131758600 Frigidaire Control Timer is a timed control module used to sequence adn switch electrical circuits in compatible Frigidaire appliances. Structurally the component functions as a control timer (either an electromechanical stepper or a solid‑state timing module depending on the model year) that provides scheduled contact closures and logic outputs to initiate and terminate discrete appliance operations.
Inside an appliance the control timer acts as the sequencing hub, coordinating interactions between drive motors, heating elements, valves, pumps, door or lid interlocks and user controls or sensors. It provides timed power to relays and loads, accepts input from door switches and cycle selectors, and often supplies feedback to indicator lamps or displays. Because it controls both low‑voltage logic and line‑voltage switching paths, its failure can interrupt multiple subsystems and manifest as stopped cycles, no heat, or loss of timed functions.
In this article readers will find a technical overview of how the 131758600 control timer performs its functions, which Frigidaire models and wiring harness configurations it is compatible with, common failure symptoms and diagnostic checks (visual inspection, continuity and voltage measurements, and signal tracing), and practical troubleshooting and replacement considerations such as verifying part numbers, connector pinouts, mounting orientation, safety precautions when working with line voltage, and testing after installation.
Table of Contents
- Function and Role of the Control Timer in Refrigeration Cycle Management
- How the 131758600 Frigidaire Control Timer Operates Within the Appliance Control circuit
- Common Failure Symptoms and Measurable Diagnostic Indicators
- Compatibility, Replacement Considerations, and installation Best Practices for the 131758600 Frigidaire Control Timer
- Q&A
- In Summary
Function and Role of the Control Timer in Refrigeration Cycle Management
The 131758600 Frigidaire Control Timer serves as a sequencing device that governs the refrigeration cycle and defrost events by opening and closing internal relay contacts on a set schedule. In practical operation it provides compressor-on/off timing, initiates evaporator fan and defrost-heater circuits, and enforces compressor-off delays to prevent short‑cycling.The timer can be an electromechanical cam timer or an electronic timing module; regardless of construction, it interfaces with the appliance power supply and the thermostat or temperature sensor, translating timing logic into physical contact closures that command the compressor, fans, and defrost elements.
For technicians evaluating compatibility or troubleshooting faults, confirm the timer’s terminal layout, rated voltage, and programmed intervals before replacement-mismatched timing programs or incorrect harness pinouts will produce symptoms such as continuous defrost, no compressor run, or repeated short cycles.Typical diagnostic checks include verifying supply voltage at the timer, observing contact state over a cycle, and comparing observed defrost intervals to the appliance specification; if the module is failing, replacement with a part that matches the timer function and connector configuration is the proper corrective action. Practical examples include replacing a timer that leaves the evaporator heater energized continuously after defrost or one that fails to provide the required compressor run‑in delay after a power interruption.
- primary functions: cycle sequencing,defrost initiation,compressor anti‑short‑cycle delay
- Common behaviors: timed contact closures,repeatable defrost intervals,interaction with thermostat signals
- Compatibility considerations: terminal layout,voltage rating,timing program and connector harness
- Failure symptoms: stuck in defrost,no compressor operation,rapid short‑cycling
| Item | Description |
|---|---|
| Function | Sequencing of compressor,evaporator fan,and defrost heater via timed contact closures |
| typical voltage | Appliance line voltage (commonly 120 VAC) – verify model specification |
| Timing | Defrost interval and duration are programmed; common ranges are multi‑hour intervals and 15-30 minute defrosts (model dependent) |
How the 131758600 Frigidaire control Timer Operates Within the Appliance control Circuit
The 131758600 Frigidaire Control Timer is a cam-driven sequencing device that directs power to the appliance’s major subsystems by opening and closing discrete contact sets in a timed sequence. In most North American units the timer receives line voltage for its internal drive and provides switched outputs to the drive motor, heating circuit, water inlet valve, drain pump, and user-interface indicators; it also responds to interlocks such as door or lid switches and input from temperature sensors. Inside the control circuit the timer does not perform sensing or regulation itself but orchestrates when other components receive power, so a single failed contact or a stalled timer motor can leave the machine stuck in one part of the cycle or prevent functions like agitation or heating from energizing.
- Primary outputs: motor, heater, inlet valve, pump, and indicators.
- Inputs monitored: lid/door interlock, temperature thermostat, start switch.
- Common behaviors: mechanical cam action with multiple contact banks; timed intervals rather than closed-loop control.
- Typical failure modes: worn/burned contacts, seized timer motor, intermittent continuity on terminal strips.
For diagnosis and compatibility checks, technicians measure continuity across the timer contact terminals according to the service wiring diagram and verify that the timer motor is receiving the expected drive voltage (typically 120 VAC on North American models) and is turning the cam assembly. Practical troubleshooting steps include confirming that interlocks allow the timer to advance, applying controlled mains power to observe step transitions, and inspecting contact surfaces for pitting or carbon buildup; replacing the timer is warranted when contacts show intermittent resistance or the motor fails to advance the cams. When replacing the component, match the terminal layout and harness connector to the appliance model-correct pin assignments and the timer’s gearing/synchronous speed ensure proper cycle timing and compatibility.
| item | Description |
|---|---|
| Timer drive voltage | Typically 120 VAC on North American Frigidaire models; verify against model wiring diagram |
| Controlled circuits | Motor, heater, inlet valve, drain pump, and user indicators via multiple contact banks |
| Diagnostic check | Continuity across contacts, confirmed rotation of timer motor, and correct response to interlocks |
Common Failure Symptoms and Measurable Diagnostic Indicators
The 131758600 Frigidaire Control Timer is the electromechanical timing assembly that sequences power to the machine’s motors, valves, heaters, and timers by opening and closing cam-operated switch contacts or drive motor contacts according to the selected cycle. In practice this component behaves as a rotary switch driven by a small synchronous motor (or equivalent stepper arrangement on some variants); wear in the motor, plastic gear train, or the plated contact surfaces produces typical failure modes such as a stalled dial, intermittent operation of one circuit, or complete loss of cycle advancement.Compatibility issues most commonly arise from differences in terminal numbering, mounting flange geometry, or harness connectors, so effective diagnostics begin with confirming the part number against the appliance model and visually inspecting for physical damage, contact pitting, or melted connector housings before replacing the assembly.
When diagnosing the timer you should measure voltage and continuity at the timer’s terminals while exercising the cycle selector so the relationship between cam position and contact state can be verified. Useful, measurable indicators include an absent mains input at the timer (supply-side failure), an open circuit on the timer motor winding (no continuity), lack of expected voltage at an output terminal when its cam position should be closed (contact or cam failure), or abnormally high current draw at the timer motor (binding or gear friction). For example,if the dial does not advance but incoming mains voltage is present at the timer input,the fault is internal to the timer drive; if the dial advances but a heater or motor does not receive voltage when its contact is closed,the contact or associated trace inside the timer is likely defective.
- Dial does not advance while mains present at input - timer drive motor or gear failure.
- Intermittent operation of a circuit – pitted, dirty, or loose switch contacts.
- No power to a function despite correct selector position – open contact or broken trace.
- Visible burning or melting at terminals – overheating or shorting; replace timer and address underlying overload.
| Item | Description |
|---|---|
| Motor continuity | Expect a measurable low resistance (closed circuit) on the timer motor winding; infinite resistance indicates an open motor or broken lead. |
| Output terminal voltage | With selector in the position that should energize the circuit, mains voltage (e.g., ~120/240 VAC depending on appliance) should appear at the corresponding output; absence indicates contact failure. |
| Contact continuity | Measure continuity across switch contacts while rotating the cam; contacts should close (low ohms) at specific cam positions and open otherwise. |
Compatibility, Replacement Considerations, and Installation Best Practices for the 131758600 Frigidaire Control Timer
The 131758600 Frigidaire Control Timer is the sequencing device that governs timed transitions between functional states-energizing motors, engaging heating elements, and actuating valves-according to the appliance’s programmed cycle. In many frigidaire designs this part uses a synchronous timer motor or an electronic timing module with a defined terminal layout; replacement units must match the original’s electrical rating, terminal count and physical mounting to reproduce correct timing behavior and prevent miswiring. Technicians should verify the timer’s nominal supply voltage and check whether the unit contains internal switches or relies on external relays, since these differences affect compatibility and diagnostic approach.
practical replacement and installation practice reduces rework and service calls: isolate power,document and label every conductor,and preserve the dial orientation or gear alignment so the timer’s cam profile matches the control sequence at power-up. If replacing with a direct-fit OEM unit is not possible, compare the new module’s terminal mapping and cam/synchronous motor speed against the original and bench-test continuity of switched circuits before final assembly; common failure symptoms that indicate a bad timer include erratic cycle advance, persistent single-state operation, or loss of power to one or more load circuits. Below are rapid checks and a compact reference for the main technical attributes to confirm before ordering or installing a replacement.
- Confirm supply voltage and frequency match the original (e.g., 120 VAC, 60 Hz) and that the motor type (synchronous vs. electronic) is identical.
- Compare terminal count and mapping; label wires and take a photo prior to removal.
- Verify mounting hole pattern and dial/gear orientation to maintain correct cam timing.
