316580615 Frigidaire Range Spark Ignition Switches with Wire Harness are an electromechanical switch assembly used on Frigidaire gas ranges to initiate burner ignition; the assembly combines one or more momentary spark switches with a matched wiring harness and connectors to interface the range controls with the ignition module. As a discrete replacement part it provides the user-accessible actuation surface (via the control knob or switch) and the low-voltage signal path required to trigger the high-voltage spark generator that lights the gas burners.
inside the appliance, the ignition switch and harness sit between the user control (knob or selector) and the spark ignition module and gas valve system. When the switch is actuated it completes a low-voltage control circuit to the ignition module, wich then produces the high-voltage pulses to the burner electrodes; the switch and harness also carry return and ground references and may interface with safety interlocks or timers on the control board. Typical mounting locations are behind the front control panel or on the cooktop console, and the part is critical as a failed switch or harness will prevent proper ignition or can create unsafe continuous sparking or intermittent ignition that affects both performance and safety.
In the following article readers will find a technical overview of how the 316580615 assembly functions in the ignition circuit, guidance on model compatibility and harness/connector pinouts, common failure symptoms to recognize (no spark, continuous sparking, intermittent operation, visible heat or charring), stepwise troubleshooting tests to isolate the switch versus the ignition module or wiring, and practical replacement considerations such as verifying part numbers, connector fit, mounting orientation, and basic safety precautions to observe when servicing the ignition circuit.
Table of Contents
- Function and Role of the Spark Ignition Switch Assembly in Frigidaire Gas Ranges
- How the 316580615 Frigidaire Range Spark Ignition Switches with Wire Harness Operate within the Control and Gas-Valve Circuit
- Common Failure symptoms: No Ignition,continuous Sparking,and Electrical Measurement Indicators
- Replacement Considerations and Stepwise Installation Procedures for the 316580615 switch and Wire Harness
- Q&A
- Closing Remarks
Function and Role of the Spark Ignition Switch Assembly in Frigidaire Gas Ranges
The 316580615 Frigidaire Range Spark Ignition Switches with Wire Harness is a combined rotary switch and connector assembly that selects a burner circuit and completes the electrical path to the range’s spark generator. In operation the switch closes discrete contact sets as the control knob is rotated, routing mains power through the attached wire harness to the ignition module so that the module can issue high-voltage spark pulses at the selected burner’s ignitor. The assembly’s terminal layout and harness length determine compatibility with specific Frigidaire range models; the switch does not create the spark itself but provides the switching logic and power distribution that coordinate ignition pulses with the valve control circuitry and safety interlocks in the appliance.
Technicians typically encounter three practical failure modes: continuous clicking with no ignition,clicking at the wrong burner,or no click at all. Troubleshooting should begin with a visual inspection of the harness and spade connectors for corrosion or loosened tabs, then proceed to electrical verification using a multimeter-checking for continuity across the appropriate switch terminals when the knob is actuated and verifying that the switch routes mains voltage to the ignition module. When replacing the module, confirm pin layout and harness routing on the 316580615 assembly match the range’s connector pattern, secure mounting to avoid contact with burners, and restore power only after proper reassembly to avoid short circuits or errant sparks.
- Common features: discrete burner contact sets, molded harness with color-coded wires, spade terminal connectors, and screw-mount flange for secure attachment.
- Speedy diagnostics: visual connector check, continuity test across actuated terminals, verify presence of mains at the module input when turned to “ignite.”
- Failure causes: heat/grease contamination, bent terminals, broken internal detents, or harness wire fatigue.
| Item | Description |
|---|---|
| terminals | Multiple spade contacts that route power to the ignition module and selected burner circuits |
| Harness | Factory-molded wire set with color coding and connector spacing matched to compatible Frigidaire models |
| Mounting | Screw-flange orientation and latch points to ensure correct alignment with control panel |
How the 316580615 Frigidaire Range Spark Ignition Switches with Wire Harness Operate Within the Control and Gas-Valve Circuit
The 316580615 Frigidaire Range Spark Ignition Switches with Wire Harness function as the user-operated interface that routes power and control signals between the range knobs,the spark generator,and the gas-valve control circuit.When a burner knob is turned to an ignition position the switch provides a switched path that energizes the spark module while also providing the appropriate control signal path that allows the gas-valve solenoid or control board to permit gas flow; the included wire harness groups individual conductors into a keyed connector to ensure correct mating and simplified replacement. in practical use this assembly often provides a momentary contact for active sparking and a subsequent position for sustaining the valve circuit, so the timing and contact continuity of the switch directly determine whether the module sees the expected line-level feed and whether the valve receives its enable signal when the flame is present.
- Primary functions: switch power to spark generator, route control signal to gas-valve circuit, and provide a keyed wiring interface.
- Common failure symptoms: no spark, continuous sparking, intermittent ignition, or gas valve energized without spark.
- Replacement considerations: terminal layout, connector keying, and lead color coding must match the range harness.
Internally the switch uses metal contacts and a rotary mechanism to change connection paths; repeated arcing and carbon tracking will increase contact resistance or cause open circuits, producing intermittent behavior.Technicians diagnose the part by verifying continuity between the appropriate terminals while operating the knob, checking for brittle or broken conductors in the harness, and confirming proper connector seating at the control board and spark module; a handheld multimeter and a wiring diagram specific to the Frigidaire model simplify these checks. For compatibility, match the 316580615 part number to the appliance model or verify the terminal functions (common, switched output to spark module, switched output to gas control) before installation to avoid miswiring and unintended valve energization.
| Item | Description |
|---|---|
| Terminal function | Common (line in), switched outputs to spark module and valve/control signal |
| Contact type | Rotary multi-position switch with multiple contact sets |
| Typical failure symptom | No spark, intermittent spark, or gas valve not receiving enable signal |
Common Failure Symptoms: No Ignition, Continuous Sparking, and Electrical Measurement Indicators
316580615 Frigidaire Range Spark Ignition Switches with Wire Harness provide the mechanical and electrical interface between the user control (knob) and the spark generator. The switch completes a low-voltage control circuit to the spark module so the module issues high-voltage pulses to the electrode; the harness routes those connections and provides the mounting/ground reference. typical failure modes that produce no ignition include open or high-resistance switch contacts, broken or corroded harness wires, and poor connector mating that prevents the control signal from reaching the spark module. By contrast, continuous sparking most frequently enough indicates a switch contact stuck closed, a short from a conductor to chassis ground, or moisture/food residue bridging terminals so the module receives an unrestricted firing signal even when the control is released.
Technicians can use basic electrical checks to distinguish these conditions: a working switch will show continuity only in the actuated (on/light) position and open-circuit in the rest position; a shorted or stuck switch will show continuity in the off position or continuity to chassis ground. Note that the high-voltage spark pulses themselves are not measurable with a standard multimeter, so tests should focus on low-voltage continuity and resistance across the switch terminals and between terminals and chassis. Practical examples: if a knob yields no spark but the module receives supply, measure across the switch – an open reading suggests the switch or harness is failed; if sparks never stop, isolate the harness and check for continuity to ground or a permanently-closed contact. Use safe isolation procedures (disconnect power and remove the harness) before performing resistance checks.
- no ignition: open-circuit across switch when actuated or broken harness conductor.
- Continuous sparking: continuity present when switch should be open or leakage to chassis ground.
- Intermittent spark: high-resistance contacts, corroded terminals, or intermittent connector seating.
| item | Description |
|---|---|
| Continuity (closed) | Near 0 Ω across switch terminals when actuated (indicates closed contact) |
| Open (off) | Infinite/OL across switch terminals when in off or rest position |
| Ground leakage | Any measurable continuity between terminal and chassis indicates leakage or short |
Replacement Considerations and Stepwise Installation Procedures for the 316580615 Switch and Wire Harness
The 316580615 Frigidaire range Spark Ignition Switches with Wire Harness serve as the operator interface and low-voltage control link between the range control knobs and the spark/ignition module. The rotary or momentary-contact switch closes a circuit that signals the ignition module to produce high-voltage pulses to the burner igniters; the attached harness provides the correct pinout, insulation, and length so the switch can be mounted in the control panel and routed safely away from heat sources. Common failure modes include worn contact faces that show no continuity when actuated, broken conductor strands inside the harness, or corroded connector terminals that produce intermittent sparking or continuous clicking; confirm compatibility by matching connector shape, wire colors, and pin mapping to the original assembly before installation.
- Disconnect mains power and gas supply before any disassembly.
- Remove the control panel or backguard screws to access the switch and harness; photograph and label existing wire locations for reassembly.
- Use a multimeter to check switch continuity in the actuated position and to verify harness conductors are not open or shorted to chassis ground.
- Release retaining clips or screws, unplug factory connectors, and transfer any mounting hardware or insulating sleeves to the new assembly.
- Route the new harness following the original path, secure with supplied clips, connect like-for-like terminals, then re-test continuity and the ignition sequence before final reassembly.
| Item | Description |
|---|---|
| Tools | Screwdrivers,multimeter,needle-nose pliers,and small torque driver for panel screws |
| Electrical checks | Continuity across closed switch (near 0 Ω),harness open/short checks,and verify low-voltage control feed (line voltage to module per manual) |
| Connector mapping | Match wire colors and pin positions; some models use keyed housings to prevent miswiring |
Practical installation considerations include ensuring the replacement switch and harness have adequate insulation and strain relief so vibration and heat do not abrade conductors over time. If the ignition still fails after installing a verified-good 316580615 switch and harness, inspect the igniter electrodes for grounding or erosion, confirm the spark module receives the expected control signal, and check the gas valve/orifice for fuel flow issues; replacing the switch does not correct faults in downstream components. For reliable service, document pinouts and take measurements before disassembly so testing after replacement is limited to verification rather than troubleshooting unknown wiring changes.
Q&A
What is the 316580615 Frigidaire Range Spark Ignition Switch with Wire Harness and what does it do?
The 316580615 is an OEM-style spark ignition switch assembly that includes the electrical switch and a short wire harness used on many Frigidaire/Frigidaire Gallery/Kenmore gas ranges. The switch routes line voltage to the burner igniter when a control knob is turned to the “light” position, allowing the spark module/igniter to produce a spark to light the gas.
How do I know if the ignition switch or harness is bad?
Common symptoms include: one or more burners won’t produce a spark, constant clicking without ignition, intermittent sparking, visible burning or melted insulation on the harness, or a knob position that no longer activates the spark. If only the switch controls one burner and that burner fails to spark while others work, the switch or its wiring is a likely cause.
Can I test the ignition switch with a multimeter? If so, how?
Yes.First unplug the range or disconnect power. Remove the control panel to access the switch. For continuity testing, set the meter to continuity/ohms and check between the common terminal and the switched terminal while actuating the switch (turning the shaft to the “ignite” position). You can also check for proper voltage (carefully) by restoring power and measuring AC between the common and the switched terminal while a helper turns the knob to the ignite position-only do this if you are experienced and take appropriate electrical safety precautions (live voltage is present).
How do I replace the 316580615 ignition switch and wire harness?
turn off power to the range and shut off the gas for safety. Remove the control knobs, access the control panel or console, and locate the switch/harness assembly. Disconnect the harness connectors (take photos or label wires before disconnecting), remove mounting screws, and pull out the old switch. Install the new switch in the same orientation, attach the harness connectors as labeled or per yoru photos, secure the switch, replace the control panel and knobs, restore power, and test.Follow the manufacturer’s service instructions for your model; if you’re not cozy working with gas/electric connections, hire a qualified technician.
Do I have to replace the entire wire harness or can I just swap the switch?
It depends. If only the switch body has failed and the harness and connectors are undamaged, you can replace just the switch. However, harness insulation and connectors age and can be brittle or damaged; many technicians prefer replacing the switch with a new harness (or a combined assembly like 316580615) to ensure reliable connections and correct wire length/terminals.
How do I make sure the replacement part fits my specific Frigidaire model?
Verify compatibility by checking your range’s model number (usually on the frame behind a drawer or on the back panel) and comparing it to the part listing on the manufacturer or parts distributor website. Match connector types, mounting holes, and shaft diameter/length. If in doubt,provide the model number to the parts supplier or consult Frigidaire’s official parts diagram for your model.
What precautions should I take when working with the ignition switch?
Always disconnect power before handling the switch or wiring. Shut off the gas supply when opening areas near gas valves or burners. Avoid forcing connectors-use proper tools, label wires, and keep metal objects away from energized terminals. After replacement, check for proper spark operation and verify there are no gas leaks before regular use. If you detect damaged wiring, scorched terminals, or you smell gas and cannot isolate the source, stop and contact a qualified technician.
Will replacing this switch fix electronic ignition problems caused by the igniter module or spark electrode?
Not always.The 316580615 assembly addresses the mechanical/electrical switch and harness that sends power to the igniter. If the spark module, igniter electrode, or high-voltage wiring beyond the switch is defective, replacing the switch may not restore ignition. Diagnose by isolating components: verify the switch provides voltage when actuated, check spark module output, and inspect electrodes for damage. Replace the specific failing component(s) as identified.
Closing Remarks
The 316580615 Frigidaire range Spark Ignition Switch with Wire Harness serves a critical role in initiating and maintaining reliable burner ignition on Frigidaire ranges.By providing the electrical switching required to create a spark at the burner and a matched harness for consistent connections,this component directly affects appliance safety,ignition consistency,and overall cooking performance. Proper operation of the switch and harness reduces the likelihood of delayed ignition, repeated sparking, or unburned gas accumulation, helping the range operate as intended.
Timely and accurate diagnosis followed by appropriate replacement when faults are identified preserves safety and prevents further appliance damage. Confirming symptoms, testing the switch and wiring for continuity, and using the correct 316580615 replacement part help ensure proper fit and function. Because ignition systems involve both electrical and gas-related hazards,professional assessment or installation is advisable when there is any uncertainty. Correct diagnosis and replacement restore dependable operation, extend service life, and maintain safe use of the range.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok