241796405 Frigidaire Refrigerator water Tube Fill is a molded water delivery tube assembly used on Frigidaire refrigerators to route water from the inlet valve to downstream components such as the ice maker fill cup or internal dispenser lines. As a mechanical plumbing component, the tube provides a sealed, shaped pathway that aligns with appliance mounting points and sealing surfaces to enable repeatable, controlled water delivery inside the cabinet.
Inside the appliance the water tube fill interfaces directly with the water inlet valve, the ice maker fill port, dispenser plumbing and associated gaskets or O‑rings; it therefore plays a role in fluid routing, sealing and freeze/thermal isolation.Proper seating and orientation of the tube are required to prevent leaks, ensure correct fill volume to the ice mold and avoid kinking or restriction that would reduce flow. The part is typically located between the rear inlet valve area and the ice maker or dispenser assembly-often passing through the freezer compartment wall or door-and is crucial for reliable ice production and clean water dispensing and also for preventing water intrusion into insulation and electrical components.
This article will describe the tube’s intended function and materials, the Frigidaire models and assemblies with which 241796405 is compatible, common failure symptoms (for example no-fill, under-fill, overflow, or external leaking), diagnostic checks and troubleshooting procedures to isolate the tube versus valve or supply issues, and practical replacement considerations such as seal type, routing, mounting, pressure testing and safety precautions to follow during removal and installation.
Table of Contents
- Function and Role of the Fill Tube Assembly in refrigerator Water Delivery and Dispensing Systems
- How the 241796405 frigidaire Refrigerator Water Tube Fill Operates Within the Appliance Water Supply Pathway
- Common Failure Symptoms and Diagnostic Indicators for the Fill Tube Assembly
- Compatibility, Replacement Considerations, and Step‑by‑Step Installation Procedures for the Fill Tube
- Q&A
- To Wrap It Up
Function and Role of the Fill Tube Assembly in Refrigerator Water Delivery and Dispensing Systems
The 241796405 Frigidaire Refrigerator Water Tube Fill serves as the molded conduit that routes potable water from the refrigerator’s inlet valve to the ice maker fill cup and the internal water-dispensing circuit. In operation the fill tube provides a defined flow path and physical positioning so the solenoid valve can deliver a measured volume into the ice maker tray or dispenser line without splashing or siphoning back into the valve. Its geometry and mounting features also position the tube in relation to the evaporator and drain channels to reduce the risk of freezing or leakage; if the tube is cracked, misrouted, or obstructed, fill rate and fill timing will be affected and the ice maker or dispenser may overfill, underfill, or run continuously.
Compatibility and practical service considerations include checking connector type, tube diameter, and mounting tabs against the refrigerator model before replacing the part. Technicians commonly verify inlet water pressure,integrity of the solenoid valve,and the condition of any integrated check valve while diagnosing a slow-fill or leak condition; replacing the tube assembly (for example with part 241796405) is a straightforward repair when the tube itself shows physical damage or permanent deformation. Common symptoms and basic checks include:
- Slow or no fill: inspect for kinks, blockages, or frozen sections and measure inlet pressure at the valve.
- Continuous water flow or overflow: test the solenoid valve and look for a failed check/backflow feature at the tube connection.
- Visible leaks or ice buildup: examine mounting points and joints for cracks or improper seating.
| Item | Description |
|---|---|
| Function | Directs water from the inlet valve to ice maker or dispenser and positions fill outlet relative to ice tray/evaporator. |
| Typical connections | Press-fit or barbed 1/4″ to 5/16″ water tube fittings and model-specific mounting tabs; verify fitment against model list. |
| Common failure modes | Cracks,freeze fractures,blockages,and degraded seals at joints causing slow flow,leaks,or improper fill timing. |
How the 241796405 Frigidaire Refrigerator Water Tube Fill Operates Within the Appliance Water Supply Pathway
241796405 Frigidaire Refrigerator Water Tube Fill is the molded water conduit that carries metered water from the refrigerator’s inlet valve to the ice maker fill cup and, where applicable, to the internal water dispenser.It behaves as a low-volume, low-pressure transfer line: the inlet solenoid opens for a timed interval and the tube’s internal diameter and smooth bore determine the delivered volume and flow characteristics. The tube is typically made from abrasion- and scale-resistant polymer and is sized to match the OEM fill timing; installing a tube with a different inner diameter or connection style will change fill rates and can cause over- or under-fill conditions in the ice mold or cup.
- Flow role: downstream of the inlet valve, upstream of the fill cup or dispenser.
- Material and dimensions: polymer tubing with ~1/4″ ID or OEM-specific sizes.
- Connection types: push-fit, crimp, or barbed fittings matching factory ports.