- Bench-test switched outputs for continuity across cycle positions before reinstalling the assembly.
| Item | Description |
|---|---|
| Function | Sequences appliance operations by switching power to motors, heaters, and valves |
| Electrical | Must match original voltage/frequency and terminal wiring (check for integrated switches) |
| mechanical | Mounting pattern and dial/gear alignment determine correct cycle phasing |
| Diagnostic indicators | Erratic cycling, failure to advance, or loss of specific load circuits |
Q&A
What is Frigidaire part 131758600 and what does the control timer do?
Part 131758600 is a Frigidaire control timer assembly used on some models to sequence and time appliance cycles (such as washer or dryer cycles depending on the model). The timer advances the machine through stages (fill,agitate,drain,spin or heat,tumble,cool down) and makes or breaks power to motors,valves,heaters and other components according to the selected cycle.
How do I know if the 131758600 timer is failing?
Common symptoms of a failing timer include cycles that do not advance or get stuck in one position, intermittent or no power to motors/heaters during expected parts of a cycle, unusual clicking or burning smells from the control area, or the appliance not starting at all. Before assuming the timer is bad, check fuses, door/lid switches, wiring harnesses and other control components as those faults can produce similar symptoms.
What is the safe way to test the timer to determine if its defective?
First disconnect power to the appliance. Access the timer and visually inspect for burned contacts, melted plastic or loose connectors. With the timer disconnected, use a multimeter to check continuity of the timer motor windings and contact paths according to the appliance wiring diagram.With the appliance powered (take extreme caution or have a qualified technician do this), verify proper incoming supply voltage to the timer and that the timer outputs change as you advance it through positions.Refer to the factory wiring diagram for which terminals should be energized in each position. If the timer motor winding is open or contacts do not switch as specified, the timer is likely defective.
Can the 131758600 timer be repaired or should it be replaced?
Most of these timers are designed to be replaced rather than field-repaired. Mechanical contacts sometimes respond to contact cleaner if the fault is just dirty contacts, but electronic modules and failed timer motors are typically replaced. for reliability and safety, replacement with the correct OEM part is generally recommended.
How do I replace the 131758600 control timer?
Unplug the appliance or turn off the breaker. Remove the control panel or access panel to reach the timer. Take clear photos of the wiring and/or label each connector so reassembly is correct. Remove retaining screws and carefully pull the timer free, disconnecting the wire harness or spade connectors. Install the new timer by reversing the steps: connect harness, mount timer, replace panel, restore power and test several cycles. If you’re not comfortable with electrical work, hire a qualified appliance technician.
How do I confirm compatibility before buying a replacement 131758600?
check the appliance model number (usually on a tag inside the door opening, behind the control panel or on the back) and use that model number on Frigidaire’s parts lookup or a reputable parts dealer to confirm the correct part. Cross-reference the part number against manufacturer parts lists; do not rely solely on visual similarity as connections and timing charts can differ between models.
Where can I buy a genuine 131758600 timer and are aftermarket options OK?
You can buy an OEM Frigidaire 131758600 from Frigidaire-authorized parts dealers, national appliance parts retailers, and many online marketplaces. Aftermarket or remanufactured timers may be available but can differ in quality or fit; if you choose a non-OEM option,confirm exact compatibility and return/warranty policies. Keep proof of purchase for warranty and returns.
Does the timer require calibration or programming after installation?
Most control timers do not require special calibration - after installation you should simply restore power and run a test cycle to confirm correct operation. Some modern appliances with electronic controls may require clearing stored error codes or performing a diagnostics/reset procedure; consult the service manual for model-specific post-replacement steps.
In Summary
The 131758600 Frigidaire control timer plays a central role in coordinating the operational cycles of compatible appliances, regulating timing sequences, and ensuring that functions such as wash, spin, defrost or other timed events occur in the correct order. As an integral control component, its proper operation directly affects performance, reliability and user experience; faults in the timer can produce irregular cycles, interrupted operation or complete failure of the appliance to respond to selected programs.
Accurate diagnosis is essential before replacing this module: confirming symptoms, ruling out wiring, sensor or user-interface faults, and verifying error codes helps ensure that the timer is truly the source of the problem. When diagnosis indicates that replacement of the 131758600 control timer is necessary, installing a correctly specified unit and following manufacturer-recommended procedures-safety precautions, correct wiring and calibration-maximizes the likelihood of restoring normal operation and avoiding repeat failures.
Maintaining attention to proper troubleshooting and replacement processes preserves appliance performance and extends service life. Whether performed by a qualified technician or a informed owner following service instructions, thoughtful diagnosis and careful replacement of the 131758600 Frigidaire control timer support reliable, safe operation and reduce the chance of unnecessary repairs.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok