240351240 Frigidaire Refrigerator Crisper Pan is a molded interior component that functions as the support and containment tray for the crisper drawers in select Frigidaire refrigeration models. It is typically an injection-molded thermoplastic part shaped too accept the vegetable/fruit drawers and to interface with the drawer slides,cabinet ribs,and adjacent interior liners. As a serviceable OEM component, it is identified by the part number for accurate fitment and replacement and is commonly found in the lower fresh-food compartment behind the refrigerator door.
Within the appliance, the crisper pan provides mechanical support for the drawers, establishes sealing surfaces that influence compartmentalized airflow and humidity control, and acts as a containment area for liquid spills and produce moisture. It interacts indirectly with the refrigerator’s air distribution system and thermostat by helping to maintain the intended microclimate around stored produce; it also engages with mechanical systems such as drawer glide rails, retainers, and any integrated humidity-control dampers. Damage, warpage or improper seating of the pan can create air leaks, alter local temperature and humidity, impede drawer operation, and contribute to frost or condensate accumulation that affects overall performance.
In the article you will find a technical review of the 240351240 crisper pan covering its function and design intent, model compatibility and identification tips, common failure modes and diagnostic symptoms, step‑by‑step troubleshooting checks, and practical replacement considerations. Guidance will include inspection points to verify fit and sealing, interaction checks with adjacent components (glides, dampers, liners), recommended tools and safe removal/installation practices, and verification steps to confirm restored operation after replacement. The focus is practical, technical information to support accurate diagnosis and repair without prescriptive marketing claims.
Table of Contents
- Function and Role of the Crisper Pan in Refrigerator Humidity Control and Produce Preservation
- How the 240351240 Frigidaire Refrigerator Crisper Pan Integrates with Internal Airflow, Rails, and Seal Systems
- Common Failure Symptoms and Diagnostic Indicators for Leaks, Warping, and Seal Degradation
- Compatibility, Replacement Considerations, and Step-by-Step Installation for the 240351240 Frigidaire Refrigerator Crisper Pan
- Q&A
- The Conclusion
Function and Role of the Crisper Pan in Refrigerator Humidity Control and Produce Preservation
The 240351240 Frigidaire Refrigerator Crisper Pan serves as the structural base for the refrigerator crisper drawer and as a controlled moisture reservoir that affects local humidity around stored produce. Mounted under the crisper drawer,the pan captures condensation and incidental spills,and its geometry and fit into the cabinet reduce convective air exchange between the drawer and the main compartment; this reduced airflow helps maintain a higher relative humidity inside the drawer when the drawer is closed. The pan is typically injection-molded plastic (commonly ABS or polypropylene) and, in compatible Frigidaire models, incorporates channels or a drain alignment feature that routes defrost or condensate water toward the refrigerator’s drain system rather than allowing it to accumulate under the drawer.
From a practical maintainance and compatibility standpoint,the crisper pan’s condition and installation directly influence produce life and humidity control performance. A properly seated pan creates the intended seal and drainage path; cracks, warpage, or misalignment can allow dry cabinet air to infiltrate the drawer or cause standing water that increases spoilage and odors. For appliance technicians and owners,routine inspection for structural damage,ensuring the drain alignment is unobstructed,and periodic cleaning with mild detergent preserve function. Examples: storing leafy greens in the sealed drawer over the pan retains moisture and slows wilting, while leaving the drawer improperly seated can accelerate dehydration of greens or uneven ripening of fruits.
- Key behaviors: moisture capture, airflow reduction under the drawer, drainage channeling.
- Common failure signs: visible cracks, persistent water pooling, unusual odors, loose seating.
- Maintenance actions: clean pan surfaces, verify drain alignment, replace if warped or cracked.
| Item | Description |
|---|---|
| part number | 240351240 Frigidaire Refrigerator Crisper pan (replacement part identification) |
| Material | Injection-molded plastic (commonly ABS or polypropylene) |
| Location | Under crisper drawer in lower refrigerator compartment |
| Function | Collects condensate/spills, maintains drawer humidity by limiting airflow, provides drainage alignment |
| Compatibility | Fits select frigidaire refrigerator models; verify model number for exact fit |
How the 240351240 Frigidaire Refrigerator Crisper Pan Integrates with Internal Airflow, Rails, and Seal Systems
The 240351240 Frigidaire Refrigerator Crisper pan functions as both a drawer support and an airflow-routing element inside the crisper compartment.Its molded geometry (lip,notches,and vent passages) sits on the internal rails and establishes the relative gap between the crisper cavity and the refrigerator evaporator ducting. Rather than forming an airtight seal,the pan’s edges and mating surfaces cooperate with the cabinet seals and drawer glides to channel cold air through designated vents,maintain a localized microclimate for produce,and limit cross-flow that would otherwise equalize temperatures between compartments. The pan’s material and thickness also affect thermal conduction and condensate behavior at the interface where cold air meets warmer interior surfaces.
