240351240 Frigidaire Refrigerator Crisper Pan is a molded storage and containment component designed too sit beneath the crisper drawers in compatible Frigidaire refrigerators. It is typically a thermoformed or injection-molded plastic tray that provides a flat support surface for the crisper drawers, incorporates mounting tabs or rails for drawer alignment, and often includes molded channels or a drain path to route condensate or defrost runoff toward the evaporator drain system.
Within the appliance, the crisper pan performs both structural and fluid-management roles. Structurally it supports the weight of the crisper drawers and their contents and interfaces with drawer slides, seals and internal cabinet geometry; functionally it collects spills and condensate from the fresh-food compartment and directs water to the evaporator drain tube and downstream drip pan. Because it sits at the bottom of the refrigerator compartment, the pan also influences local airflow and humidity retention around the produce drawers and can affect the performance of the defrost/condensate removal system if its drain features are blocked, cracked or misaligned.
In this article readers will find a technical examination of the crisper pan’s function, how to confirm compatibility with specific refrigerator models, common failure symptoms (cracks, warping, clogged or misaligned drain channels, and consequent leaks or food spoilage), and practical troubleshooting steps to isolate pan-related issues. The piece will also cover replacement considerations such as verifying OEM part numbers and dimensional fit, inspecting mounting features and seals, and post-installation checks to ensure correct drain routing and drawer operation.
Table of Contents
- Function and Role of the Crisper Pan in Refrigeration Performance and Produce Preservation
- How the 240351240 Frigidaire Refrigerator Crisper pan Interfaces with Internal airflow, Drainage and Shelving Systems
- Common Failure symptoms, Wear Patterns and Diagnostic Indicators of Crisper Pan Malfunction
- Compatibility, Replacement Considerations and Installation Procedures for 240351240 and Compatible Frigidaire Models
- Q&A
- To Wrap It Up
Function and Role of the Crisper Pan in Refrigeration Performance and Produce Preservation
240351240 Frigidaire Refrigerator Crisper Pan serves as the structural base and microclimate controller for the lower produce compartment. Mechanically, the pan supports the crisper drawer and aligns with the drawer slides and sealing lips to isolate the drawer volume from the main refrigerator cavity; correct fitment prevents cold-air leakage and maintains designed airflow channels. Functionally, the pan collects condensate and transient spills, provides thermal mass that dampens short-term temperature swings, and, when paired with a humidity-control vent or sealed drawer, helps maintain higher relative humidity around fresh produce to slow desiccation and enzymatic degradation.
The pan’s behavior affects both preservation and appliance performance: a warped or improperly seated pan changes pressure differentials and can redirect conditioned airflow, increasing compressor run-time or creating cold spots that accelerate vegetable freezing. Technicians should verify material integrity, mounting tab condition, and drip-channel clearance during diagnostics; owners should avoid replacement parts that alter drawer height or block vent passages. Practical indicators of a failing pan include pooled water beneath the drawer, misaligned drawer tracks, or faster-than-expected produce softening. Typical features and compatibility considerations include:
- Material and strength (tempered glass versus molded plastic) affecting load capacity and thermal conduction.
- Mounting tabs and sealing lips that must match refrigerator rail geometry to preserve airflow isolation.
- Drain or condensate channels that must remain clear to prevent pooling under the evaporator area.
- Model-specific dimensions-only correct-fit parts preserve the designed humidity and airflow characteristics.
| Item | Description |
|---|---|
| Primary function | Support drawer, collect condensate, and help maintain localized humidity and temperature stability. |
| Common materials | Tempered glass or high‑impact food‑grade plastic; material choice affects thermal mass and durability. |
| Compatibility check | Confirm physical dimensions and mounting tab locations against the refrigerator model or part number to ensure intended performance. |
How the 240351240 Frigidaire Refrigerator Crisper Pan Interfaces with Internal Airflow,Drainage and Shelving Systems
The 240351240 Frigidaire Refrigerator Crisper Pan is a molded component that serves as both a moisture collection basin and an element of the refrigerator’s internal airflow and shelving geometry. Its molded drain channel and outlet align with the freezer/refrigerator drain path to route defrost and condensation water away from the crisper area; simultaneously occurring, engineered vent slots and peripheral clearances permit controlled flow of cold air from the evaporator across the drawer face so that temperature and humidity gradients remain predictable. When the pan is correctly seated on the shelf rails and the drain outlet is aligned with the cabinet drain, airflow remains laminar across the drawer openings and condensate is directed to the drain tube; misalignment, warped tabs, or blocked vent openings will change flow patterns and can cause local frost buildup, higher humidity in the drawer, or water pooling inside the pan.
Functionally the pan interacts with shelving and drawer systems through its mounting tabs, stop features and drawer-to-pan interfaces, so replacement parts must match the original mounting geometry and drain location to maintain designed airflow and drainage behavior. The pan is typically a moisture-resistant thermoplastic molded to close tolerances; mechanical failures that affect performance are usually limited to cracked basins,deformed tabs,or clogged drain ports. practical inspection and troubleshooting include verifying that the pan sits flush in the shelf rails, that the drain outlet is clear and aligned to the cabinet drain, and that venting slots are not obstructed by improperly sized shelves or stored items-each of which directly affects cooling efficiency and water handling in the crisper area.
- Drain channel: molded outlet to route condensate to cabinet drain
- Airflow slots: openings that permit controlled cold-air flow across drawer fronts
- Mounting tabs & stops: locate the pan on shelf rails and limit drawer travel
- material properties: moisture-resistant thermoplastic designed to withstand temperature cycling
| Item | Description |
|---|---|
| Air baffle / slots | Provide passage for evaporator-cooled air; their position controls circulation over the crisper |
| Drain channel | Molds to align with cabinet drain; directs condensate away from the crisper surface |
| Mounting tabs | Engage shelf rails and ensure correct vertical and horizontal positioning |
Common Failure Symptoms, Wear Patterns and Diagnostic Indicators of crisper Pan Malfunction
The 240351240 Frigidaire Refrigerator Crisper Pan is the molded support and containment tray located beneath the crisper drawer; its primary functions are to collect condensation, maintain a sealed micro-surroundings for humidity control, and provide structural support for the drawer glides and weight of stored produce. In properly functioning systems the pan interfaces with the humidity control slider and seals against the drawer face to limit airflow between the fresh-food compartment and the evaporator area; any breach in this interface (crack, deformation or misalignment) will change local relative humidity, promote accelerated dehydration of produce, or allow water to pool and migrate to adjacent compartments. Technicians should check the pan for material fatigue (brittleness or crazing),distortion from heat or dishwasher exposure,and compatibility with the specific cabinet mounting features – replacement with an incorrect pan can leave gaps that mimic compressor or defrost faults by altering frost patterns on the evaporator.
Common wear patterns are localized stress cracks at the screw bosses and mounting lips, warpage across the pan flange that prevents a continuous seal, and abrasion or gouging where the drawer contacts the pan; these failures produce measurable diagnostic indicators such as uneven drawer travel, persistent water accumulation under the drawer, and rapid changes in compartment humidity when the door is cycled. Inspect the pan visually and by hand: flex the pan to reveal hairline fractures, verify that the pan sits flat on its support rails, and observe evaporator frost distribution during a controlled door-open/close cycle to determine whether air leakage through the pan is present.Practical replacement criteria include visible cracks affecting the seal, a pan that no longer supports the drawer without rocking, or discoloration with embrittlement that indicates imminent fracture.
- Visible pooling of water beneath the crisper or on shelf below
- Drawer sticking or uneven travel due to warped flange
- Rapid produce drying or excessive condensation in crisper
- Hairline cracks or brittleness near mounting points
- Abnormal frost or icing patterns on the evaporator/coils
| Item | description |
|---|---|
| Material | Typically ABS or polyethylene; material affects brittleness and heat tolerance |
| Typical failure mode | Stress cracks at mounting points, flange warpage, surface abrasion |
| Compatibility | Designed for specific frigidaire model families; verify model number before installing |
Compatibility, Replacement Considerations and installation Procedures for 240351240 and Compatible Frigidaire Models
The 240351240 Frigidaire Refrigerator Crisper Pan is a load-bearing, moisture-management component that sits beneath the crisper drawers to collect spills, route condensate to the cabinet drain, and provide a flat support surface for the drawers above. Fitment depends on precise envelope dimensions and tab or notch locations that engage the refrigerator’s internal rails; the pan must align with the cabinet’s rear drain channel and side support rails to function correctly. technicians should confirm compatibility by cross-referencing the OEM part number against the refrigerator model number and by measuring the pan’s overall width, depth and tab spacing – two refrigerators can appear similar but have diffrent rail geometries or drain offsets that prevent interchangeability.
Replacement typically requires no tools but does require inspection of the support rails and mounting clips; broken rails or deformed tabs are common secondary failures that will prevent a correct fit even when using the correct pan. Common installation steps are: remove food and drawers, lift and slide the pan out along the rails, clean the track and drain area, set the replacement pan into the rear drain channel then lower and engage the side tabs until seated, and finally reinstall the drawers and verify smooth travel and proper drainage. Watch for symptoms of incompatibility such as lateral play, a gap at the rear preventing drain alignment, or drawer binding – if any occur, measure tab spacing and rail profiles or replace the damaged support hardware rather than forcing the pan into place.
- Typical installation steps: remove contents and drawers → inspect rails and drain → align rear drain and side tabs → seat pan fully → test drawer movement and drainage.
| Item | Description |
|---|---|
| Critical dimensions | Overall width, depth, and center-to-center tab spacing determine mechanical fit; measure before ordering replacement. |
| Mounting interface | Engages cabinet rails via molded tabs or notches; damaged tabs or warped pans prevent proper seating. |
| Drain alignment | Rear drain hole must align with cabinet drain channel to avoid pooling or leaks; verify during installation. |
| Compatibility check | Cross-reference OEM part number and refrigerator model; identical appearance does not guarantee identical rail geometry. |
Q&A
what is part 240351240 for Frigidaire refrigerators?
Part 240351240 is a replacement crisper pan/drawer sold for Frigidaire refrigerators. it is the removable bin that sits on the crisper rails and holds fruits and vegetables. As with most OEM parts, the exact shape and material are designed to match specific Frigidaire models so the pan fits and slides correctly.
How do I confirm 240351240 will fit my refrigerator model?
Confirm fit by matching the refrigerator model number (found on the interior wall or behind the kickplate) to the parts listing on Frigidaire’s website or a reputable parts supplier. Search the model number in a parts lookup; if 240351240 appears in the parts diagram for your model, it is indeed compatible. Do not rely solely on visual similarity-dimensions and rail engagement points must match exactly.
How do I install the 240351240 crisper pan?
To install, remove food from the area, slide out and remove any obstructing shelves, then align the rear of the pan with the rear support rails. Angle the front slightly upward (if needed) and slide the pan straight back until it seats on both rails and the front lip rests on the front support. If the drawer has stops or tabs, ensure they engage. No tools are normally required.
What are common signs the crisper pan needs to be replaced?
Replace the pan if you see cracks, chips, warping, or broken mounting tabs that prevent proper seating or sliding. Other signs include persistent water pooling that won’t drain,a drawer that won’t stay level or pull smoothly,or visible food contamination that cannot be cleaned.Damaged pans can allow leaks that drip onto lower shelves or the freezer compartment.
Is 240351240 an OEM part or an aftermarket replacement?
The part number 240351240 is presented as an OEM Frigidaire part number. When ordering, verify the seller lists it as an OEM Frigidaire (or Electrolux/Frigidaire Group, depending on supplier) part to ensure material and fitment match the original. Aftermarket options may exist, but they can differ slightly in dimensions and fit.
How should I clean and maintain the crisper pan?
Clean the pan with warm water and mild dish soap using a soft sponge. Rinse and dry thoroughly before reinstalling. Avoid abrasive pads or strong chemicals (bleach, oven cleaners) that can damage plastic or printed markings. If the part listing indicates it is dishwasher-safe, you may use the dishwasher, but hand washing is safest for longevity.
Can a damaged crisper pan cause temperature or humidity problems in the crisper drawer?
A cracked or ill-fitting pan can let cold air bypass the drawer area and allow excess moisture to collect or escape, which can affect humidity control and the freshness of produce. while the pan itself doesn’t control temperature, proper sealing and rail alignment help the drawer maintain the intended microclimate. If you suspect humidity issues, also check the cover/damper and the drawer rails for damage.
Where is the best place to buy part 240351240 and does it come with a warranty?
Buy from Frigidaire’s official parts store, authorized appliance parts dealers, or well-known online parts retailers. When ordering, confirm the seller’s return policy and warranty-OEM parts often carry a limited warranty through the manufacturer or dealer, but terms vary. Keep your refrigerator model number and part number handy to ensure you receive the correct item.
To Wrap It Up
The 240351240 Frigidaire refrigerator crisper pan serves a fundamental role in preserving produce and maintaining interior cleanliness. Designed to collect moisture and debris beneath the vegetable drawers, the pan helps regulate humidity levels, prevent leaks from entering the refrigerator cavity, and reduce the risk of staining or odor development. Its proper function contributes directly to food quality and to the overall performance and longevity of the appliance.
Accurate diagnosis is essential when issues such as persistent odors, visible cracks, warping, or water pooling are observed. Confirming that the pan is the source of a problem-rather than a failing drawer seal, clogged drain, or other component-avoids unnecessary parts replacement and ensures the correct corrective action. When replacement is required, using the correct part number and following manufacturer guidelines or qualified service advice helps restore proper fit and function.
Maintaining or replacing a worn 240351240 crisper pan is a straightforward,cost-effective step in refrigerator upkeep that supports food safety and reduces the likelihood of secondary damage.By prioritizing correct diagnosis and timely replacement with appropriate parts, owners can keep their Frigidaire units operating efficiently and extend the useful life of the appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