- Common symptoms of failure: reduced fill volume, intermittent leaks, kinking, or slow fills caused by partial blockage or mineral buildup.
| Item | Description |
|---|---|
| Inner diameter | Typically ~1/4″ (6.35 mm) – governs flow volume and timing |
| Material | Polyethylene/nylon blend resistant to scale and freezer conditions |
| Connection | OEM-matched push-fit or crimped fittings; must match valve and fill cup ports |
Within the appliance water supply pathway the tube is routed and secured to avoid vibration, sharp bends, or pinch points that would alter flow or cause fatigue failures.Technicians should verify that tubing is free of kinks,properly seated at the valve and fill cup,and unobstructed by debris or scale; a practical diagnostic is to time a single fill cycle and compare delivered volume to factory specifications. When replacing this component,match the 241796405 Frigidaire Refrigerator Water Tube Fill by part number or ensure the replacement matches the original inner diameter,material,and connector style to preserve designed fill timing and system compatibility.
common Failure Symptoms and Diagnostic Indicators for the Fill Tube Assembly
The 241796405 Frigidaire Refrigerator Water Tube Fill is the molded delivery tube that channels pressurized water from the inlet valve to the ice maker fill cup or water dispenser. Its function is purely mechanical-maintaining an unobstructed, correctly positioned path and a sealed connection at both the valve and the ice maker fill nozzle-so failures are typically physical (cracks, kinks, loose fittings) or hydraulic (partial occlusion or freezing) rather than electrical.Compatibility matters: replacement tubing must match the OEM connector geometry and inner diameter to ensure proper flow rate and a reliable seal; an incorrect tube can cause slow fill, leaks at the joint, or improper fill volumes even though the valve and ice maker electronics are functioning normally.
Common diagnostic indicators are observable during a manual fill cycle and through simple inspections.Visible water pooling, frost or ice buildup along the tube, audible constant valve operation without corresponding water flow, or a markedly reduced fill time all point to tube-related issues. Technicians should verify inlet water pressure, inspect the tube path for bends or pinch points, run a manual harvest/fill to watch for direct flow into the ice maker fill cup, and confirm secure seating at both connector joints; a cracked or deformed tube typically requires replacement rather than repair.
- No water to the ice tray while the valve actuates – indicates blockage, kink, or disconnected tube.
- Slow or partial fills – suggests partial occlusion, reduced inlet pressure, or undersized/incorrect tube inner diameter.
- Overflowing or overfilled ice mold – can result from mispositioned tube or worn/nozzle sealing surfaces.
- Water pooling inside the refrigerator cabinet – sign of leaks at tube joints or a cracked section of tubing.
- Frost/ice formation on the tube – indicates internal freezing or a cooling air leak contacting the line.
| item | Description |
|---|---|
| No flow while valve clicks | Tube kinked, disconnected, or internally blocked; verify continuity of tubing and connection integrity. |
| Reduced fill volume | Partial obstruction, frozen segment, or insufficient inlet pressure; inspect tube interior and measure line pressure. |
| External leak | Cracked tubing or improperly seated connector; replace tube and ensure correct OEM-style fittings are used. |
Compatibility, Replacement Considerations, and Step‑by‑Step Installation Procedures for the Fill Tube
The fill tube is the rigid conduit that carries water from the refrigerator inlet valve to the dispenser tray or ice maker; the replacement part 241796405 Frigidaire Refrigerator Water Tube Fill is an OEM-style component engineered to match factory dimensions, barb fittings, and mounting points so flow characteristics and sealing surfaces remain consistent with the original assembly. This tube is typically molded from nylon or high-density polyethylene to resist scale and low-temperature embrittlement; technicians should verify the refrigerator model number, tubing diameter (commonly 1/4″ OD for service lines at the inlet) and the connection type (barbed, push-fit, or speedy-disconnect) before ordering to ensure compatibility and to avoid adapting fittings that could introduce leaks or flow restrictions.
Replacement and installation are straightforward when you follow controlled steps: isolate the water supply and electrical power, relieve residual pressure in the line, remove any retaining clips or insulation, swap the old tube for the new one while preserving routing to prevent kinks, and then test under normal operating pressure for leaks and proper fill timing.Consider replacing clamps and any degraded o-rings during service; if the refrigerator uses soldered or crimped metal tubing transitions, plan for an adapter or professional crimping tools rather than forcing incompatible fittings, and verify that the ice maker fills to the expected volume during a diagnostic cycle to confirm correct installation and valve operation.
- Shut off the water supply and unplug the refrigerator or switch off the breaker.
- locate and remove access panels or panels in the fresh-food compartment to reach the fill tube routing and mounting clips.
- Loosen or remove clamps/quick-disconnects, slide out the old tube, inspect fittings and o-rings, and clean mating surfaces.
- Install the new tube, ensure full engagement on barbed fittings, replace clamps or use new push-fit seals, and restore original routing to prevent stress or kinks.
- Restore water and power, check for leaks at all joints under normal pressure, and run the dispenser/ice maker to purge air and confirm proper fill volume.
| Item | Description |
|---|---|
| Material | Nylon or HDPE for low-temperature resilience and scale resistance |
| Typical connection | 1/4″ OD barbed or push-fit; verify against service manual |
| common failures | Cracks from impact/freezing, brittle fractures, or seal deterioration at fittings |
Q&A
What is Frigidaire part 241796405 and what does it do?
Part 241796405 is the water fill tube assembly used on some Frigidaire refrigerators. It directs the incoming household water from the inlet/solenoid toward the ice maker mold (and in some designs toward the dispenser). Its job is to control where water is delivered so the ice maker fills correctly and to prevent leaks inside the cabinet.
How can I tell if the water fill tube is failing or clogged?
Common symptoms of a failing or clogged fill tube include the ice maker not filling or filling slowly, partial or no ice production, visible water leaks under or inside the freezer, frost buildup along the tube, or water pooling inside the freezer. Inspect the tube for visible cracks, splits, kinks, disconnections or ice/blockages. If the tube is frozen solid or has mineral deposits inside it, flow will be restricted.
Which refrigerator models use part 241796405?
This part is used on various Frigidaire and related-brand refrigerators. Model coverage can change, so do not rely on model memory alone-confirm compatibility by entering your refrigerator model number on Frigidaire’s parts website, checking the parts diagram in your owner’s manual, or contacting an authorized parts dealer.You can find the model number typically on a sticker inside the refrigerator compartment or on the cabinet frame.
Can I replace the water fill tube myself? What tools and steps are required?
yes, a competent DIYer can usually replace it. General steps: unplug the refrigerator and shut off the water supply; remove the freezer/ice maker access panels and, if required, the ice maker assembly to access the tube; remove retaining clips or screws and disconnect the old tube from the inlet/valve and the ice maker; install the new tube making sure connections are secure and routed to avoid kinks; reassemble panels, restore water and power, and test for leaks and proper fill. typical tools: flat and Phillips screwdrivers, pliers, possibly nut drivers and a towel/bucket. Take care with sharp sheet metal, and follow safety steps (power and water off).
How do I test whether the fill tube or the water valve/pressure is the problem?
First visually inspect and clear any ice or debris from the tube. Run an ice maker harvest/test cycle (or manually advance the ice maker) and observe whether water reaches the mold. If no water reaches the ice maker but the valve clicks,test the water inlet valve: remove the connector and check for 120 VAC (or the specified control voltage) when the ice maker calls for water and check valve continuity with a multimeter. If the valve is energizing but there is no flow, check water pressure and supply line for blockages. If the valve supplies water to a bucket when removed but the tube still doesn’t fill,the tube may be blocked or misrouted.
What causes a fill tube to freeze, and how do I prevent it?
The fill tube can freeze when exposed to very cold airflow from the evap coil, when it has a small leak introducing moisture, or when the tube sits against very cold surfaces. Restricted airflow in the freezer, a failing door gasket, or thermostat/defrost issues that let temperatures run too cold also increase risk. Prevent freezing by ensuring the tube is routed away from the coldest areas, replacing damaged gaskets, keeping the freezer at the correct temperature, and repairing any defrost or airflow problems. If the tube repeatedly freezes, consider replacing it or adding insulation where it passes through the cabinet.
Can I use an aftermarket or universal replacement fill tube for part 241796405?
Aftermarket replacements and universal tubes are available and can work if they match the original’s length, fittings, and material (food-grade plastic). OEM parts are recommended because they match fitment and materials exactly. If using an aftermarket part, verify connector size, mounting clip locations, and that the material is compatible with potable water. Keep receipts and verify the return policy in case it does not fit.
How much does replacing the water fill tube typically cost and where should I buy one?
Prices for the part alone are generally modest-frequently enough in the range of a few dollars up to around $30-40 depending on source and whether grommets/clips are included. Labor costs, if you hire a technician, will add more. Buy from Frigidaire’s official parts site, authorized appliance parts distributors, reputable online appliance parts retailers, or local appliance repair shops. Always verify the part number against your model number before purchasing.
To Wrap It Up
The 241796405 Frigidaire Refrigerator Water Tube Fill is a specific replacement component designed to deliver and direct water to the refrigerator’s ice maker and dispenser assembly. Its correct fit and function contribute to consistent water flow, reliable ice production, and the prevention of leaks or water damage within the cabinet. As a discrete part of the appliance’s water delivery system, its condition can directly affect performance, food safety, and long-term reliability.
As symptoms such as reduced flow,intermittent dispensing,visible leaks,or ice maker failures can stem from multiple causes,proper diagnosis is critically important before replacing the tube fill. Confirming the root cause-through inspection of connections, valves, water pressure, and surrounding components-helps ensure the correct repair is made. When replacement is required, using the appropriate part and following manufacturer guidance or qualified service procedures minimizes the risk of improper installation and further issues. Timely, accurate diagnosis and replacement preserve appliance performance and reduce the likelihood of more extensive repairs down the line.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