When servicing or replacing this component, verify that the pan correctly engages the rails, that the pan-to-cabinet contact points compress against the surrounding seals, and that the vent openings remain unobstructed; improper seating commonly causes uneven cooling, frost accumulation near the evaporator, or water pooling in the drawer. Technicians should inspect rail alignment, notch orientation, and seal contact surfaces during installation and use the part number to confirm geometric compatibility with the refrigerator model. Practical examples include swapping a pan from a different model that appears to fit but blocks a vent port (leading to warmer crisper temperatures) and replacing a cracked pan that permits excessive air exchange and rapid moisture loss from stored produce.
- Inspection checkpoints: rail engagement, notch alignment, vent clearance, seal contact integrity, and pan flatness.
- Common symptoms of improper integration: uneven crisper temperature, ice buildup near vents, and water pooling in the drawer.
| Item | Description |
|---|---|
| Material | Rigid thermoplastic with low thermal conductivity to reduce rapid heat transfer and condensation points |
| Mounting interface | Upper lip and locator notches that sit on refrigerator rails and position vent passages relative to ducting |
| Role in airflow | Directs cold air through vents and limits cross-flow between crisper and main cavity; does not create an airtight seal |
| Compatibility check | Confirm by matching part number and verifying rail/gasket geometry; visual fit alone can be misleading |
Common Failure Symptoms and Diagnostic Indicators for Leaks, Warping, and Seal Degradation
The 240351240 Frigidaire Refrigerator crisper Pan functions as the structural basin beneath the crisper drawer and as a controlled-moisture surface that collects condensate and spilled liquids. Performance problems typically arise from physical damage (hairline cracks, fractures, or warped planes), mating-surface misalignment with the drawer gasket, or progressive seal degradation where the pan no longer forms an adequate barrier against airflow and liquid migration. Technicians should consider both mechanical fit and material condition: a slightly warped pan can lift a gasket edge by a few millimeters and instantly change local humidity and frost patterns, while a crack that holds water intermittently will create localized corrosion, odors, and drip-through onto lower compartments.
- Pooling of water beneath or around the crisper – suggests cracked pan or blocked drains.
- Drawer not seating flush or uneven resistance – indicates warping or damaged mounting tabs.
- excessive condensation or frost on produce – consistent with seal degradation or air leaks.
- Visible cracks, stress lines, or brittle plastic at corners – material fatigue leading to leaks.
- Persistent odors after cleaning – trapped moisture in damaged pan areas or inaccessible crevices.
| Item | description |
|---|---|
| Pooling under drawer | Often caused by a crack or blocked drain channel; remove pan and perform a water-fill test to localize leak. |
| Drawer misalignment | Warped pan or broken mounting tabs; measure flatness and inspect rail engagement before replacing part. |
| Increased frost/condensation | Seal compression loss or edge gap; inspect gasket interface and perform a humidity/temperature comparison across compartments. |
For practical diagnosis,perform a visual inspection followed by simple functional tests: remove the crisper assembly and place the pan on a certified flat surface to check for gaps or rocking,pour a measured amount of water into suspected areas to observe seepage,and verify that drawer rails engage with the pan’s mounting features without binding. Use the outcomes of thes tests to decide whether a replacement is required (cracked or irreversibly warped pan) or if targeted repairs (gasket replacement, clearing a drain channel) will restore proper function. Document compatibility and fit during replacement to ensure the replacement part restores the original seal geometry and humidity behavior rather than introducing a new source of air or liquid leakage.
compatibility, Replacement Considerations, and Step-by-Step installation for the 240351240 Frigidaire refrigerator Crisper Pan
The 240351240 Frigidaire Refrigerator Crisper pan is the flat support surface installed beneath the crisper drawer that captures spills and routes condensate toward the refrigerator drain. Functionally it transfers load to the drawer slides, maintains the correct drawer height for humidity-control seals, and resists moisture exposure; common constructions are tempered glass or reinforced thermoplastic.Compatibility depends on the pan’s footprint and the location of molded rails or locating tabs-measure the pan length, width, thickness, and the center-to-center spacing of any mounting ribs, and compare those dimensions with the refrigerator’s parts diagram or service manual before ordering a replacement.
Replacement requires inspection of the drawer slides, retaining clips, and the drain area for debris or damage; a cracked pan or broken tabs will impair drawer alignment and humidity performance. Typical installation is a simple mechanical procedure: remove the contents and drawer, lift the old pan out, clean the track and drain area, seat the replacement pan into the rear locating features, reinstall the drawer and verify smooth travel and engagement. Minimal hand tools are usually needed (a screwdriver for retaining clips on some models); avoid forcing the pan into misaligned rails, and confirm the drain path remains unobstructed after reassembly.
- Unload and remove the crisper drawer by sliding it out and tilting to release retaining lips.
- Lift the pan from the rear locating tabs and slide forward to remove; inspect for cracks and worn tabs.
- Clean the track, remove debris from the drain channel, and replace any damaged clips or rails.
- Engage the rear locating features of the new pan, lower the front into the track, then slide the drawer back in and test for smooth operation.
| Item | Description |
|---|---|
| Typical material | Tempered glass or high-density ABS plastic resistant to cold and moisture |
| Key dimensions | Match cabinet footprint and rail spacing; measure length × width and rail center-to-center |
| Common failure modes | Cracks, warped rails, broken locating tabs, and accumulated debris obstructing drain |
Q&A
What is Frigidaire part 240351240?
Part 240351240 is listed as a replacement crisper pan/drawer pan used in certain Frigidaire (and related Electrolux) refrigerators. It is the removable pan that sits under the crisper/vegetable drawer and collects spills or excess moisture. Always confirm the part number against your refrigerator model before ordering.
How do I check if 240351240 fits my refrigerator?
Locate your refrigerator model number (usually on a sticker inside the fresh-food compartment, on the door frame, or on the back). Use that model number to search Frigidaire’s parts lookup or provide it to an authorized parts dealer. Cross-reference the OEM part number 240351240 and compare dimensions and mounting features to ensure a correct fit.
How do I remove and install the crisper pan?
Typical procedure: remove any produce, pull the crisper drawer forward until it clears the stops, lift the drawer slightly to release it from the rails and slide it out. Lift the pan out of the drawer or slide it off its supports (depending on design). To install, reverse the steps-position the pan on the rails, insert the drawer and push it back until it seats. No special tools are normally required; if you encounter clips or stops,check for small retaining tabs that need to be depressed to remove the drawer.
Why does water or condensation collect in the crisper pan?
Some condensation is normal because warm air and moisture enter the compartment when the door is opened. Excessive water can be caused by: high humidity in the crisper due to full drawers, clogged or blocked air vents preventing airflow, a faulty door gasket or door left ajar, improper temperature settings, or a defrost/drain issue. Inspect seals and vents,adjust humidity controls and temperature,and unclog any drain channels. If condensation persists,have the refrigerator’s defrost/drain system and temperature sensors checked.
Can I put the crisper pan in the dishwasher?
It depends on the material. Many pans are made of plastic or tempered glass; some tempered glass pans might potentially be dishwasher-safe on the top rack, while some plastics can warp from high dishwasher heat. The safest approach is to hand-wash with warm soapy water and a non-abrasive sponge. Avoid harsh chemicals and abrasive pads that could scratch or damage the part. Check the part description or manufacturer’s care instructions if available.
What should I do if the replacement pan doesn’t fit correctly?
First confirm you received the correct OEM part number for your model. Compare mounting tabs, drawer width, and overall dimensions with the old pan. Check the drawer rails and stops for damage or debris that could prevent seating. If the part is the correct number but still won’t seat, inspect for broken tabs on the pan or drawer and for alignment issues. Contact the seller or Frigidaire parts support for a replacement or further troubleshooting.
Is it safe to use a cracked or chipped crisper pan?
No. Do not use a cracked or significantly chipped pan-glass can shatter and plastic can leak or cut produce; both create hygiene and safety risks. replace the pan with the correct part number.If the damage occurred shortly after purchase, check warranty/return options with the seller or manufacturer.
Where can I buy a genuine 240351240 replacement and is there a warranty?
You can buy this part from Frigidaire’s official parts website, authorized appliance parts dealers, or reputable online retailers.When buying,prefer listings that specify “OEM” or “Genuine Frigidaire” and show compatibility with your refrigerator model. Warranty varies by seller-OEM parts often come with a limited warranty through the manufacturer or reseller; verify the return policy and warranty coverage before purchase.
The Conclusion
The 240351240 Frigidaire refrigerator crisper pan serves as an essential internal component designed to support and protect fresh produce while helping to manage moisture and containment within the crisper compartment. By providing a stable, easy-to-clean surface and helping to channel condensation, the pan contributes to consistent humidity control, reduces the risk of spills and cross-contamination, and supports overall appliance efficiency and food preservation.
Proper diagnosis and timely replacement of a damaged or worn crisper pan are critically importent to maintain those benefits. Regular inspection for cracks, warping, drainage blockages, or fitment issues can identify problems early; when a pan is compromised, replacing it with the correct 240351240 part or an equivalent OEM-approved piece helps restore intended fit and function. Whether replacing the pan yourself or seeking professional service, accurate model matching and correct installation ensure continued refrigerator performance and can prevent food spoilage or secondary damage to other components.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok