WB16K10026 GE Oven Range Stove Cooktop Double Burner is a surface heating element assembly designed for use on electric GE ranges and ovens. It is indeed a dual concentric (double) burner unit that provides two selectable heating zones within a single physical element, and typically includes the heating coils or radiant element, mounting hardware and terminal connections required to secure it to the cooktop. As a discrete replaceable component, it functions as the primary heat source for one cooktop location and is classified as a field-replaceable surface element assembly in service documentation.
Within the appliance the double burner converts incoming mains electrical power into heat and interfaces directly with the range’s control system-typically an infinite/element switch or electronic control board-and the cooktop wiring harness. Its terminals receive switched line voltage and the element’s impedance determines the heat output for each concentric zone; the control system modulates energy to the inner or outer circuit to provide different power settings. The burner also interacts indirectly with protective and grounding circuits: poor connections or insulation breakdown can produce arcing, trip overcurrent protection or create a safety hazard, while an open element will prevent heating at that cooktop location.
In the article that follows you will find a technical description of the WB16K10026’s intended function and construction,guidance on model compatibility and terminal/mounting variations to watch for,common failure symptoms (open circuits,intermittent heating,visible damage,short-to-ground and connection faults),step-by-step troubleshooting checks (visual inspection,continuity/resistance testing,and voltage verification at the element terminals),and practical replacement considerations (correct part selection,terminal type and orientation,safe power isolation,and post-repair verification). The guidance is presented for technicians, engineers and competent appliance owners as a practical aide to diagnosis and safe replacement; refer to the specific appliance service manual for exact resistance values and model-specific procedures.
Table of Contents
- function and Role of the cooktop Double Burner Assembly
- How the WB16K10026 GE oven Range Stove Cooktop Double Burner Works Inside the Appliance
- Common failure Symptoms and Diagnostic indicators for the Cooktop Double Burner
- Compatibility, Replacement Considerations, and Installation Guidelines for the Double Burner Assembly
- Q&A
- In Summary
Function and Role of the Cooktop Double Burner assembly
The WB16K10026 GE Oven Range Stove Cooktop Double Burner is a packaged cooktop heating assembly that provides two adjacent heating zones and the mechanical support and electrical terminations required to integrate them into the range control system. The assembly typically contains two heater elements mounted to a support plate, insulated terminal connections or a small terminal block, and the mounting points that align with the factory cooktop openings. Technicians should verify that the terminal layout and mounting hole pattern match the appliance before replacement; correct installation requires matching the voltage rating and connector type to the range’s infinite switches or electronic control outputs.
In operation each element draws current through its control device and converts electrical power to heat; differences in element size or power rating will produce different heat-up and cool-down characteristics for each zone. Common failure modes are open-circuit elements, high-resistance connections at the terminals, and mechanical deformation that prevents full seating in the cooktop cutout. for practical troubleshooting, isolate the assembly from the control, inspect terminals for corrosion or arcing, and check element continuity with a multimeter; when replacing the assembly, confirm physical fit and terminal correspondence to avoid mis-wiring or overloading the control circuit.
- Features: two autonomous heating zones, integrated mounting plate, factory-style terminals
- Symptoms of failure: one zone cold, intermittent heating, visible arcing at terminals
- diagnostic checks: visual terminal inspection, continuity/resistance measurement, verify mounting alignment
| item | Description |
|---|---|
| part | WB16K10026 GE Oven Range Stove Cooktop Double Burner assembly |
| Function | Provides two heater elements and required mounting/terminals for cooktop zones |
| Compatibility | Match voltage, terminal configuration, and mounting pattern to the GE range model |
How the WB16K10026 GE Oven Range Stove Cooktop Double Burner Works Inside the Appliance
The WB16K10026 GE Oven Range Stove Cooktop Double Burner is a concentric surface element assembly that contains two independently controlled resistive heating circuits. Internally the part is formed as an inner and outer coil that share a common mounting flange and separate spade terminals; the range’s surface-element selector (infinite) switch or electronic controller connects power to one or both coils to vary effective heating area. When energized, current flows through the selected coil resistances and converts electrical energy to heat; heat distribution and effective wattage depend on which circuit(s) are active, the coil resistance, and the line voltage supplied by the range.
functionally the double burner behaves as two switchable resistive loads, so common failure modes are open windings, high-resistance terminal connections, or intermittent contact at the switch. Technicians should verify continuity and measure cold resistance to estimate expected wattage at nominal line voltage (typically 240 V across the two hot legs in North American ranges) and inspect the spade terminals and mounting clips for corrosion or distortion.Replacement compatibility requires matching terminal arrangement, flange diameter, and wattage; for example, an outer-ring failure will still permit heating on the inner ring but will reduce effective cooking area and power for large cookware, whereas an open inner coil will prevent small-pot heating even if the outer ring still works.
- Independent circuits: inner and outer coils selectable by the control
- Electrical connection: standard spade terminals, common mounting flange
- Common symptoms: no heat on one ring, intermittent heating, visible arcing or burned terminals
- Diagnostic checks: continuity/resistance measurement and visual inspection of terminals and insulation
| Item | Description |
|---|---|
| Inner circuit | Smaller diameter coil used for concentrated heat; separate terminal for control |
| Outer circuit | Larger ring providing greater surface coverage; energized alone or with inner coil |
| Terminals | Spade connectors; maintain secure, corrosion-free connections for reliable operation |
| Typical testing | Measure cold resistance with a multimeter and compare to expected values; check for open circuit |
| Mounting/fit | Match flange size and terminal layout to ensure mechanical and electrical compatibility |
Common Failure Symptoms and Diagnostic Indicators for the Cooktop Double Burner
The WB16K10026 GE Oven Range stove Cooktop Double Burner is a dual-ring heating element assembly designed to provide two concentric heat zones on compatible GE electric ranges. Functionally,the assembly switches power between the inner and outer coils to allow a user-selectable cooking area and heat output; the part consists of resistive heating elements,insulating supports,and terminal connections that mate to the cooktop wiring harness and infinite switch. Understanding the physical layout and how the inner and outer circuits are energized is essential when interpreting symptoms,as a failure can be isolated to one coil,the shared terminal,or the control selector rather than the entire assembly.
Diagnosing faults on the WB16K10026 GE Oven Range Stove Cooktop Double Burner relies on a combination of visual inspection and electrical measurement. Technicians typically check for continuity across each coil with a multimeter, inspect terminals and harnesses for loose or corroded contacts, and observe heating behavior during a controlled test cycle; for example, an inner coil that never heats while the outer coil functions usually indicates an open inner coil or broken connection at the shared terminal, whereas intermittent heating or arcing points to a loose connector or damaged insulation. Verify mechanical compatibility-mounting tab locations and terminal spacing-before replacement,and confirm that symptom patterns (no heat,reduced heat,uneven zones,or arcing) correspond to either the element,the infinite switch,or wiring to avoid unneeded part swaps.
- No heat on one zone: suggests open coil or broken internal lead-measure continuity separately on inner and outer terminals.
- Reduced or uneven heat: may indicate increased resistance from a partially damaged coil or poor terminal contact-measure resistance and inspect connections.
- Intermittent heating or visible arcing: frequently enough caused by loose terminals, burned connectors, or insulation failure-inspect for discoloration and test under load carefully.
- clicking or selector issues with normal element readings: points toward the infinite switch or control circuitry rather than the element itself.
| Item | Description |
|---|---|
| Continuity check | Confirm closed circuit on each coil at ambient temperature; open reading indicates a failed coil. |
| Terminal inspection | Check for corrosion, loose lugs, or heat damage at the element-to-harness interface. |
| Compatibility | Ensure terminal spacing and mounting tabs match range model; WB16K10026 is a direct-fit for specified GE cooktop models. |
compatibility, Replacement Considerations, and Installation Guidelines for the Double Burner Assembly
The WB16K10026 GE Oven range Stove Cooktop Double Burner is a replaceable heating element assembly that provides two concentric heating zones for varied cooking power.It mounts into the cooktop cutout and connects to the range’s infinite switch or terminal block; the assembly’s behavior depends on correct terminal type, element diameter, and wattage rating. Technicians should compare the replacement to the original part number and visually verify the number and shape of terminals (spade, screw, or harness), the location of mounting tabs, and the outer ring diameter so the element seats correctly under the cooktop and aligns with the control knob’s range of heat outputs.
Installation requires basic electrical troubleshooting and mechanical transfer of any retainers or trim pieces from the old element. Before starting, disconnect power at the breaker and confirm zero voltage with a meter; then remove the cooktop or access panel, disconnect the element terminals, and check the replacement for continuity and insulation resistance to chassis ground. After mounting and reconnecting, test on low power to confirm correct switching behavior and absence of arcing; if the element shows no continuity or shorts to ground, verify wiring harness compatibility and infinite switch ratings before energizing further. For complex wiring harnesses, control replacements, or uncertain compatibility, consult the appliance service manual or use a qualified technician to avoid damage to controls or risk of electrical fault.
