316011200 Frigidaire Oven Top Burner Ignitor is an ignition device designed for use in gas cooking appliances; it serves as the electrical component that initiates combustion at a top or oven burner and is typically supplied as a direct-replacement part for compatible Frigidaire range models. the component may be implemented as a hot-surface (glow) ignitor or as a spark-type electrode depending on the appliance design, and it is built to withstand thermal cycling and the high-temperature surroundings instantly adjacent to the burner assembly.
Functionally, the ignitor interfaces with the appliance’s control module, gas valve, and wiring harness to provide the energy or spark necessary to light the gas stream. In operation it converts electrical input from the control system into either a high-temperature surface or an electrical discharge that reliably ignites the burner; its timing and performance affect valve sequencing, flame establishment, and built-in safety interlocks that shut off gas if ignition does not occur. Technically relevant attributes for service personnel include connector type, mounting orientation, expected electrical characteristics (open-circuit resistance or required ignition voltage/current), and its proximity to the burner and heat shields, all of which influence compatibility and thermal stress during operation.
This article will explain the ignitor’s operating principle and typical electrical and mechanical specifications, identify which Frigidaire models commonly use part 316011200, describe common failure symptoms (such as delayed or absent ignition, intermittent operation, or visible damage), and outline diagnostic approaches technicians use (resistance and voltage checks, visual inspection, and interaction testing with the gas valve and control board). It will also cover practical replacement considerations including matching OEM part numbers and connectors, proper mounting and grounding concerns, and post-replacement verification steps to ensure safe, reliable appliance operation.
Table of Contents
- Functional role and Electrical and Mechanical Requirements of the Top Burner Ignitor
- How the 316011200 Frigidaire Oven Top Burner Ignitor Operates Within the Cooktop Ignition Circuit
- Common Failure Modes and Observable Diagnostic Symptoms of Top Burner Ignitor Faults
- Model compatibility, Replacement Procedure and step‑by‑Step Troubleshooting for the 316011200 Ignitor
- Q&A
- Future Outlook
functional role and Electrical and Mechanical Requirements of the Top Burner Ignitor
The 316011200 Frigidaire Oven Top Burner Ignitor is an electrode-style ignition assembly that delivers the ignition energy required by gas top burners. In operation, the ignitor is driven by the range’s spark-generating module and produces high-voltage, short-duration pulses across an insulated ceramic electrode to create a visible spark at the burner ports.Proper operation requires secure electrical connection to the module, a reliable ground through the stove chassis, and a consistent electrode-to-burner gap; if any of these conditions fail, the burner may not light or will light intermittently. technicians should consider both the electrical interface and the physical condition of the ceramic electrode when diagnosing ignition faults.
Electrical and mechanical requirements for the ignitor include insulation to withstand the kilovolt-range pulses from the ignition module, mechanically stable mounting to maintain a consistent gap under vibration and thermal cycling, and materials resistant to combustion residues and high surface temperatures. Practical checks include visual inspection for cracked ceramic or carbon tracking, verification of harness continuity and connector integrity, and confirmation that the ignitor is the OEM-designated replacement for the stove model. When replacing the part, match the mechanical mounting points and connector type to ensure correct alignment with the burner and reliable operation across repeated ignition cycles.
- Visual and electrical inspection: cracked ceramic,carbon tracking,loose connectors,or missing ground.
- Functional check: observe spark at each burner with the control in the ignite position and correct electrode gap maintained.
- Replacement criteria: damaged insulation, persistent no-spark condition after module check, or mismatched mounting/connector.
| Item | Description |
|---|---|
| Electrical input | Kilovolt-range pulses supplied by the ignition module; requires intact insulation and a chassis ground for discharge. |
| Mechanical mounting | Insulated bracket/ceramic electrode that must maintain alignment and gap with the burner ports under thermal cycling. |
| Compatibility | OEM-form replacement for compatible Frigidaire top-burner assemblies; confirm 316011200 against the appliance parts list before ordering. |
how the 316011200 Frigidaire Oven Top Burner Ignitor Operates Within the Cooktop Ignition Circuit
The 316011200 frigidaire Oven Top burner Ignitor functions as the spark-producing electrode assembly in the cooktop ignition circuit. When a burner control calls for ignition, the cooktop’s control board or mechanical switch energizes the ignition transformer or module, which generates a series of high-voltage pulses routed to the ignitor lead. The ignitor converts those pulses into a visible spark across the electrode gap to ignite the gas; proper operation depends on correct electrode geometry, a secure harness connection to the control assembly, and a reliable return path to ground. This part is designed to be electrically and physically compatible with the matching Frigidaire ignition components, so replacing a damaged electrode with a 316011200 unit preserves connector fit and spark alignment for predictable behavior at the burner head.
- Common circuit behaviors: rapid, rhythmic sparking while the valve opens; continuous clicking with no spark indicates electrode damage or a shorted lead.
- Typical failure modes: cracked ceramic insulator,carbon tracking that shunts the spark,broken lead or corroded connector that interrupts high-voltage delivery.
- troubleshooting context: no clicking often points to the control/transformer,whereas visible spark but no flame suggests a gas valve or orifice problem.
Technically, the ignitor is a passive high-voltage endpoint that requires the upstream ignition transformer and control logic to produce pulses; it does not generate voltage itself. For diagnostics, check the harness and connector continuity with power removed, visually inspect the ceramic and electrode gap for erosion, and verify the module is producing pulses at the ignitor lead with appropriate safe test equipment. maintaining the recommended electrode gap and a clean, secure ground improves ignition reliability; if the ignitor shows physical damage or persistent shunting, replacing it with a properly matched 316011200 part avoids mismatched mounting and electrical characteristics that can otherwise cause weak or misdirected sparks.
Common Failure Modes and Observable Diagnostic Symptoms of Top Burner Ignitor Faults
The top-burner ignitor provides the high-voltage discharge or hot-surface heating needed to ignite the gas at a cooktop burner; in many Frigidaire gas ranges this function is performed by the 316011200 Frigidaire Oven Top Burner Ignitor. When this ignitor degrades it changes behavior in detectable ways: the electrode can erode or the ceramic insulator can crack, increasing resistance or allowing leakage to ground, which prevents consistent sparking.mechanical fit and connector type also affect compatibility – an ignitor with the correct electrode length, mounting bracket, and connector will present the expected spark geometry and timing, whereas a mismatched unit can cause delayed ignition or intermittent sparking even if electrically sound.
- No spark or burner fails to light when the control is turned on.
- Weak or intermittent spark that lights only after multiple attempts.
- Continuous clicking even after the burner lights, frequently enough indicating a grounding or switch issue.
- Visible damage: cracked ceramic, corroded electrode, or soot buildup around the electrode.
- Burner only lights when manually lit, indicating the ignitor produces insufficient energy at the gap.
Diagnostic troubleshooting should combine visual inspection with electrical checks and safe handling: isolate gas and power, verify the electrode gap and clean any carbon deposits, than check continuity and the presence of the ignition voltage from the control module with the range powered (qualified technician only). if continuity shows an open circuit or the electrode is physically damaged, replacement is appropriate; if voltage is present at the ignitor connector but no spark occurs, the issue may be wiring or the ignition module rather than the ignitor itself. For replacement, match mounting geometry and connector type to ensure the replacement ignitor delivers the same spark location and timing as the original part, which preserves safe flame establishment and prevents delayed ignition or unsafe gas accumulation.
| Item | Description |
|---|---|
| Continuity test | Check for closed circuit through the ignitor element; an open circuit indicates internal failure and necessitates replacement. |
| Visual inspection | Look for cracked ceramic,eroded electrode tip,or soot; physical damage compromises spark formation and insulation. |
| Connector & fit | Confirm connector type, bracket position, and electrode length match the original to maintain correct spark geometry and timing. |
Model Compatibility, Replacement Procedure and Step‑by‑Step Troubleshooting for the 316011200 Ignitor
The 316011200 Frigidaire Oven Top Burner Ignitor is a resistive hot-surface element designed to heat to incandescence and ignite the burner by transferring heat to the gas valve/mixture; it is not a spark-type ignitor. Functionally, this component behaves as a low-voltage resistive heater that must reach a specified temperature and exhibit stable electrical continuity to allow the gas valve sequence to operate. Compatibility is determined by mechanical mounting, connector type (commonly two spade terminals) and the element’s electrical characteristics, so replacement requires matching the physical bracket, terminal spacing and the electrical behavior rather than only the part number. Technicians should verify fit and terminal configuration against the appliance model sheet or parts diagram before installation; many Frigidaire ranges use interchangeable ignitors, but visual and measurement confirmation prevents misfit or improper operation.
replacement and troubleshooting follow a methodical sequence that isolates electrical, mechanical, and valve-related causes. Start by taking safety precautions: disconnect electrical power and the gas supply, then remove the burner cap and mounting screws to access the ignitor; note wire routing and terminal orientation. Use a digital multimeter to check for continuity or an open circuit, inspect the ceramic for cracks or glazing, and confirm secure, corrosion-free spade connections. If the element glows but the valve does not open, measure the circuit current under call for flame (compare to the oven/range service data) as a weakened element can still glow but fail to draw sufficient current. Typical fault indicators include open circuit on continuity test, visible ceramic damage, intermittent operation, or proper glow with no gas flow (indicating valve or wiring issues). Follow these practical steps when diagnosing and replacing the ignitor:
- Verify power and confirm correct voltage at the ignitor connector with appliance powered off for continuity checks and powered on only for live-current tests if trained and equipped.
- Inspect and clean terminal connections; replace crimp or spade connectors that are corroded or loose.
- Measure continuity; an open reading indicates replacement is required.
- If continuity exists but burner fails, measure operating current and compare to service data or replace with a known-good unit to confirm load behavior.
- Install new ignitor with identical mounting and terminal orientation, restore gas and power, and observe safe operational test for stable ignition.
| Item | Description |
|---|---|
| Connector | Typically 2 spade terminals; confirm spacing and orientation before replacement |
| Failure modes | Open circuit,cracked ceramic,increased resistance,intermittent connection |
| Diagnostic checks | Continuity test,visual inspection,operating current measurement under call-for-flame |
| Installation notes | Match mounting bracket and terminal layout; secure connections and verify no wire chafing |
Q&A
What is the 316011200 Frigidaire oven top burner ignitor?
The 316011200 is an OEM ignitor used on certain Frigidaire gas ranges/ovens for the top (cooktop) burner ignition system.It is the component that produces the heat or spark needed to light the gas at a surface/burner port depending on the design. Always confirm part numbers against your appliance model before ordering.
what are common symptoms that the 316011200 ignitor is failing?
Typical signs include one or more burners failing to light,intermittent lighting,a weak or uneven flame,repeated clicking without ignition,visible cracks or damage to the ceramic or electrode,or a burner that lights only after several attempts. Electrical tests can confirm the fault.
How do I check if this ignitor is compatible with my Frigidaire range?
Check the model number on the appliance (usually on the frame behind the oven door or on the back) and cross‑reference it with the part number in the Frigidaire parts lookup or a trusted parts supplier. Visual match of the mounting holes, connector type, and electrode configuration also helps confirm compatibility. If unsure, provide your full appliance model to the parts seller or Frigidaire support.
How can I test the ignitor safely?
Turn off power and gas to the appliance before testing. For an electrical continuity check, disconnect the ignitor from the harness and use a multimeter to check for continuity or resistance; an open circuit indicates failure. For spark-type ignitors visually check for consistent spark during an ignition cycle (power on, burner control turned to light). Do not attempt live testing of gas flow or operate the range with panels removed; if you are uncomfortable with electrical or gas work,hire a qualified technician.
Can I replace the 316011200 ignitor myself and what precautions should I take?
Many owners can replace the ignitor with basic tools, but you must disconnect electrical power and shut off the gas supply first. Typical steps: remove grates/burner caps, remove burner assembly or access panel, disconnect wire harness, unfasten mounting screws, replace ignitor, reconnect harness, restore power and gas, and test.Handle the ignitor carefully (do not touch the ceramic/heater element) and follow the appliance’s service manual. If you are not confident working with gas appliances or live wiring, hire a licensed technician.
What tools and parts will I need to replace the ignitor?
Common tools: screwdriver set (Phillips/flat), socket set or nut driver, needle‑nose pliers, multimeter (for testing), and possibly a putty knife to remove panels. Parts: the replacement 316011200 ignitor (OEM recommended) and, if needed, a replacement harness or mounting hardware. Have the appliance model number handy to ensure correct parts.
the new ignitor is installed but the burner still won’t light – what should I check?
Check that the ignitor wiring harness is fully connected and not damaged, confirm the gas supply is on, and verify the burner ports and cap are clean and properly seated. If the ignitor glows or sparks but no gas flows, the gas safety valve or valve solenoid may be faulty. If there is no spark or glow, recheck wiring and the control module. When in doubt, stop and contact a qualified service technician because diagnosing gas flow or valve issues can involve hazardous procedures.
How long does the 316011200 ignitor usually last and how much does it cost to replace?
Expected life varies with use and conditions but commonly ranges from several years to a decade or more. Frequent cycling, spills, or physical damage shorten life. Replacement cost for the part alone typically ranges from an affordable OEM part price to moderately higher for aftermarket alternatives; labor costs add if a technician is used. Check current prices from Frigidaire or authorized parts dealers for an exact figure.
Future Outlook
The 316011200 Frigidaire oven top burner ignitor plays a central role in the safe and reliable operation of a gas cooktop by initiating and sustaining the burner flame. As a critical component, it contributes to consistent heating performance, efficient fuel use, and reduced risk of unignited gas accumulation; maintaining a properly functioning ignitor helps preserve overall appliance performance and user safety.
As symptoms of a failing ignitor can resemble other gas or electrical issues, accurate diagnosis is critically important before replacing the part. When replacement is required, using the correct 316011200 component and following appropriate installation practices-ideally performed or verified by a qualified technician-helps restore performance, maintain manufacturer compatibility, and reduce the likelihood of recurrence. Timely, correct action ensures the appliance operates safely and efficiently over the long term.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok