137006900 frigidaire Washer Strike is the specific replacement striker used in certain Frigidaire washing machines; it is a mechanical door strike-a small but critical hardware piece that engages the door latch assembly to secure the washer door or lid during operation. as a striker, the part provides the mating surface for the latch mechanism and is typically mounted to the washer cabinet or door frame; it may be produced in metal or reinforced polymer depending on the model and is identified by the 137006900 part number for ordering and compatibility checks.
Inside the appliance, the striker works as part of the door closure and safety interlock subsystem. When the door is closed, the latch captures the striker, mechanically holding the door and actuating any associated microswitches or sensors that inform the control board that the door is secure. This interaction affects several operational systems-control logic (cycle start and progression), motor engagement (spin and agitation authorization), and water-management sequences (fill and drain)-and it also contributes to maintaining a watertight closure during wash cycles. Improper alignment, wear, or damage to the striker can prevent the latch from sensing a closed door, which in turn will inhibit normal operation or compromise safety.
In this article you will find a technical overview of the 137006900 striker’s function, typical application points and model compatibility considerations, common failure symptoms to recognize (for example, door not latching, machine not starting, intermittent door-sense faults, or leaks), and practical troubleshooting steps a technician or owner can use to isolate striker-related issues. The piece will also cover replacement considerations such as verifying fitment and orientation, inspecting related latch hardware and switches, recommended fastener practices, and testing procedures after installation to confirm correct mechanical engagement and electrical interlock behavior.
Table of Contents
- Functional Role and Mechanical Requirements of the Washer Door Strike Assembly
- How the 137006900 Frigidaire Washer Strike Operates within the door Lock Interlock and Control Circuit
- Common Failure Modes, Observable symptoms, and Diagnostic Tests for the Strike
- Compatibility, Replacement Specifications, Installation Procedures, and Troubleshooting for the Strike
- Q&A
- To Conclude
Functional Role and Mechanical Requirements of the Washer door Strike Assembly
The 137006900 Frigidaire Washer Strike functions as the mechanical mating point for the washer door latch and the cabinet interlock assembly. It provides a positive engagement surface that both holds the door closed under dynamic loads (spin and sudden imbalance) and positions the door actuator so the safety switch or lock mechanism can register a closed state. In practice this part must precisely align with the door striker plate and the cabinet mounting points; incorrect orientation, worn engagement surfaces, or incompatible mounting hole patterns will prevent reliable actuation and may allow the door to open during operation or prevent the machine from starting.
Mechanically, the strike assembly must meet modest tolerance and wear-resistance requirements: low-friction contact surfaces or hardened inserts where repeated engagement occurs, stable mounting to prevent movement under vibratory loads, and sufficient retention geometry to resist axial and radial forces generated during high-speed spin cycles. Common field symptoms of a failing strike include intermittent door-closed detection, audible rattling at spin speeds, or a door that appears to catch but does not fully latch. Practical checks include verifying alignment to the door latch, inspecting for burrs or deformation on the engagement face, and confirming that any actuator tip consistently depresses the cabinet switch. Typical characteristics and checks are summarized below:
- engagement geometry: ensures repeatable actuation of the door switch and positive retention.
- Mounting stability: fixed to cabinet with correct fasteners and torque to avoid loosening.
- Wear surfaces: free of nicks, excessive wear, or corrosion that alter engagement depth.
| Item | Description |
|---|---|
| Function | provides mechanical interlock and positions the door actuator for electrical/safety switch engagement. |
| Critical requirements | Alignment to latch, wear-resistant engagement face, stable mounting against vibratory loads. |
| Common failure symptoms | Intermittent door-closed signals, rattling, inability to start, or door opening during cycles. |
How the 137006900 Frigidaire Washer Strike operates Within the Door Lock Interlock and Control Circuit
The 137006900 Frigidaire Washer Strike is the mechanical actuator that engages the door lock interlock and provides the control board with a definitive closed/open state. Mounted on the cabinet frame, the striker physically engages the latch or plunger of the interlock assembly so that as the door closes the striker either depresses a microswitch or properly positions a sensor, completing the circuit that signals a door locked condition and allowing the washer’s drive and control logic to proceed. Proper fitment and geometry matter: the striker must align with the existing latch and switch travel to transfer a reliable mechanical action into a clean electrical signal to the control module.
The strike itself is a passive mechanical component whose failures are primarily mechanical-wear, broken mounting tabs, or misalignment prevent full actuation of the interlock switch and produce control-side symptoms. troubleshooting focuses on verifying mechanical engagement and the integrity of the interlock circuit: inspect striker surface and mounting, manually actuate the interlock while observing continuity or switch state with a multimeter, and confirm the control board receives the expected contact closure or sensor change. Replacing a damaged or incorrectly aligned striker with the OEM-specified unit restores the required geometry for consistent switch operation and eliminates many intermittent lock or no-start faults.
- Primary role: convert door position into a repeatable mechanical actuation for the interlock switch.
- Common symptoms of failure: washer will not start, intermittent lock indication, or door-lock error codes.
- Basic diagnostics: visual inspection, manual actuation while measuring continuity, and verifying harness/connectors.
- Compatibility note: must match mounting points and striker geometry to engage the existing interlock reliably.
| item | Description |
|---|---|
| Function | Mechanical engagement of door to actuate interlock switch and provide a clear locked/unlocked signal. |
| Interface | Physical striker to microswitch or sensor; control board expects a contact closure or sensor change. |
| Common failures | Wear, broken tabs, misalignment, or plastic deformation preventing full switch actuation. |
| Diagnostic tip | Measure continuity while manually actuating the striker and verify consistent switch travel and alignment. |
Common Failure Modes, observable Symptoms, and Diagnostic Tests for the Strike
The 137006900 Frigidaire Washer Strike is the mechanical engagement point on the cabinet that the door latch bears against to register a closed door and actuate the interlock or door switch.It provides a precise surface and alignment datum so the latch can depress the microswitch or allow the lock assembly to fully engage; wear, plastic creep, or improper replacement can change the strike’s geometry and prevent reliable contact. Compatibility matters: the strike’s mounting boss locations,thickness,and molded profile must match the washer model’s latch travel and switch position,otherwise the door may appear closed without completing the electrical circuit that allows the machine to proceed through its cycle.
Common failure modes include plastic fracture at the mounting points, rounding of the striker face, contamination by detergent residue, and deformation that shifts the contact point. Diagnostic testing combines visual and functional checks: inspect for cracks or melted plastic, verify that the striker is secure and not rotated or pushed away from the latch path, manually operate the door latch while observing switch closure, and isolate the interlock with a multimeter to confirm continuity when the striker is engaged. Practical examples: a washer that refuses to start but shows a closed door is often caused by a worn striker that no longer depresses the door switch, while intermittent starts or mid-cycle door pops indicate a loose mounting or intermittent contact.
- Door will not start or displays a door-lock error despite closing
- Audible rattling or clunking near the strike during spin cycles
- Door pops open or does not fully latch under light pressure
- Visible cracks, deformation, or missing mounting bosses on the strike
| Item | Description |
|---|---|
| Visual inspection | Check for cracks, wear on the striker face, and secure mounting; replace if deformation or missing bosses are present. |
| Mechanical alignment test | Close the door slowly and confirm the latch contacts the striker cleanly; measure misalignment by observing lateral or vertical offset. |
| Electrical continuity | With a multimeter, verify the door switch or interlock closes when the latch contacts the strike; intermittent or no closure implicates strike alignment or switch failure. |
Compatibility, Replacement specifications, Installation Procedures, and Troubleshooting for the Strike
The 137006900 Frigidaire Washer Strike is the stationary catch that the washer door latch engages to secure the door during fill and spin cycles. Functionally it transfers mechanical load from the door latch to the cabinet and ensures the door switch or interlock is fully actuated; failure of the strike typically presents as an unlatched door condition, intermittent start failure, or audible rattling during spin. Compatibility depends on the strike’s mounting hole spacing, thickness, and engagement geometry rather than brand alone, so technicians shoudl compare physical dimensions and the latch engagement profile to the original part rather than relying solely on model lists. Common failure modes include plastic wear or deformation from repeated impact, screw-hole elongation, and misalignment caused by bent frames or loose mounting hardware.
Replacement and installation require basic mechanical inspection and alignment checks: isolate power, remove the access panel, unfasten the strike screws, and compare the new strike to the old one for identical mounting pattern and engagement depth. During reinstallation, secure the strike so the latch engages smoothly without binding; use the original fasteners where possible and avoid excessive torque that can crack plastic components. troubleshooting should include a visual inspection for wear, a manual actuation test of the latch while watching the interlock/switch, and verifying that the strike sits flush with the cabinet where the latch contacts it; if the door still fails to latch after installing a new strike, inspect the latch, interlock switch, and surrounding frame for deformation or foreign debris that could prevent full engagement.
- symptoms: door will not lock, washer will not start, intermittent start, door opens during spin, audible rattle.
- Swift checks: inspect strike for cracks/wear, confirm mounting hole alignment, manually actuate latch and observe switch engagement.
- Installation reminders: isolate power, use original fasteners, align strike for smooth engagement, avoid overtightening.
- Troubleshooting tip: if visual and mechanical checks pass, test the interlock switch electrically to separate mechanical from electrical failures.
| Item | Description |
|---|---|
| part | 137006900 Frigidaire Washer Strike |
| Function | Stationary catch that engages the door latch and actuates the door interlock |
| Common failure modes | Plastic wear, deformation, screw-hole elongation, misalignment |
| Installation notes | Match mounting pattern and engagement depth; use original fasteners; ensure flush seating and free motion of the latch |
Q&A
What is the 137006900 Frigidaire Washer Strike?
The 137006900 is the replacement door strike (also called a latch strike or catch) used on certain Frigidaire washing machines. It is the part that the washer door or lid engages with so the door stays closed and the door-latch or lock assembly can complete the safety circuit. Depending on the washer design the strike may be a simple mechanical catch or part of an assembly that works with an electrical door-lock switch.
How do I know if the strike (137006900) is the reason my washer won’t start?
Common signs of a faulty strike include the washer not recognizing the lid/door is closed, the cycle not starting, intermittent door-closed errors, or the door not latching securely. inspect the strike for visible damage, cracks or worn plastic and verify the door lines up with and fully engages the strike. If the strike is broken or the door can close without engaging the latch, it likely needs replacement. Also check related components (door latch/lock assembly and wiring) before replacing the strike alone.
Can I test the 137006900 strike with a multimeter?
most simple strikes are mechanical and cannot be tested electrically, but if the strike incorporates a switch or works together with a door-lock microswitch, you can test continuity of the associated switch. Unplug the washer, disconnect the harness to the switch, and use the multimeter on continuity or ohms while operating the door/strike to see if the switch closes. If the switch does not change state when the door is properly engaged, the strike or switch assembly is defective. If unsure,visually inspect the mechanical engagement first.
How do I replace the 137006900 strike – is it a do-it-yourself job?
Replacement is often a straightforward DIY job if you are pleasant with basic hand tools. General steps: unplug the washer, open the access that exposes the strike (top-panel or front bezel depending on model), remove screws securing the old strike, remove and install the new strike in the same orientation, reassemble panels and test the door closure and a quick cycle. Typical tools: screwdriver set, nut driver, and possibly a trim tool. If your model requires removing control consoles or special fasteners, consult the service manual for that model. If electrical components are involved or you are unsure, hire a technician.
Do I need to calibrate or programme the washer after installing the new strike?
Most Frigidaire washers do not require calibration or programming after replacing a mechanical strike – they will detect the closed door normally at the next cycle. on rare models with electronic door-lock sensors, you might need to run a diagnostic or reset the control (unplug for 1-5 minutes) if the control does not recognize the new part. Consult the washer’s service manual for model-specific reset or diagnostic procedures.
How much does a 137006900 Frigidaire Washer Strike cost and where can I buy it?
Prices vary by supplier and whether the part is OEM or aftermarket. Expect a replacement strike to be in the low tens to low hundreds of dollars range depending on whether it’s a simple plastic strike or a more complete latch/lock assembly. Buy from authorized Frigidaire parts dealers, major appliance parts retailers, or trusted online marketplaces. Always verify compatibility by entering your washer model number before purchasing.
What else should I check if replacing the strike doesn’t fix the problem?
If replacing the strike doesn’t solve the issue, check the door latch/lock assembly, door alignment/hinges, and wiring harnesses for damage or loose connectors. Inspect the door switch or lock actuator (if present) and the control board for error codes or stuck relays. Running the washer’s service diagnostic mode (per the service manual) can definitely help identify whether the control is detecting the door latch closure signal. If electrical faults are present, consider calling a qualified technician.
Are there different versions or compatible part numbers I should be aware of when ordering 137006900?
Manufacturers sometimes supersede part numbers or provide compatible alternatives. Always cross-reference 137006900 with your washer’s model number and the parts supplier’s compatibility list. If a direct OEM 137006900 is unavailable, a supplier may list equivalent or superseded part numbers - confirm that the physical fit and function match your original strike before installing.When in doubt, order through an authorized Frigidaire parts dealer with your appliance model number on hand.
To Conclude
The 137006900 Frigidaire washer strike is a small but essential component that aligns and secures the door or lid so the machine can engage its locking mechanism and complete wash cycles safely and effectively. When functioning correctly, this strike contributes to proper door closure, prevents accidental interruptions during operation, and helps maintain overall washer performance and user safety.
Accurate diagnosis is significant before replacing the strike to ensure it is the root cause of the problem. Symptoms such as a door that will not latch, error codes related to door lock, or visible wear or damage to the strike should be confirmed through inspection and testing. Verifying the specific part number and compatibility with the washer model helps avoid needless replacements and ensures the repair addresses the actual fault.
When inspection indicates the 137006900 strike is worn, damaged, or incompatible, replacement with the correct part restores reliable door engagement and contributes to safe, normal operation. For best results,follow manufacturer guidance or consult a qualified technician for installation,ensuring compatibility,proper alignment,and adherence to any safety procedures. Proper diagnosis and timely replacement help prolong the life of the appliance and reduce the risk of recurring service issues.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