- Compatibility checklist: terminal type, element diameter and ring configuration, mounting tab positions, nominal voltage/wattage, and harness connector style.
| Item | Description |
|---|---|
| Voltage | 240/208 VAC nominal for most household electric ranges |
| Connection | Spade terminals or range-specific harness; confirm pin layout before replacement |
| Mounting | Cooktop-mounted with tabs/retainers; dimensions must match cutout and trim |
| Common symptom | Intermittent heating,no heat,or arcing at terminal indicating failed element or poor connection |
Q&A
What is the WB16K10026 part?
WB16K10026 is a GE replacement surface heating element (a double/dual burner coil) used on certain GE electric ranges/cooktops. It contains inner and outer heating zones in a single assembly so you can heat with either or both zones. To confirm fitment for your stove, match the part number to your range model using the GE parts diagram or the label on your appliance.
How do I determine whether the WB16K10026 element is faulty?
Start with a visual inspection: look for breaks,burn marks,heavy corrosion,or a warped coil.Then disconnect power and use a multimeter: check for continuity across the element terminals - a good element will show a low resistance (typically in the low tens of ohms, depending on wattage); an open (infinite) reading means the element is broken. Also check for a short to ground by measuring between each terminal and the element chassis/ground – a low resistance here indicates leakage and a bad element.
Can I replace the WB16K10026 myself and what are the basic steps?
Yes,many owners can replace it,but always disconnect the range from electrical power first (turn off the breaker or unplug). Typical steps: (1) pull the range away and access the cooktop or terminal area, (2) remove the retaining hardware or outlet that holds the coil, (3) note and/or photograph terminal/wire positions, (4) disconnect the spade connectors from the element, (5) install the new element in the same orientation and reconnect the wires, and (6) restore power and test. Take care around sharp sheet metal and live terminal blocks; if you are uncomfortable with electrical work, hire a qualified technician.
How can I tell whether the element or the infinite/control switch is the problem?
If the element has continuity but does not heat, the infinite/control switch or the wiring/terminal connections may be faulty. With the element confirmed good, a technician can measure if the switch is supplying voltage to the element when a heat setting is selected (use proper live-voltage precautions). Another practical check is to swap the element or switch with a known-good identical position (if available) to isolate the failed component. If you aren’t experienced with live voltage testing, call a technician.
Why is the element arcing or sparking when I turn it on?
Arcing is usually caused by a cracked or damaged coil, exposed wiring, a short between the element and the cooktop/frame, or foreign conductive debris contacting the hot coil. It can also result from a damaged receptacle or loose terminal connections. Immediately stop using the burner, disconnect power, and inspect for visible damage. Replace the element and/or repair the receptacle or wiring as required.
How do I verify the correct replacement (size/wattage/terminal configuration)?
Do not rely solely on appearance. Verify compatibility by cross-referencing the part number (WB16K10026) with your stove’s model number using the manufacturer’s parts list or an authorized parts supplier. Confirm the physical dimensions (coil diameter), terminal type/number of spade connectors, and the listed wattage/specs on the part listing. If your cooktop uses a dual-zone (inner/outer) control, ensure the replacement supports the same terminal configuration.
Do I have to replace both double burners if one zone stops working?
No – you can replace only the defective element assembly. However, if the other element or the cooktop receptacle shows wear, or if the range is older, you might consider replacing adjacent elements or the receptacle for long-term reliability. Always investigate the receptacle and wiring before installing a new element to avoid repeated failures.
What maintenance and cleaning practices help the WB16K10026 last longer?
Allow the element to cool before cleaning. Wipe spills off the coil and surrounding drip pan after use with a damp cloth; avoid abrasive scouring pads that can damage finish or insulation.Don’t run an empty element for extended periods, and avoid dragging heavy cookware that can deform the coil. Inspect periodically for corrosion, loose terminals, or damage and address problems promptly to prevent arcing or failure.
In Summary
The WB16K10026 GE Oven Range Stove Cooktop Double Burner serves as an essential heating component for compatible GE ranges, supplying the consistent and controllable heat needed for everyday cooking tasks. As an original equipment manufacturer (OEM) replacement part, it plays a direct role in maintaining appliance performance, energy efficiency, and user safety by restoring proper heating function on affected cooktop zones.
Accurate diagnosis is important before pursuing replacement: identifying the root cause of uneven heating, non‑functioning elements, or other symptoms ensures that replacing the burner is the appropriate remedy. When replacement is needed, using the correct part and following manufacturer installation guidance-or engaging a qualified service technician-helps ensure the repair is effective and maintains appliance safety and warranty considerations.
the WB16K10026 double burner is a key component for maintaining reliable cooktop operation. Thoughtful assessment and timely, proper replacement when warranted will help restore functionality, prolong the service life of the range, and uphold performance and safety standards in the kitchen.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok