241860810 Frigidaire Refrigerator Ice Container Assembly is a molded ice storage adn delivery module designed for use in refrigerators equipped with automatic ice makers and dispensers. As a mechanical receptacle, it typically includes the ice bin, mounting interfaces, and any internal delivery components such as an auger or guide surfaces; it is indeed manufactured to fit into the freezer compartment and to accept ice produced by the ice maker while aligning with the dispenser opening or chute.
Inside the appliance, the ice container assembly serves as the interface between the ice-making subsystem and the user-facing dispensing system. It receives discharged ice cups or cubes from the ice maker, stores them in a controlled cavity to minimize clumping and bridging, and, where applicable, presents or feeds ice to an auger or gate mechanism that meters ice to the dispenser. The assembly interacts mechanically with the ice maker (timing and discharge), electrically with sensors or switches that detect bin presence or level, and physically with the dispenser door, gasket/seal surfaces and surrounding freezer structure; proper alignment and sealing are important to avoid jams, backflow, or frost buildup that can impede operation.
This article will describe the component’s function and basic construction, outline common compatibility considerations and installation interfaces, identify typical failure symptoms (for example ice bridging, dispenser jams, noisy or non-rotating auger, incorrect level sensing, or water intrusion), and provide practical troubleshooting and replacement guidance. readers can expect guidance on inspection steps,diagnostic checks for motors and sensors,mechanical and electrical points to verify,and the key dimensional and connector details to confirm correct replacement parts and safe installation practices.
Table of Contents
- Functional Role of the Ice Container in Refrigerator Ice Production and Storage
- How the 241860810 Frigidaire Refrigerator Ice Container Assembly Operates and Interfaces with the Ice Maker, Auger, and Dispenser
- Common Failure Symptoms and measurable Indicators for the Ice Container Assembly
- Model Compatibility, Replacement Considerations, Installation Procedure, and Diagnostic Troubleshooting
- Q&A
- The Way Forward
Functional Role of the Ice Container in Refrigerator Ice Production and storage
The 241860810 Frigidaire Refrigerator Ice Container Assembly functions as the mechanical and thermal interface between the ice maker and the user-accessible storage area. It receives cubes from the ice-maker discharge chute, provides a controlled volume for storage, and positions any fill-level sensor or microswitch so that the refrigerator’s control board can enable or halt production. constructed from food-grade, low-conductivity polymer and designed with specific mounting tabs and stops, the assembly reduces cube fragmentation on impact, channels meltwater to the freezer drain, and helps maintain an internal microclimate that limits refreezing and bridging under normal operating conditions.
Performance and compatibility depend on correct seating, undamaged mounting features, and a clean interior surface; a slightly warped bin or worn latch will change alignment and can cause jamming, false full signals, or intermittent ice production.For troubleshooting or replacement, verify that the bin’s tabs match the freezer cavity, check continuity of any integrated sensor circuit, and inspect for cracks or deformations that alter cube flow paths. Practical examples include a misaligned bin that trips the fill-level switch and stops the ice maker cycle, or a container with poor drainage that produces partially melted, refrozen chunks; routine cleaning and visual inspection prevent most of these issues.
- Key features: molded fill geometry,integrated sensor/microswitch interface,mounting tabs,and drain channeling.
- Common failure symptoms: ice bridging/jamming, false “full” sensor activation, water pooling, and increased cube fragmentation.
- Service checks: verify bin seating, inspect tabs and sealing edges, and test sensor continuity if production has stopped.
| Item | Description |
|---|---|
| material | Food-grade low-conductivity polymer; minimizes thermal transfer and resists cracking |
| Mounting | Model-specific tabs and stops that align with freezer cavity and ice-maker discharge chute |
| Interface | Optional fill-level sensor/microswitch contact for control board signaling |
How the 241860810 Frigidaire Refrigerator Ice container Assembly Operates and Interfaces with the Ice Maker, Auger, and Dispenser
The 241860810 Frigidaire Refrigerator Ice Container Assembly serves as the removable ice storage and interface module between the ice maker, the auger drive, and the dispenser mechanism. Mechanically, the bin provides a splined or keyed hub that engages the auger shaft so rotational torque from the auger motor is transferred to move ice toward the dispenser; this engagement must be aligned and free of obstructions for consistent dispensing. Electrically and functionally,the container frequently enough includes a presence/detection feature – either a spring-actuated switch,magnetic flag,or optical sensor – that signals the control board when the bin is seated and ready,preventing the auger from running when the bin is absent or misaligned. In practical service work, technicians verify physical coupling, check for worn splines or stripped plastic, and confirm continuity or correct switching behavior on the presence sensor when diagnosing no-dispense or intermittent-dispense faults.
The container also defines the ice flow geometry and clearance around the auger flighting; large ice pieces, compacted ice bridges, or accumulated frost at the bin ledge commonly cause auger stalls or motor overloads and can mimic electrical faults. Compatibility is primarily mechanical: replacement bins must match the freezer cavity mounting points, auger hub profile, and presence-sensor location for correct operation; swapping a bin with different hub geometry or sensor position will prevent engagement or proper detection. For practical troubleshooting, check that the auger rotates freely when the bin is removed, inspect the bin’s inlet for foreign objects, and observe the dispenser actuator or door movement to ensure the mechanical path from auger to dispenser chute is unobstructed.
- Key interface points: splined/ keyed auger hub engagement, presence/detection sensor, dispenser chute alignment, and retention tabs.
- Common symptoms indicating interface issues: no ice dispensed,auger motor hum with no rotation,or door-switch-related lockouts.
- Service checks: verify bin seating, test sensor continuity, inspect splines for wear, and clear ice bridges or frost buildup.
| Item | Description |
|---|---|
| Drive interface | Splined/keyed hub that mates to auger shaft; must be undamaged and properly aligned. |
| Container sensor | Spring switch, magnetic flag, or optical sensor that reports bin presence to the control board. |
| Mounting/compatibility | Matches freezer cavity mounting points and dispenser geometry; mismatched bins will fail to engage. |
Common Failure Symptoms and Measurable Indicators for the Ice Container Assembly
The 241860810 Frigidaire Refrigerator Ice Container assembly is a molded storage and interface component that receives ice from the automatic ice maker, provides a controlled outlet for dispensing, and houses any bin-level sensors or chutes specific to compatible Frigidaire models. Functionally it must align with the ice-maker discharge port and any dispenser actuator or auger, seal against the freezer cavity to prevent frost build-up, and permit free movement of ice without binding. Compatibility is persistent by mounting boss locations, sensor type (mechanical arm versus optical/switch), and chute geometry; using a non‑matching bin will commonly produce misalignment, increased friction at the discharge point, or incorrect sensor actuation, all of which degrade performance even when the ice maker itself is functional.
Common failure symptoms and measurable indicators include reduced ice yield, frequent clumping or bridging of ice, intermittent dispenser jams, and repeated ice-maker harvest cycles. Useful diagnostics are: measure freezer compartment temperature (target ~-18°C/0°F; persistent readings above -10°C frequently enough correlate with wet, sticky ice), inspect bin geometry and clearances for warping or cracking, verify sensor continuity or voltage at the bin sensor connector during normal and tripped states, and monitor dispenser/auger motor current for spikes that indicate mechanical resistance. Practical examples: a cracked discharge lip that reduces the 10-15 mm clearance can cause repeated jams, and a sensor that shows no open/closed change under actuation typically points to failed switch or damaged wiring rather than the ice maker itself.
- No ice dispensed or small quantities despite normal water fill.
- Ice clumping or large ice slabs that jam the chute.
- Ice maker cycles frequently without increasing stored ice.
- Audible grinding or increased motor current during dispense.
- visible cracks, deformation, or improper seating of the bin.
| Item | Description |
|---|---|
| Freezer temperature | Nominal ~ -18°C (0°F); sustained > -10°C correlates with wet/clumpy ice. |
| Bin sensor | Measure continuity or voltage change between empty and full positions; no change indicates sensor or wiring fault. |
| Dispenser/auger load | Current draw spikes or stall torque during dispense indicate mechanical obstruction or warped bin geometry. |
Model Compatibility, replacement Considerations, Installation Procedure, and Diagnostic Troubleshooting
The 241860810 Frigidaire Refrigerator Ice Container Assembly is the molded housing and dispensing interface that stores ice from the ice maker, guides cubes toward the dispenser chute, and frequently enough integrates the ice level sensor and drive motor coupling. Compatibility depends on physical mounting features (tab spacing, screw locations), electrical connector type, and whether the dispenser actuator and door geometry match the refrigerator façade; two assemblies with identical electrical harnesses can still differ by chute angle or actuator cam profile. When considering replacement, compare part numbers, measure critical dimensions (mounting tab center‑to‑center, chute opening width), and inspect the mating surfaces on the evaporator/ice maker so that sensor alignment and motor engagement occur without stress or binding during operation.
Installers should follow a controlled sequence to avoid damage: disconnect power, remove the freezer shelf or trim to access the assembly, detach the harness and any dispenser linkage, remove only the fasteners required to free the housing, then seat the replacement so the motor spline and sensor face locate without interference, reconnect harnesses, and restore power to verify motor rotation and sensor state. Diagnostic troubleshooting targets mechanical obstruction, electrical continuity, and sensor feedback – common faults present as noisy motor operation, intermittent dispensing, ice jams, or an always‑full/always‑empty level sensor reading; check for frozen bridges of ice at the chute, measure motor winding resistance, and confirm the sensor sees the correct voltage and ground reference before replacing the assembly.
- Common symptoms: jammed dispensing, motor hum without rotation, ice overflow or constant shutoff from level sensor.
- Rapid checks: verify unobstructed chute, continuity across motor terminals, correct harness seating, and free rotation of the agitator when hand‑turned.
- Replacement tip: document connector pinout and mounting screw locations before removal to avoid misrouting wires or misaligning sensors.
| Item | Description |
|---|---|
| Mounting tab spacing | Measure center‑to‑center to confirm fit with freezer liner (typical tolerance ±2 mm). |
| connector type | 3-5 pin sealed plug; verify keyed orientation and pin assignments against wiring diagram. |
| Materials | ABS housing with polypropylene chute; check for cracks or UV embrittlement in older units. |
Q&A
What is the 241860810 Frigidaire Refrigerator Ice Container Assembly and what does it do?
The 241860810 Frigidaire Ice Container Assembly is the replacement ice bucket/bin that collects and stores ice produced by the refrigerator’s ice maker. It typically sits below the ice maker, guides ice into the dispenser (if applicable), and frequently enough has molded rails or stops so it slides in and out cleanly.
How do I know if the 241860810 part is compatible with my refrigerator?
compatibility is determined by your refrigerator’s model number. Locate the model tag (usually inside the fresh food compartment, on the side wall, or behind a grille), then check Frigidaire’s official parts lookup or a reputable parts dealer and search for 241860810. Don’t rely only on visual similarity-verify the part number against your exact model to ensure fit and function.
how do I remove and install the 241860810 ice container assembly?
To remove: empty the ice, open the freezer door, slide the bin forward until it stops, then either lift slightly and pull out or disengage any retaining tabs depending on your model. To install: align the bin’s rails with the refrigerator guides, slide it back until it seats flush and any tabs click into place. Always unplug or disconnect power before working inside the freezer if you need to clear ice around the ice maker, and handle the bin gently to avoid cracking plastic.
What should I do if the ice container is cracking or leaking and I need a replacement?
If the container is cracked,warped,or leaking,replace it with the correct OEM part (241860810). Order from Frigidaire or an authorized parts dealer to ensure you get an exact replacement.Inspect mounting points and surrounding components for damage-if a broken mount caused the crack,replace or repair the mounting hardware as well.
How do I clean and sanitize the 241860810 ice container assembly?
Empty the ice and hand-wash the bin with warm water and mild dish soap. Rinse thoroughly and dry completely before reinstalling. For sanitizing, you can use a diluted bleach solution (about 1 tablespoon household bleach per gallon of water) or a 50/50 solution of water and white vinegar; rinse thoroughly afterward. Avoid abrasive scrubbers and very hot water or dishwashers unless the manufacturer specifically states the part is dishwasher-safe.
My ice keeps clumping or jamming in the bin-could the ice container be the problem?
Clumping and jamming are often caused by humidity, an overly cold freezer causing partial refreezing, or an improperly seated bin that blocks the ice flow. Check freezer temperature (ideally 0°F/-18°C), make sure the bin is fully seated and not misaligned, and break up any ice bridges with a plastic scoop or paddle (never use metal tools). if the bin has deformed or the dispenser chute is damaged, replacing the bin (241860810) might potentially be required.
Do I need tools to replace the ice container assembly and how long will it take?
Most replacements require no tools-just your hands to slide the bin out and back in. If your model uses a retaining screw or bracket, a screwdriver might potentially be needed. Typical replacement time is under 10 minutes for standard models: empty the ice, remove the old bin, install the new bin, and test fit.
Where can I buy the 241860810 Frigidaire ice container assembly and is there a warranty?
You can purchase 241860810 from Frigidaire/Electrolux parts websites, authorized appliance dealers, or reputable online parts retailers.Verify the seller’s return policy and warranty-OEM parts often come with limited warranties through the manufacturer or seller. Keep your receipt and the refrigerator’s model/serial number for warranty claims or returns.
The Way Forward
the 241860810 Frigidaire Refrigerator Ice Container Assembly serves a fundamental role in ice storage and delivery within compatible Frigidaire refrigeration units. Properly functioning, it protects ice from freezer odors and contamination, supports reliable dispensing or access, and helps maintain consistent ice production and appliance efficiency. As an OEM component, its correct fit and materials contribute to the refrigerator’s designed performance and food-safety standards.
Timely and accurate diagnosis of issues-such as cracks, misalignment, or buildup that impedes dispensing-helps distinguish between simple maintenance and the need for replacement. When replacement is necessary, selecting the correct 241860810 assembly and following manufacturer installation guidelines ensures safe operation, preserves ice quality, and reduces the risk of secondary damage to the appliance. Where uncertainty exists, professional inspection and installation reduce the likelihood of improper repairs and warranty complications.
Maintaining the ice container assembly as part of routine care supports long-term refrigerator reliability and user convenience. Prioritizing proper diagnosis, using compatible genuine parts, and employing qualified service when needed are practical steps to protect performance and safety while minimizing downtime and unexpected costs.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
