241860801 Frigidaire Refrigerator Ice Container Assembly is a molded ice storage and dispensing module used in select Frigidaire freezer units; it functions as the receptacle that receives ice from the icemaker and presents it too the dispenser or user-access area. The component is typically a plastic bin or assembly that includes mounting features, guide rails or chutes for ice flow, and interfaces for the auger or dispenser mechanism, and it is indeed engineered to fit into a specific freezer cavity geometry and mounting pattern.
Inside the appliance the ice container assembly interfaces directly with the icemaker output,the ice-dispensing auger or paddle,and any associated sensors or switches that detect ice level or bin presence. It also interacts indirectly with the freezer habitat - thermal cycling, frost accumulation, and defrost cycles can affect its performance - and must maintain proper clearances so the auger can turn freely and the dispenser door or chute can seal.Proper alignment and secure mounting are essential to prevent jamming, misfeeds, or mechanical wear on the dispenser drive components.
This article will describe the 241860801 assembly’s function and mechanical layout, how to verify compatibility with specific Frigidaire models, common failure symptoms and diagnostic checks, practical troubleshooting steps to isolate mechanical or sensor-related causes of ice feed problems, and replacement considerations such as mounting hardware, seal condition, and adjustment procedures. Technical guidance will focus on inspection, measurement, and safe replacement practices so technicians, engineers, and appliance owners can evaluate service needs and plan repairs accurately.
Table of Contents
- Function and Role of the Ice container Assembly in frigidaire Refrigeration Systems
- How the 241860801 frigidaire refrigerator Ice Container Assembly Operates and Integrates with ice-Maker and Dispenser Components
- Common Failure Symptoms and Diagnostic Indicators for the Ice Container Assembly
- Compatibility, Replacement Considerations, and Installation Procedures for Affected Frigidaire Models
- Q&A
- In Conclusion
Function and Role of the Ice Container Assembly in Frigidaire Refrigeration Systems
The 241860801 Frigidaire refrigerator Ice Container Assembly is the molded ice storage bin that receives cubes from the ice maker, channels them into the auger or gravity chute, and provides the mechanical interfaces - mounting tabs, alignment pins, and sensor actuation points – required for reliable dispensing.Its primary function is passive containment and guidance: the interior geometry minimizes cube bridging and directs cubes into the auger drive while the external geometry locates the bin relative to the ice maker module and dispenser door. Correct part fit preserves actuator timing and sensor travel so that the control board receives accurate full/empty signals and the auger engages only when cubes are properly seated in the feed path.
Service technicians evaluate the assembly for cracks, warped mounting features, frost accumulation, or obstructed drain channels that alter cube flow or cause false sensor readings.Practical examples include a broken front lip that lets cubes fall ahead of the auger and create dispenser jams, or excessive frost on the bin interior that increases bridging and reduces usable capacity.When replacing the bin, match the mechanical mounting points and any sensor/actuator interface; electrical connectors and auger alignment must be verified on installation to restore correct timing and to avoid noise or dispensing failures.
- Molded material and interior slope to reduce ice bridging
- Mounting tabs and alignment pins that locate the bin to the ice maker and dispenser
- Integrated chute/auger feeding path and sensor/actuator pockets
- Drain/vent features to manage meltwater and limit frost buildup
| Item | Description |
|---|---|
| Part | 241860801 Frigidaire Refrigerator Ice Container Assembly – replacement ice bin for compatible frigidaire models |
| Function | Collects and feeds ice to auger/dispenser; provides sensor actuation and mounting interface |
| Common failure modes | Cracked bin or damaged tabs, interior frost/bridging, misaligned sensor actuation causing false full/empty signals |
| Repair/replace guidance | Confirm mechanical fit and sensor/auger alignment; inspect drain paths and defrost if frost accumulation is present |
How the 241860801 Frigidaire Refrigerator Ice Container Assembly Operates and Integrates with Ice-Maker and dispenser Components
The 241860801 Frigidaire Refrigerator Ice Container Assembly is the molded ice bin that receives cubes during the icemaker’s harvest cycle and provides the mechanical and sensor interfaces to the dispenser system. It aligns beneath the icemaker discharge chute,captures expelled cubes,and presents them to the dispenser opening or auger mechanism. The part’s geometry (sloped floor, guide ribs and a defined outlet) promotes reliable cube flow while the molded mounting tabs and catches ensure repeatable positioning so that mechanical couplings and any bin-mounted sensors line up with the refrigerator frame and dispenser drive components.
During normal operation the icemaker periodically harvests frozen cubes and pushes them into the container; gravity and the container’s internal guides move ice toward the dispenser access point.Proper function requires correct seating of the container so the dispenser motor hub, auger or paddle engages the bin coupling and any interlock switch or optical sensor sees the expected position. Incompatibility or misalignment-such as using a different bin design or a warped latch-can cause jams, prevent the dispenser drive from engaging, or give false “bin full”/“no ice” signals. For troubleshooting and field replacement, verify seating, inspect the outlet for bridged ice, and confirm that the bin’s arrestor/gear interfaces match the dispenser drive before declaring the icemaker or motor defective.
- Mounting alignment: ensures dispenser drive and sensors engage only when bin is correctly seated.
- Ice flow design: sloped floor and guide ribs reduce bridging and promote consistent dispensing.
- Sensor/interface compatibility: may interface with a mechanical switch, optical sensor, or the dispenser drive coupling depending on model.
| Item | Description |
|---|---|
| Mount points | Molded tabs/catches that position the bin relative to the icemaker and dispenser frame. |
| Dispenser interface | Outlet geometry and coupling features that mate with the auger/paddle or dispenser motor shaft. |
| Sensor connection | Physical location and orientation for bin-present/full sensors (mechanical or optical) used by the refrigerator control. |
Common Failure Symptoms and Diagnostic Indicators for the Ice Container Assembly
The 241860801 Frigidaire Refrigerator Ice Container Assembly is the removable ice storage and delivery module that receives ice from the icemaker and supplies it to the dispenser or internal bin. It typically comprises the bin, lid, mounting flanges, a drive hub or auger interface, and one or more mechanical or optical sensors that signal full/empty status to the control board. Functionally, the assembly must provide a low-friction path for ice to move, a secure mechanical interface for the drive components (check the drive coupling and hub for wear), and a proper seal with the cabinet to avoid air infiltration that causes melting and re-freezing. compatibility is primarily mechanical and electrical: the container must align with the icemaker output and the dispenser drive, and the sensor connectors must match the refrigerator wiring harness on supported Frigidaire models.
Common failure symptoms are frequently enough diagnostic if inspected systematically: inconsistent or no dispensing usually points to a worn or broken drive hub, jammed or bridged ice indicates improper bin geometry or warm temperatures, and false “bin full” signals commonly result from misaligned or damaged sensor flags. Practical checks include confirming the bin is fully seated,rotating the auger by hand to verify free movement,measuring freezer temperature near the icemaker,and visually inspecting sensor flags and wiring for damage.The table and list below summarize typical symptoms and the most likely diagnostic indicators to guide repair decisions.
- No ice dispensed while motor runs - check auger coupling/hub for breakage or stripped teeth and ensure the bin is properly seated.
- Frequent ice jams or bridged ice – inspect freezer temperature, airflow obstructions, and signs of partial thaw/refreeze in the bin.
- water leakage or ice melting in bin - verify seal integrity, door gasket condition, and that the bin is not contacting warm cabinet surfaces.
- False full/empty indications – examine sensor flags, optical sensor lenses for frost/ice, and connector continuity to the main harness.
| Item | Description |
|---|---|
| auger/Drive Hub | Visual and hand-rotation check for stripped teeth, cracks, or disengagement from the motor shaft. |
| Sensor flag/Lens | Verify alignment and cleanliness; frost buildup or broken flags produce incorrect full/empty signals. |
| Bin Seating | Confirm mechanical latches and mounting points are intact and that the bin fully engages the dispenser drive. |
| Freezer Temperature | measure temperature near the icemaker; >5°F above nominal can cause clumping and poor dispensing. |
Compatibility, Replacement Considerations, and Installation Procedures for Affected Frigidaire Models
The 241860801 Frigidaire Refrigerator Ice Container Assembly is the receptacle that collects ice produced by the ice maker and positions it for auger-driven dispensing or manual retrieval. Functionally, the assembly integrates mechanical mounting tabs, an auger coupler interface, and often an ice-level sensor or microswitch that signals the ice maker and dispenser motor; mismatches in any of these interfaces cause dispensing failures or false full/empty indications. Compatibility depends on the cabinet opening dimensions, the style and location of the auger or chute, and the type of sensor used-some Frigidaire models use a photo-optic sensor while others use a spring-actuated switch-so verify the refrigerator model number against OEM parts lists and inspect mounting bosses and connector types before assuming interchangeability.
- Disconnect power and empty ice bin before removal to prevent motor damage and make inspection easier.
- Confirm mechanical fit: check tab spacing, screw boss locations, and auger coupler geometry against the removed unit.
- Inspect the sensor and actuator alignment; if present, replace the sensor gasket or retainer to maintain proper detection.
- After installation,run a manual rotate test of the auger and a single ice-maker harvest cycle to verify feed and sensor operation.
replacement procedure considerations include verifying drive-coupler engagement depth (insufficient engagement leads to stripped splines) and ensuring the container seats flush against the dispenser throat to avoid ice bridging. During installation, secure fasteners to a snug torque-hand-tight plus a quarter turn on plastic bosses-so bosses do not crack; if metal screws penetrate thin plastic walls, use thread-forming screws sized per the service manual. Practical troubleshooting after replacement: if the auger stalls, check for obstructions and confirm that the microswitch or optical sensor is being actuated by the container tab; if the dispenser drive turns but ice is not delivered, inspect the auger coupling for hairline fractures or missing splines and verify continuity of any sensor wiring with a multimeter.
| Item | description |
|---|---|
| Part | 241860801 Frigidaire Refrigerator Ice Container Assembly |
| Mounting interface | Plastic tab bosses and screw mounts; mating dimensions must match cabinet throat |
| Drive interface | Splined auger coupler-verify spline count and engagement depth |
| Sensor type | varies by model: optical sensor or mechanical microswitch; confirm connector pinout |
Q&A
What is the 241860801 Frigidaire Ice Container assembly and what does it include?
The 241860801 is the OEM ice container (ice bin) assembly sold for manny Frigidaire/Electrolux refrigerators. It generally includes the plastic ice bin and the trim/chute pieces that guide ice to the dispenser. It typically does not include the ice maker module, auger motor, dispenser motor, or electrical components unless the specific product listing explicitly states those items are included.
How do I confirm this part is compatible with my refrigerator model?
Check the refrigerator’s model number (usually on a tag inside the cabinet or on the frame) and use that model number in an official Frigidaire parts lookup or with a trusted parts dealer.Cross-reference 241860801 against the compatibility list shown by the seller or Frigidaire. If in doubt, contact Frigidaire support or the parts vendor with your appliance model number to confirm fit.
How do I install the 241860801 ice container assembly?
Turn off the refrigerator or disconnect power for safety.Remove any remaining ice and open the freezer door. If there is an old container, disengage any retaining clips or screws and slide the old bin out. Position the new container in the housing,align the guide tabs and chute,secure any screws or clips,and reattach any trim pieces. Restore power and run the dispenser (if applicable) to confirm proper alignment. Typical install time is about 10-30 minutes depending on model and access.
My ice dispenser is jamming-could the ice container assembly be the cause?
Yes, the bin can contribute to jams if it is cracked, warped, or misaligned so ice hangs up at the chute. However, jams are also commonly caused by overfilled/packed ice, broken auger/drive components, a seized dispenser motor, or ice maker delivering wet/slushy ice. Inspect the bin for damage and proper seating first; if the bin looks fine, check the auger, motor, and dispenser drive for faults.
does the 241860801 come with mounting hardware and electrical connectors?
In most cases the ice container assembly is supplied as the plastic bin and trim only; small mounting clips may be included but electrical components (wiring harnesses, sensors, auger motors) are usually sold separately. Review the seller’s parts description or the OEM parts diagram to confirm what is included before purchase.
How should I clean and maintain the ice container to prevent odors and jams?
remove the bin and empty the ice.Wash with warm water and mild dish soap, rinse thoroughly, and air dry. For deodorizing, you can use a solution of 1 tablespoon baking soda per quart of warm water. Avoid abrasive cleaners and very hot water that can warp the plastic.While some bins are top-rack dishwasher-safe, hand washing is safest to prevent damage.
How can I tell if the ice container assembly needs replacing versus another part of the ice system?
Replace the bin if you see visible cracks, warping, broken tabs/clips, or if it won’t seat properly in the housing. If ice production, dispensing, or auger movement is the issue but the bin looks intact and seats correctly, the problem is more likely the ice maker, auger motor, dispenser motor, or control board. Use visual inspection and simple tests (e.g., run dispenser motor, listen for auger, manually rotate auger if accessible) to isolate the fault before replacing the bin.
Is 241860801 an OEM part or are there aftermarket alternatives, and which should I buy?
241860801 is an OEM Frigidaire part number. There are aftermarket bins available that may be less expensive, but OEM parts ensure exact fit and appearance. If you want guaranteed fit and warranty backing, purchase the OEM part from Frigidaire or an authorized dealer. aftermarket parts can be acceptable if the seller provides clear compatibility facts and a return policy.
In Conclusion
The 241860801 Frigidaire Refrigerator Ice Container assembly serves as an essential component in maintaining ice storage and delivery within compatible Frigidaire refrigerator models. By securely holding the produced ice, aligning with the dispenser or auger mechanism, and maintaining hygienic separation from other compartments, the assembly contributes directly to consistent ice quality, reliable dispensing, and overall appliance performance.
Timely and accurate diagnosis of issues affecting the ice container-such as cracking, misalignment, contamination, or interference with dispensing mechanisms-is important to avoid secondary damage and to restore normal operation efficiently.When replacement is necessary, using the correct assembly and ensuring proper installation preserves fit, function, and safety; conversely, delaying replacement or fitting incompatible components can lead to jams, water leaks, or reduced ice quality.
the 241860801 ice container assembly plays a practical role in refrigerator functionality and user convenience. Routine inspection, prompt diagnosis of any faults, and professional or manufacturer-recommended replacement when required help maintain performance, hygiene, and long-term reliability of the appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok