, prevents costly water damage and helps preserve the appliance’s expected lifespan.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
