WD24X10062 GE Dishwasher Drain Tube Assembly is a drain tube assembly used on select GE dishwashers that provides a routed path for wastewater from the dishwasher sump and pump to the household drain, disposalor air gap. As a physical conduit assembly it typically consists of molded or flexible tubing, connection fittingsand securing clamps or molded bosses sized to mate with the dishwasher pump outlet and the household plumbing interface. The part number identifies a specific OEM configuration intended to match the original equipment routing, connection geometryand hose material for reliable fit and sealing.
Inside the appliance the drain tube assembly carries discharged water away from the dishwasher sump and pump and interfaces directly with the drain pump outlet, drain valve or check valve arrangementsand the external waste plumbing (air gap, disposalor standpipe). Proper function depends on correct internal routing, slope, secure connections and intact hose material; failures or improper installation can lead to standing water in the tub, backflow into the sump, leakage at fittingsor reduced pump efficiency. The drain tube therefore interacts with the wash and drain cycle control, the pump and motor assemblyand the household waste system, making it an integral component of the overall drainage subsystem.
In the following article readers will find technical detail about the WD24X10062 drain tube’s function and typical construction, guidance on model compatibility and how to verify OEM part selection, common failure symptoms to watch for (kinks, blockages, splits, loose fittingsand related error indications), recommended troubleshooting checks to isolate whether the tube or another component is at faultand practical replacement considerations such as routing, attachment points, sealing methods and inspection points to ensure proper operation after service. The focus is on diagnostic criteria and service-relevant data useful to technicians, engineers and appliance owners evaluating or replacing this component.
Table of Contents
- Function and Role of the Drain Tube Assembly in Dishwasher Fluid Management and Backflow Prevention
- How the WD24X10062 GE Dishwasher Drain Tube Assembly Works Inside the Appliance
- common Failure Symptoms: Leak Detection, Blockage Indicatorsand Performance Degradation of the Drain Tube
- Replacement Considerations, Model Compatibilityand Stepwise Installation Procedure for Drain Tube Assemblies
- Q&A
- To Wrap It Up
Function and Role of the Drain Tube Assembly in Dishwasher Fluid Management and Backflow Prevention
The WD24X10062 GE Dishwasher Drain Tube Assembly provides the flexible, sealed path that carries wastewater from the dishwasher pump/sump to the household drain system while supporting measures that prevent wastewater backflow into the tub. Functionally it must accommodate pump discharge pulses, resist collapse or kinking, and mate with the dishwasher discharge fitting and either an under-sink air gap or a properly secured high loop. In many GE installations the assembly includes a molded elbow and a retention clamp that match the chassis outlet; compatibility with the original connector geometry and inside diameter is critical to maintain flow performance and a reliable seal.
- Check connector type and inside diameter for proper fit and flow.
- Route and secure the tube to form a high loop or connect to an air gap to prevent siphoning.
- Inspect for cracks, crimps, blockages, or loose clamps during replacement.
- Use smooth bends and avoid sharp kinks to minimize restriction and wear.
| Item | Description |
|---|---|
| Material | Flexible corrugated plastic/PVC designed to resist chemical exposure and repeated flexing |
| Primary role | Convey pump discharge and participate in backflow prevention when installed with a high loop or air gap |
| Common failure modes | Clogging with debris, abrasion or cracking at bends, and loss of seal at fittings |
Fluid behavior in the drain tube is governed by pump head, gravityand the presence of an air break; a correctly routed WD24X10062 GE Dishwasher Drain Tube Assembly will allow rapid evacuation of wash water while preventing reverse flow caused by downstream pressure or siphoning. Practical installation considerations include keeping the drain loop secured to the chassis at a point higher than the tub outlet, ensuring hose clamps are tightened to factory torque to prevent leaks, and verifying that the tube inner diameter and length do not introduce excessive backpressure. When troubleshooting slow drains, gurglingor water remaining in the tub after a cycle, technicians should first verify tube routing and integrity before replacing pumps or valves, sence a misrouted or damaged drain tube is a common, easily remediable cause of such symptoms.
How the WD24X10062 GE Dishwasher Drain Tube Assembly Works Inside the Appliance
The WD24X10062 GE Dishwasher Drain Tube Assembly routes wastewater from the dishwasher sump and pump assembly to the household drain or garbage disposal, providing a flexible, kink-resistant conduit designed to withstand detergent exposure and elevated temperatures. During the drain cycle the pump forces water through the tube while integrated check valves and a properly formed high loop or air gap prevent backflow and siphoning; correct inner diameter, routingand secure clamp connections are necessary to maintain flow velocity and avoid retention of soiled water in the tub.
- Common symptoms of a compromised drain tube: standing water after a cycle,intermittent gurgling,visible leaks at fittings,or debris build-up visible at disconnection points.
- Practical features to verify: matching inner diameter and attachment type to the pump outlet, adequate length for a high loop or air gap, material resistance to heat and detergentsand undamaged, kink-free routing.
Technicians should inspect the drain tube assembly for blockages, soft or cracked sectionsand secure clamps at the pump and disposal/discharge connections; a quick functional check is to disconnect the tube, run the pump briefly into a bucket to confirm unobstructed flow, then reattach using new clamps if corrosion or deformation is present. When replacing the tube, select a part that matches the original hose diameter and fittings, ensure the routing allows a high loop or air gap to prevent siphoningand avoid incidental contact with heating elements or sharp edges that can accelerate degradation.
| Item | Description |
|---|---|
| Material | Flexible, detergent-resistant plastic (PVC or reinforced elastomer) |
| Typical diameter | Approximately 5/8″-1″ inner diameter depending on model |
Common Failure Symptoms: Leak Detection, Blockage Indicators, and Performance Degradation of the Drain Tube
The WD24X10062 GE Dishwasher Drain Tube assembly serves as the primary wastewater conduit from the dishwasher pump to the household drain connection. It is indeed a flexible hose engineered to withstand repeated exposure to hot, soapy water and small particulate debris; proper function depends on secure hose-to-pump and hose-to-drain fittings, a correctly formed high loop or air gap to prevent backflowand adequate bend radius to avoid kinks. Technicians should verify OEM compatibility with the appliance model and inspect common stress points near the pump outlet and disposal connection-loose clamps, abrasion where the hose contacts the cabinetor repeated bending during installation are typical precursors to mechanical failure or slow degradation of the tube material.
Failures of the drain tube moast often present as fluid leaks,restricted flow,or downstream performance issues that affect cycle completion and rinsing effectiveness. Symptoms can be subtle (intermittent gurgling when the sink is used) or obvious (pooling water under the dishwasher); practical troubleshooting includes visual inspection for cracks or splits, feeling for soft spots along the hose wall, disconnecting and flushing the tube to confirm flowand ensuring the high loop/air gap is properly positioned to prevent siphoning.
- Visible leaks or moisture under the unit – check clamp integrity and hose integrity at both ends.
- Slow drain or standing water in the tub – disconnect and flush the tube to locate a blockage.
- Gurgling noises from the sink or dishwasher during drain – indicates partial obstruction or incorrect routing.
- Dishwasher cycle errors or incomplete drain phases – may originate from restricted flow or intermittent leaks.
- Persistent odor – trapped food debris in a collapsed or sagging section of hose.
| Item | Description |
|---|---|
| Leak source | Cracked hose, loose clamp, or damaged connection at pump/disposal. |
| Blockage location | Near pump outlet, mid-hose sagor at the disposal/sink connection; removable by flushing or replacement. |
Replacement Considerations, Model Compatibilityand Stepwise Installation Procedure for Drain Tube Assemblies
The WD24X10062 GE Dishwasher Drain Tube Assembly is a flexible conduit that conveys wash and rinse wastewater from the dishwasher sump to the household drain or air gap while preventing backflow and siphoning. Functionally it must maintain a continuous fall and retain internal diameter under operating pressure and temperature; typical materials are heat- and detergent-resistant elastomers that resist softening and collapse. Common failure modes include cracks at molded fittings, kinks that reduce flowand internal obstructions from food debris or mineral buildup. Technicians should evaluate hose condition, connector type (barbed, push-fitor crimped)and clamp style before replacement to ensure a leak-free joint and proper hydraulic slope (typically 1/4″ per foot toward the drain).
Replacement compatibility depends on connector geometry, effective lengthand any integrated features such as a one-way valve or molded elbow; OEM part numbers and measurements are the primary verification methods. for practical installation, isolate power and water, remove the lower access panel, disconnect the old hose at both ends, verify that the drain path rises to the air gap or disposer connection as requiredand secure the new assembly with corrosion-resistant clamps to the specified torque to avoid deformation. Typical stepwise actions include the following basic sequence to restore reliable drainage and prevent leaks:
- Power off and unplug the dishwasher; shut off water if recommended by the manufacturer.
- Remove the toe-kick or lower access panel to access the sump and drain connections.
- Place a towel under connections, loosen clampsand detach the existing drain tube from the sump and drain/air-gap/disposer.
- Inspect and clean the inlet/outlet fittings and trap area; measure and compare diameters and lengths before installing the replacement.
- Fit the new drain tubeorienting any molded elbows correctlyand secure with clamps; trim only if necessary to preserve proper slope.
- restore power and run a short fill-and-drain cycle while checking all joints for leaks and verifying that drainage is unobstructed.
| Item | Description |
|---|---|
| Material | Heat- and detergent-resistant elastomer (flexible hose with molded fittings) |
| Connection types | Barbed with worm clamp, crimpedor push-fit; match OD/ID to sump and disposer/air-gap |
| Typical failure signs | Cracks at fittings, flattened sections, persistent leaks, slow drainage |
| Compatibility check | Compare OEM part number or measure inner diameter, connector styleand effective length |
Q&A
What is the WD24X10062 drain tube assembly and which dishwashers use it?
WD24X10062 is an OEM drain tube assembly used on many GE-built dishwashers (and some models sold under Hotpoint/Amana). It connects the dishwasher sump/pump outlet to the sink drain or disposal. Compatibility varies by model year and configuration, so always confirm fit by checking your dishwasher’s model number against the GE parts list or an authorized parts seller before buying.
What are the common symptoms that the WD24X10062 drain tube needs replacement?
Typical signs include visible cracks or splits in the hose, water leaking from under the dishwasher or under the sink at the hose connections, standing water in the tub after drain cyclesor recurring clogs that cannot be cleared. Also inspect for collapsed/kinked hose sections or deteriorated connection points and grommets.
Can I replace the WD24X10062 myself, and what are the basic steps?
Yes – a competent DIYer or technician can replace it. basic steps: disconnect power at the breaker and turn off water if needed; pull the dishwasher out and remove the lower access panel; place a towel/bucket to catch water; loosen and remove the clamps at the pump outlet and at the sink/disposal connection; remove the old tube and route the new tube the same way (maintain a high loop or air gap); secure with new clamps or worm-gear/spring clamps; reinstall panels, slide the dishwasher back, restore power, and run a drain cycle to check for leaks. Do not overtighten clamps or kink the hose.
what tools and replacement parts should I have on hand to change the drain tube?
Typical tools: flathead or Phillips screwdriver (depending on clamp type),slip-joint pliers,utility knife (to remove zip ties),bucket/towels,and optionally a wet/dry vacuum. Replacement parts: the WD24X10062 hose and new hose clamps or spring clamps (don’t reuse severely corroded clamps). You may also need a replacement sink tailpiece or grommet if those are damaged.
How can I tell whether the drain problem is the hose or the dishwasher pump?
First inspect the hose for visible damage,kinks,or blockages. Disconnect the hose from the pump and run a short drain cycle (or manually pour water into the sump) to see if the pump discharges water out of the pump outlet. If the pump pushes water but it doesn’t flow through the hose, the hose is highly likely clogged or collapsed. If no water is pumped out at all, the pump or motor assembly might potentially be faulty. Also check upstream items (filter, garbage disposal, air gap) for obstructions.
How do I clear a clog in the WD24X10062 drain tube without replacing it?
Turn off power and place a towel/bucket under the connection, then disconnect the hose at the pump or the sink/disposal.Use a garden hose to flush water through the tube,a long flexible brush,or a straightened coat hanger carefully to push debris out.A wet/dry vac can suction out material from the hose. After clearing, reattach the hose, secure clampsand run a drain cycle to confirm the clog is gone. If the hose is brittle, collapsedor repeatedly clogs, replacement is recommended.
Why is water still leaking after I installed a new WD24X10062 hose?
common causes: loose or wrong type of clamps, hose not fully seated on the pump outlet or sink tailpiece, kinked hose restricting flow and causing backpressure at a joint, damaged pump housing or sump, a missing or damaged grommet at the pumpor using the wrong part/orientation. Recheck that the hose is pushed fully onto fittings, use proper clamps, remove kinks, and inspect the pump and sink connections for cracks or defects.
Do I need to install a high loop or air gap when routing the WD24X10062 drain tube?
Yes. The drain hose must be routed with a high loop (secured to the underside of the countertop as high as possible) or connected to a sink-mounted air gap where required by local plumbing code. This prevents wastewater from backflowing into the dishwasher. If your local code requires an air gap, install one between the dishwasher hose and the sink drain/disposal.
to Wrap It up
The WD24X10062 GE dishwasher drain tube assembly serves a straightforward but essential role in the appliance’s operation: it channels wastewater away from the tub to the drain system and helps maintain a watertight path that prevents leaks, backupsand related appliance damage. Because it interfaces with seals, clamps and the dishwasher’s drain components, its condition directly affects drainage performance, overall hygieneand the long‑term reliability of the machine.
Timely and accurate diagnosis of drain-related symptoms-such as slow draining, unusual noisesor visible leakage-helps determine whether the issue can be remedied by cleaning or requires replacement of the WD24X10062 assembly. Replacing a compromised drain tube with the appropriate, compatible part and observing recommended installation practices restores proper function and mitigates the risk of further damage. For best results and safety, diagnostic and replacement decisions should follow manufacturer guidance or be performed by a qualified service technician.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
