137006900 Frigidaire washer Strike is a service part that functions as the door/lid strike or catch within Frigidaire laundry appliances. As a discrete mechanical component, the strike provides a fixed engagement point for the door or lid latch; it is typically a molded plastic or stamped metal piece mounted to the washer cabinet were the door closes and aligns with the latch assembly.
Inside the appliance, the strike’s primary role is mechanical engagement and actuation: when the door closes the latch mates with the strike to secure the door and, in many designs, to actuate the door-closed interlock or switch that permits the control system to proceed with a cycle. The strike thus interacts directly with the latch or lock mechanism, the door hinge and seal alignment, and indirectly with the control board and safety interlock circuitry. Proper fitment, orientation, and wear resistance are critically important as misalignment or damage to the strike can prevent correct latch engagement, cause false open-door signals, or allow water and vibration to affect cycle operation.
This article will explain the 137006900 strike’s intended function and typical locations of use on Frigidaire washers,describe compatibility considerations across models,and list common failure symptoms such as a washer that will not start,stops mid-cycle,or exhibits door-latch difficulties. It will also cover practical troubleshooting checks (visual inspection, alignment verification, and basic electrical verification where applicable) and outline replacement considerations including correct part orientation, mounting fasteners, and post-replacement verification steps a technician, engineer, or appliance owner shoudl perform.
Table of Contents
- Function and Role of the Door Strike in Frigidaire Washer Latch and Safety Systems
- How the 137006900 Frigidaire Washer Strike Integrates with the Door Lock Mechanism and control Circuitry
- Common Failure Symptoms and diagnostic Indicators of a Faulty Washer Strike
- Replacement Considerations, Model Compatibility, and Installation Procedures for the 137006900 Strike
- Q&A
- The Conclusion
Function and Role of the Door Strike in Frigidaire Washer Latch and Safety Systems
The 137006900 Frigidaire Washer Strike is the cabinet-mounted receiver that the door latch tongue engages to secure the front door and provide mechanical input for the washer’s safety interlock. When the door closes the latch tongue inserts into the strike; that insertion provides two functions: mechanical engagement to hold the door under shear and centrifugal loads during spin, and precise actuation of the door-sensing mechanism (microswitch or contact) so the control board can enable motor and heater outputs. Correct operation depends on dimensional accuracy, secure mounting, and intact contact surfaces-cracks, deformation, or incorrect positioning prevent full seating and commonly produce door-open errors or inhibit cycle start for safety reasons.
- Function: aligns and retains the latch tongue and transmits closure to the interlock sensor.
- Physical features: molded or metal engagement surface, specific screw locations, and narrow depth/angle tolerances.
- Failure symptoms: door will not lock, intermittent trips during spin, or the washer refuses to start.
- Service guidance: verify mechanical fit and alignment before replacing electrical components; replace with an exact-fit strike when recess depth or mounting holes differ.
Compatibility and practical servicing focus on mechanical fit and the resulting sensor signal rather than electronic behavior of the strike itself. Confirm that a replacement matches the original strike geometry and screw pattern because small differences in depth or angle alter how the latch seats; a strike that looks similar can still fail to actuate the interlock if its profile is diffrent. For diagnostics,observe the latch engagement visually,measure recess depth and alignment relative to the latch tongue,and verify the control receives a closed-door signal when the tongue is fully seated-if the signal is absent despite correct seating,inspect the latch/microswitch and wiring rather than the strike housing.
| Item | Description |
|---|---|
| Function | Receives latch tongue, retains the door during cycles, and actuates the door-closed sensor. |
| Common symptom | door-open error, failure to start, or mid-cycle door release due to wear or misalignment. |
| Service tip | Check alignment and mounting torque frist; replace only with an exact-fit part if geometry or mounting points differ. |
How the 137006900 Frigidaire Washer Strike Integrates with the Door Lock mechanism and Control Circuitry
The 137006900 Frigidaire Washer Strike is the receiver portion of the door-latch interface that provides the physical engagement point for the washer door latch and aligns the door to the cabinet. As a mechanical datum, the strike transfers the closure forces into the door-lock assembly and ensures a repeatable seal and alignment so the electrical interlock can operate reliably. Compatibility depends on the door design and mounting pattern: this strike must match the cabinet cutout and latch geometry used on the specific Frigidaire models, so technicians should verify the part number against the machine serial and service manual before replacement to avoid misalignment or improper engagement.
When integrated with the control circuitry, the strike works in conjunction with the latch actuators, microswitches or lock assembly and the control board’s lock-relay/logic. Closing the door engages the latch against the strike and either completes a manual microswitch circuit or allows the lock actuator to reach its latched position; the control board then senses the closed/locked feedback and permits the wash cycle to begin. Electrical or mechanical wear of the strike, loose mounting, or misalignment commonly produces no-start symptoms or door-lock fault codes; practical troubleshooting includes visual alignment checks, verifying mechanical travel of the latch into the strike, and measuring continuity or feedback signals at the door-switch connector before replacing the strike.
- Common symptoms: door will not lock, door-open fault codes, or intermittent locking during spin.
- Swift checks: inspect strike alignment, tighten mounting screws, and verify continuity of the door-switch/feedback circuit with a multimeter.
- Replacement tip: transfer any shims or gaskets from the old strike to maintain original alignment and sealing.
| Item | Description |
|---|---|
| Mechanical role | Registers door latch and absorbs closure loads to maintain alignment for the lock assembly. |
| Electrical interface | Works with microswitches or lock actuators to provide closed/locked feedback to the control board. |
| Common failure mode | Wear or misalignment causing poor contact, false open signals, and fault codes. |
Common Failure Symptoms and Diagnostic Indicators of a Faulty Washer Strike
The 137006900 Frigidaire Washer Strike functions as the fixed mating surface for the washer door latch; it positions and secures the latch so the door interlock can register a closed state and allow fill and spin operations.As a mechanical component,its geometry and mounting tolerance determine whether the latch fully engages the interlock switch or actuator. Common mechanical failures include plastic deformation of the strike face, fractured mounting bosses, or elongated mounting holes that alter engagement depth – any of these change the strike-to-latch relationship and produce operational faults even when the latch assembly itself appears intact. Verify model compatibility before fitting a replacement strike because differences in height, thickness, or mounting pattern will cause misalignment and persistent lock-fail behavior.
- Door will not lock or the washer refuses to start despite the door being closed.
- Washer displays door lock-related error codes or aborts mid-cycle.
- Intermittent locking: door locks sometimes but fails under vibration or spin.
- Audible clicking, buzzing, or repeated attempts to lock without engagement.
- Visible wear, cracked plastic, broken tabs, or excessive lateral play at the strike.
| item | Description |
|---|---|
| Continuity test | With the door closed, manually actuate the strike and measure switch closure at the interlock; a lack of consistent continuity indicates a contact or alignment failure. |
| Mechanical fit | Inspect for cracks, worn edges, or crushed material on the strike face that prevent the latch from seating fully. |
| Alignment tolerance | Check that the strike sits square to the latch path and that mounting holes secure it without play; shim or replace if the engagement depth is out of specification. |
Diagnosis begins with a visual and mechanical inspection: close the door and observe whether the latch engages cleanly, then apply light manual force to the strike area while cycling the control to see if engagement is consistent. If the assembly includes an integrated microswitch or interlock, verify electrical behavior with a multimeter while actuating the strike to distinguish between a failed switch and a purely mechanical misalignment. Practical examples include a strike face worn down so the latch never fully trips the interlock (mechanical) or a brittle mounting boss that flexes under spin loads causing intermittent faults (mechanical leading to intermittent electrical). When tests show deformation or inconsistent switch closure, replacement of the strike – selected for correct model fit – is the appropriate corrective action.
Replacement Considerations, Model Compatibility, and Installation Procedures for the 137006900 Strike
The 137006900 frigidaire Washer Strike is the stationary keeper that the door/lid latch actuator engages to complete the mechanical and electrical interlock required for a wash cycle to start. Functionally, the strike locates the latch so a plunger or hook compresses a microswitch or engages a lock module; wear, plastic deformation, or misalignment of the strike will produce symptoms such as failure to latch, intermittent cycle starts, or audible rattling during agitation. Technicians should diagnose by observing the actuator-to-strike engagement, checking switch continuity with a multimeter while operating the latch, and inspecting the strike geometry for broken tabs, excessive wear, or shifted mounting holes that prevent proper contact with the latch mechanism.
Replacement requires confirming mechanical and electrical compatibility before installation: confirm the strike’s mounting-hole pattern,depth-to-latch distance,and any integrated switch or connector orientation match the machine. Safe replacement procedure includes disconnecting power,removing the access panel to expose the strike,transferring any springs or retainers from the old part to the new one,and verifying free,unobstructed motion of the latch against the new strike before final assembly. After refitting, verify switch continuity with the door in the closed position and run a short diagnostic or drain/spin cycle to ensure the latch remains engaged under load; if the strike requires minor positional adjustment, loosen mounting fasteners, align for smooth engagement (no binding), then torque to service-specified values to avoid cracking the plastic housing.
- Power off and disconnect mains before disassembly.
- Document orientation and mounting positions (photo or marks) before removing old strike.
- Check switch continuity while moving the latch to confirm electrical engagement.
- Reassemble and test with a diagnostic or short cycle to confirm correct operation.
| Item | Description |
|---|---|
| Mounting pattern | Match hole spacing and flange profile to ensure correct latch engagement. |
| Functional interface | Strike depth and face geometry determine actuator compression and switch activation. |
| Common failure modes | Plastic tab breakage, wear from repeated impact, and misalignment from stripped fasteners. |
Q&A
What is the 137006900 Frigidaire washer strike?
The 137006900 is the door strike (or door catch) used on certain Frigidaire washing machines. It is the passive metal/plastic catch mounted in the cabinet frame that the door latch engages to hold the door closed and allow the door lock mechanism to function.
What symptoms indicate the strike is bad or needs replacement?
Common symptoms include the door not latching or staying closed, the washer refusing to start as it reports the door as open, intermittent door lock/fail behavior, visible wear/broken or bent strike hardware, or a misaligned strike that prevents the door latch from engaging. You may also see door-related error codes or the door popping open during a cycle.
how can I test whether the strike (137006900) is the cause of the problem?
Visually inspect the strike for damage, cracks, or bending and check that the door latch aligns and engages with it when the door closes. If the strike looks intact, close the door and try to move the latch-if it slips past or won’t engage, the strike is likely faulty or misaligned. For electrical lock issues, use a multimeter to test the door lock assembly (not the strike) for continuity. If the lock works but the latch physically can’t engage the strike,replace the strike.
Which Frigidaire models use part 137006900 and how do I confirm compatibility?
Part compatibility varies by model and production date. To confirm, locate your washer’s model and serial number (usually on a tag behind the door, on the rim, or on the back) and check the Frigidaire parts diagram or an authorized parts supplier listing for that model. Do not rely solely on visual similarity-verify part 137006900 is listed for your specific model before ordering.
Can I replace the 137006900 strike myself, and what tools are required?
Yes, many owners can replace the strike themselves. Basic tools: screwdriver or nut driver set (usually Phillips or Torx screws), possibly a socket set, pliers, and a flashlight.Procedure summary: unplug the washer,open the door,remove the screws securing the old strike,pull it out and install the new strike in the same position,tighten fasteners,and test door closure and a short cycle.If the strike is behind a front or top panel, you may need to remove that panel-refer to the service sheet for panel removal instructions.
How long does replacement typically take and are there any safety steps?
Replacement typically takes 10-30 minutes for an accessible strike. Safety steps: unplug the washer or turn off power at the breaker before starting work, keep the door propped open when removing parts to avoid trapped fingers, and follow manufacturer instructions for any panel removal. If you are not agreeable working on appliances or panels must be removed that expose electrical components, consider a qualified technician.
Is the strike repairable or should I replace it with a new 137006900 part?
Strikes are usually inexpensive and not designed for field repair; cracked, bent, or worn strikes should be replaced rather than repaired. if the problem is alignment (loose mounting screws), sometimes tightening or repositioning the strike will restore function, but any structural damage warrants replacement with a new OEM or equivalent part.
After replacing the strike, do I need to perform any calibration or clear error codes?
Most washers will recognize a new strike automatically. After replacement, close the door and run a short spin or drain cycle to confirm proper locking and operation. If the washer still shows a door-related error, try resetting power by unplugging the washer for 1-2 minutes or consult the service mode/diagnostic procedure for your model to clear stored errors.If problems persist, recheck alignment and wiring for the door lock assembly (the electrically actuated part) rather than the strike.
the Conclusion
The 137006900 Frigidaire washer strike is a small but essential component that helps secure the washer door and engage the door latch mechanism during operation.By ensuring the door closes and remains sealed,the strike contributes to proper cycle initiation,prevents water leakage,and supports the appliance’s safety interlocks. Its correct fit and condition directly affect the washer’s reliability and user safety.
Because symptoms of a failing strike-such as a door that will not latch, error codes, interrupted cycles, or visible wear-can resemble other door or lock issues, careful diagnosis is important. Visual inspection,basic functional checks,and confirmation of part compatibility help determine whether the strike is the source of the problem. When replacement is necessary, using the correct 137006900 part or an approved equivalent and following manufacturer installation guidance restores proper operation and reduces the risk of recurring faults.
the 137006900 Frigidaire washer strike plays a key role in safe and effective washer performance. Accurate diagnosis and timely, correct replacement when defects are found maintain appliance reliability and safety; for complex cases or uncertain repairs, consult the washer’s service documentation or a qualified technician to ensure the repair is completed properly.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
The Blincoo Elite 48" Heavy Duty Dog Rope Toy is made for large breeds that love tug-of-war, chewing, and active play. Strong, simple, and fun for powerful dogs.
Shop on TikTok