241734001 Frigidaire refrigerator Ice Bucket is a factory-designated replacement ice storage container used in compatible Frigidaire refrigerator models. It is indeed a removable, food-grade storage component that receives adn holds ice produced by the refrigerator’s ice-making assembly; as an OEM part number it identifies the specific fitment and mounting geometry required for proper installation in the freezer compartment.
Inside the appliance, the ice bucket serves as the intermediary between the ice maker’s ejection mechanism and any internal or door-mounted dispensing systems. It interfaces mechanically with the ice maker ejector (or auger) and with any lid, sensor, or actuator that controls ice release, and it also affects how ice is presented to a dispenser chute. Proper seating and intact mounting tabs ensure correct alignment with the auger motor or dispenser drive, while the bucket’s shape and clearance influence ice flow, packing, and freeze/thaw behavior that can lead to jams or clumping.
In this article readers will find a technical overview of the ice bucket’s function, guidance on confirming compatibility by cross-referencing the 241734001 part number and model fit lists, common failure symptoms (cracks, broken tabs, misalignment, dispenser jams, and sanitary concerns), practical troubleshooting checks to isolate the bucket from ice-maker or dispenser faults, and considerations for replacement (matching OEM dimensions and mounting, handling and sanitation, and basic installation alignment points). The content is intended to help technicians, engineers, and appliance owners assess whether the bucket is the source of an issue and to inform correct selection and basic servicing decisions.
Table of contents
- Function and Role of the Ice Bucket Assembly in Frigidaire Refrigerator Ice Production
- How the 241734001 Frigidaire Refrigerator Ice Bucket Integrates with the Ice Maker, Motor, and Water Delivery System
- Common Failure Symptoms and Diagnostic Indicators for the Ice Bucket (cracking, jamming, misalignment, and moisture intrusion)
- Compatibility, Replacement Considerations, and Step‑by‑Step Installation for the 241734001 Ice Bucket
- Q&A
- Key Takeaways
Function and Role of the Ice Bucket Assembly in Frigidaire Refrigerator Ice Production
241734001 Frigidaire Refrigerator Ice Bucket serves as the primary ice collection and staging component that interfaces directly with the ice maker harvest cycle and the auger/dispenser mechanism. Its molded geometry channels released ice from the ice maker into a controlled chute, presents the correct drive coupling depth and alignment for the auger, and provides mounting bosses for the ice-level sensor so the control board receives accurate fullness information. The bucket’s interior finish and wall geometry reduce ice bridging and promote reliable conveyance, while its attachment points establish both mechanical alignment and electrical/sensor clearances required for consistent dispenser operation.
- Mechanical interfaces: auger opening, drive-coupling recess, mounting tabs
- Sensor accommodations: level-sensor boss and routing channels
- Functional surfaces: smooth interior to reduce bridging and frost buildup
- Service indicators: crack, deformation, or misalignment often cause jams or false “full” signals
| Item | Description |
|---|---|
| Function | Collects ice, aligns auger drive, and provides mounting for level sensor |
| Material | Typical food-grade polymer with low thermal mass to help ice release |
| Interfaces | Mechanical tabs, auger opening, and sensor bosses that must match host refrigerator geometry |
| Common service symptom | Ice jamming or false-full readings caused by cracks, warping, or improper seating |
In practical service terms, replacing or inspecting the bucket requires verification of the mounting orientation, auger coupling depth, and sensor boss position rather than assuming universal fit; even small dimensional differences change auger torque and sensor triggers. For example, a bucket missing the proper drive recess will allow the auger to cam out or strip ice, and a warped rim can let ice bind against the auger housing. Routine maintenance includes checking for cracks or deformation, confirming that fasteners and tabs are intact, and cleaning with warm water to remove compacted ice-avoid harsh solvents or abrasive scrubbing that can alter mating surfaces. When ordering a replacement, matching the part number or confirming identical interface dimensions ensures the bucket will behave correctly within the refrigerator’s ice-making and dispensing subsystem.
How the 241734001 Frigidaire Refrigerator Ice Bucket Integrates with the Ice Maker, Motor, and Water Delivery System
The 241734001 Frigidaire Refrigerator Ice Bucket functions as the mechanical and storage interface between the ice maker assembly and the dispensing/collection path. In production refrigerators this bucket receives cubes or flakes from the ice maker mold and, on dispenser-equipped units, transfers them to the chute via an auger or rotating mechanism driven by a dedicated motor. Integration points include a drive coupling or boss that mates with the auger motor shaft, alignment tabs that position the bucket under the ice mold dump, and a fill-level actuator or optical flag that communicates bucket fullness to the ice maker control. For example, a worn drive coupling will allow the motor to run without moving ice, producing an apparent motor fault while the root cause is mechanical slippage in the bucket interface.
- Physical coupling: drive boss/auger engagement for dispensing.
- Positioning: alignment tabs and bosses that ensure proper dump and chute alignment.
- control feedback: fill-level actuator or flag that signals the ice maker to start/stop cycles.
- Behavioral effects: bridging, jamming, or reduced dispense rate when misaligned or damaged.
| Item | Description |
|---|---|
| Ice maker | Dumps formed ice into the bucket; bucket must be seated to receive full dumps without spillage. |
| Auger motor / drive coupling | transfers torque to move ice toward the dispenser; coupling integrity determines dispense reliability. |
| water inlet valve | Supplies water to the ice mold upstream; incorrect water volume or pressure alters cube size and increases jamming risk in the bucket. |
| Fill-level actuator | Mechanical flag or sensor mounted to the bucket provides feedback to stop ice production when full. |
Technically, the bucket itself does not control water delivery or ice formation but influences system performance through its mechanical condition and fit. Operational troubleshooting should address both bucket and upstream systems: inspect the bucket for cracked bosses, stripped coupling teeth, or warped mounting faces; verify the auger motor current draw and that the coupling engages without play; and confirm the ice maker’s fill time and water pressure produce properly sized cubes to avoid compaction inside the bucket. In practice, replacing a damaged 241734001 Frigidaire Refrigerator Ice Bucket or correcting its alignment often resolves dispense failures and false fullness indications without changing electrical components upstream.
Common Failure Symptoms and Diagnostic Indicators for the Ice Bucket (cracking, jamming, misalignment, and moisture intrusion)
the 241734001 Frigidaire Refrigerator Ice Bucket serves as the primary ice storage and transfer interface between the ice maker and dispenser; it locates to the ice-maker housing and engages the auger drive and chute features. Constructed from molded thermoplastic with integrated mounting tabs and an auger bore, the bucket must maintain dimensional integrity and correct tab alignment to permit smooth auger engagement. Cracking typically appears at stress concentration points-mounting ears, the auger bore lip, and corners were impact or freeze/thaw cycles occur-and will permit ice or meltwater to escape the intended flow path, contributing to blockages, abrasive wear of the auger shaft, or progressive deformation of mating features. Compatibility with the refrigerator’s ice-module geometry matters: even small dimensional shifts from a replaced or aftermarket bucket can produce repeat misalignment symptoms despite a healthy auger motor.
Technically observable failure symptoms include mechanical interference during auger rotation, excessive running current on the auger motor, and signs of moisture intrusion such as interior frost layers or pooling meltwater; these indicators guide which repair action is required. Perform a visual inspection under illumination for visible cracks, check axial runout and lateral play of the installed bucket relative to the auger shaft, and measure motor current or listen for increased acoustic noise during a dispense cycle to detect frictional binding. For practical troubleshooting, verify that mounting tabs seat in their slots and that the bucket can be removed and reinstalled without force; trapped ice bridges, dents at the auger bore, or softened plastic from repeated defrost cycling commonly produce the documented symptoms and can be distinguished from electrical faults by observing repeatability and by isolating the motor from the load.
- Cracking: hairline or through-cracks at mounting ears or auger bore-inspect visually and under flex; cracks lead to leakage and accelerated wear.
- Jamming: high motor torque, grinding sounds, or intermittent dispense-check for ice bridges, debris, or deformation at the auger inlet.
- Misalignment: uneven wear on bucket lip or off-center engagement-measure fit of tabs and axial position relative to auger shaft.
- Moisture intrusion: frost buildup, mold, or pooled water-look for compromised seals, cracks, or blocked drainage paths.
| Item | Description |
|---|---|
| Symptom | Likely cause and quick diagnostic action (visual, mechanical, or electrical check) |
| Grinding during dispense | Debris or deformation at auger inlet – remove bucket, inspect bore, rotate auger by hand to locate interference |
| Visible crack at tab | Structural failure from impact or fatigue – replace bucket and confirm tab seating to prevent recurrence |
| Interior frost or standing water | Moisture intrusion from crack or drain blockage – dry, inspect seams, and test after reassembly |
Compatibility, Replacement Considerations, and Step‑by‑Step Installation for the 241734001 Ice Bucket
The 241734001 Frigidaire Refrigerator Ice Bucket is a molded ice-storage bin that couples directly to the ice maker’s discharge and the dispenser/auger assembly. Its critical interfaces are the pivot-hook mounting points, the central discharge aperture that aligns with the auger hub, and the ice-sensor flag used by the ice maker to detect bin fullness. Compatibility depends on matching those geometries and the position of the fullness flag; a bucket with different hook spacing or a displaced aperture can prevent the auger from engaging, cause motor stall, or leave the sensor unable to register ice level. The component is typically high-density polypropylene to withstand freezer temperatures and dimensional tolerances; thermal contraction and repeated mechanical loading at the pivot points are common causes of wear or fracture that will impair operation before the rest of the ice-maker assembly shows symptoms.
Before replacing the bucket verify the OEM part number and visually confirm the pivot hook locations and discharge opening align with the existing freezer chassis. Remove the old bucket by turning the ice maker off, lifting to clear the pivot hooks, and sliding the bin out; install by seating the top pivot hooks, lowering the bin into place until the discharge aperture engages the auger hub and the fullness flag moves freely across its actuator. After installation, run a manual ice-maker cycle and operate the dispenser to confirm the auger engages without binding and the sensor halts production at the correct level. Common checks and installation steps:
- Power/ice-maker off before removal; lift and tilt bucket to disengage pivot hooks.
- Inspect pivot hooks, discharge aperture, and fullness flag for cracks or distortion.
- Seat new bucket’s pivot hooks, ensure discharge opening meshes with auger hub and flag actuates.
- Cycle ice-maker and operate dispenser to verify mechanical engagement and sensor function.
| Item | Description |
|---|---|
| Mounting | Two pivot hooks at top; must match refrigerator hinge geometry for secure seating |
| Discharge Interface | Central aperture aligns with auger hub; diameter and depth effect auger engagement |
| Fullness Flag | Mechanical actuator position determines ice-maker shutoff; must clear flag actuator |
| Common Failures | Cracked pivot hooks, warped aperture, or broken flag leading to dispenser stalls or overfilling |
Q&A
Is part number 241734001 the correct ice bucket for my Frigidaire refrigerator?
241734001 is a Frigidaire OEM replacement ice bucket used in a range of Frigidaire/frigidaire Gallery models. To confirm compatibility, locate your refrigerator model number (usually on a sticker inside the fresh food section or on the cabinet frame), then check the appliance parts diagram or the part listing from Frigidaire or a reputable parts supplier. also compare the shape, mounting tabs and dimensions of the current bucket to the replacement listing.
How do I remove and install the 241734001 ice bucket?
Turn the ice maker off or disconnect power to the refrigerator before servicing. Open the freezer, lift the bucket slightly to disengage any retention tabs, then slide it out straight from the housing. to install, align the bucket’s mounting tabs or tracks with the freezer housing and slide it in until it seats. Restore power and re-enable the ice maker. If your model uses an auger/drive coupling or motor, ensure the bucket engages the drive properly and do not force it.
How should I clean the ice bucket?
Remove the bucket and dump old ice. Wash with warm water and a mild dish soap, rinse thoroughly, and air dry before returning it to service. Avoid abrasive scrubbers or harsh chemical cleaners that can scratch or degrade the plastic. If the manufacturer’s documentation allows it, you may place some plastic buckets on the dishwasher’s top rack, but hand washing is safest.
What common problems affect this ice bucket and how do I troubleshoot them?
Typical issues include cracks or broken tabs,ice bridging/jamming,and poor engagement with the auger or dispenser. Inspect for visible damage or warped mounting features; replace the bucket if cracked. For ice jams, turn off the ice maker, remove the bucket and clear the ice (see next question), then check the auger and drive coupling for damage. If the dispenser motor runs but no ice is delivered, the problem may be the auger, drive motor or switch rather than the bucket.
How do I remove ice that is frozen solid inside the bucket without damaging it?
Power off the ice maker or unplug the refrigerator to prevent motor damage. Let the ice soften naturally or pour small amounts of warm (not boiling) water over the ice to loosen it. Use a plastic or wooden tool to gently break and lift ice-never use metal tools or sharp objects that can crack the bucket. After clearing, dry the bucket wholly before reinstalling.
Is 241734001 an OEM or aftermarket part?
241734001 is an OEM Frigidaire part number. OEM parts are produced to the appliance manufacturer’s specifications. Aftermarket equivalents may be available, but verify fit and quality before purchasing and prefer sellers that allow returns if the part does not fit.
Where can I buy a replacement 241734001 ice bucket and what should I check before buying?
You can buy this part from Frigidaire authorized parts dealers, appliance parts retailers, and many online marketplaces. Before buying, confirm your refrigerator model number and compare the part number, photos and mounting features. Check the seller’s return policy and warranty in case the part is not a correct fit or is damaged.
When should I replace the ice bucket instead of trying to repair it?
Replace the bucket if it has visible cracks that let water/ice leak, broken or missing mounting tabs, severe warping that prevents proper engagement, or if repeated ice jams occur due to distorted geometry. Minor dirt or surface scratches can be cleaned; problems with the auger, motor, or dispenser mechanism generally require service or replacement of those components, not the bucket itself.
Key Takeaways
The 241734001 Frigidaire refrigerator ice bucket serves a straightforward but crucial role in maintaining refrigerator performance and user convenience: it securely stores and dispenses ice, helps preserve ice quality, and interfaces with the ice-making and dispensing mechanisms. As a designed component of specific Frigidaire models, its correct fit and function contribute to efficient ice production, hygienic storage, and prevention of leaks or obstructions that can affect overall appliance operation.
Timely and accurate diagnosis of ice bucket issues is important to determine whether repair or replacement is necessary.Common signs that the bucket may be failing include visible cracks or deformation, improper seating or alignment in the ice compartment, unusual melting or leaking, or interference with the ice maker or dispenser. Confirming the root cause-whether the bucket itself is damaged, an adjacent component has failed, or an installation issue exists-helps avoid unnecessary parts replacement and ensures the right corrective action is taken.
When replacement is required, using the correct part number (241734001) and following manufacturer recommendations helps restore reliable operation, maintain ice quality, and reduce the risk of further damage to the ice-making system. Engaging qualified service personnel or following authorized diagnostic guidance when uncertain will help ensure compatibility, safety, and a cost-effective outcome. Proper diagnosis and replacement preserve appliance performance and extend the useful life of the refrigerator’s ice system.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
