DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM is a factory-original ice maker assembly and associated control/actuator module designed for use in compatible Samsung refrigeration units. Teh designation identifies a complete OEM assembly that typically includes the ice maker motor/actuator, harvest heater or heater element, mounting bracket, and electrical connector configured for 120 VAC operation. As an assembly-level spare, it is intended to be a direct replacement for the factory-installed unit and conforms to the original connector, mounting points and voltage requirements.
Within the appliance, this assembly manages the ice production and harvest cycle inside the freezer compartment. It receives timed control signals or line voltage from the refrigerator control board,drives the ejector motor or actuator to harvest ice from the mold,and may energize a small heater or defrost element to release ice from the mold. The assembly interfaces mechanically and electrically with the ice mold,the water inlet/solenoid valve (for filling cycles),ice-level sensing devices (mechanical arm or optical sensor),and the main control harness. Proper operation depends on correct 120 V supply, intact sensors/switches, and secure mechanical mounting to ensure alignment with the ice mold and discharge chute.
in the following article readers will find a technical overview of how the DA82-02698A assembly functions, how to confirm compatibility with specific refrigerator model numbers, common failure symptoms to watch for (such as no ice production, continuous water flow, failed harvest, or motor hum), and structured troubleshooting checks such as visual inspection, voltage and continuity testing, sensor verification, and water-valve coordination. The article will also cover practical replacement considerations including verifying OEM part numbers and connectors, mechanical fitment and secure mounting, safety precautions (disconnecting power and water before servicing), and post-replacement checks to validate correct cycle operation.
Table of Contents
- Functional Role and Electrical and Mechanical Responsibilities of the A/S Ice/Dispenser Assembly
- How the DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM Operates Within the Refrigerator Ice-Making and Dispensing System
- Common Failure Symptoms, Diagnostic Indicators, and Sensor/Actuator Fault Analysis
- Model Compatibility, Replacement Considerations, and Step-by-Step installation Procedures
- Q&A
- In Retrospect
Functional Role and Electrical and Mechanical Responsibilities of the A/S Ice/Dispenser Assembly
DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM is the integrated ice-maker and dispenser module used in compatible Samsung refrigerator models; it combines the electrical control elements, sensor inputs, and mechanical drive components required to produce, harvest, and deliver ice. Functionally the assembly receives control signals from the refrigerator main board, powers the ice motor/auger and solenoid or actuator for dispense operations, and uses embedded sensors or thermostats to time freeze and harvest cycles. The assembly is designed for a 120V appliance surroundings and must match the refrigerator’s harness and connector pinout to ensure proper voltage routing and safe operation.
- Electrical responsibilities: receive control commands, supply power to motor/solenoid/heater circuits, report sensor/thermostat states to the main board.
- Mechanical responsibilities: rotate or eject ice from the mold, drive the auger or chute for dispensing, maintain water-seal integrity at the inlet and dispense interface.
- Sensors and interlocks: temperature sensing for harvest timing, door and dispenser switches to prevent operation when unsafe, and flow/overflow checks where fitted.
- Compatibility considerations: connector pinout, mounting points, and nominal voltage must match the host refrigerator to avoid misbehavior or damage.
| Item | Description |
|---|---|
| Voltage | Nominal 120V interface for heaters/solenoids; control signals may be low voltage from the main board-verify with schematic. |
| Primary functions | Ice formation, timed harvest, mechanical ejection, and dispense actuation. |
| Common failure modes | Motor/gear wear causing jammed dispense, failed solenoid or heater, bad sensor causing incorrect harvest timing. |
Technicians should distinguish electrical failures from mechanical faults by checking for correct control voltages and continuity at the assembly harness before disassembly; such as, absence of motor voltage with correct control signals indicates a wiring or board issue, while motor voltage present with no rotation points to a seized geartrain or stripped coupling. Practical replacement or troubleshooting steps include confirming connector compatibility, inspecting the auger and gear teeth for wear, measuring coil and heater resistance against manufacturer specifications, and verifying sensor continuity; replacing the DA82-02698A assembly typically resolves combined electrical-mechanical faults such as intermittent dispensing, continuous water flow due to valve control failure, or persistent harvest failures caused by damaged harvest mechanisms.
How the DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM Operates Within the Refrigerator Ice-Making and Dispensing System
The DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM is an OEM ice-maker module that performs the mechanical and thermal operations required to produce and deliver ice within compatible Samsung refrigerator freezers. This assembly combines a molded ice tray, an ejector motor, a melt/harvest heater and the associated switch/actuator interfaces so the refrigerator’s main control board can sequence fill, freeze, harvest and dispense operations. The assembly is driven by the refrigerator harness and uses 120V power for the heater and motor circuits during the harvest cycle; it interfaces with the water inlet valve and the cabinet-mounted ice bin so that fill timing and cube ejection are coordinated with the fridge’s control logic.
Technicians will find the module straightforward to diagnose and replace because its failures produce distinct symptoms: no ice production (heater or motor fault), continuous running (stuck actuator or control fault), or poor cube release (heater failure or mechanical binding). for field service checks, verify that the control board delivers the 120V harvest signal to the assembly during the expected cycle, confirm continuity of the heater and motor windings, and inspect the fill tube alignment and motor gear train for physical blockage. Practical installation notes include correct harness seating, ensuring the ejector arm clears the bin, and confirming model compatibility with DA92 00594M if cross-replacing; the list and reference table below summarize the assembly’s principal features and key technical attributes.
- Mold heater for harvest: loosens cubes for ejection.
- Ejector motor and gears: rotates arms to push cubes into bin.
- Fill control interface: coordinates with refrigerator water valve.
- ice level sensing/actuator: prevents overfilling and signals full-bin condition.
| Item | Description |
|---|---|
| Voltage | 120V supply for heater and motor during harvest |
| Compatible part references | DA92 00594M (cross-reference for compatible Samsung models) |
| Primary functions | Fill, freeze, harvest (heater), eject (motor), and ice-level sensing |
| location | freezer compartment, mounted above the ice bin and connected to refrigerator harness |
Common Failure Symptoms, Diagnostic Indicators, and Sensor/Actuator Fault Analysis
The DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM is an OEM ice-maker assembly that integrates the ice mold, ejector motor/gearing, harvest heater, fill-valve interface, and sensing elements. In service it sequences a fill, freeze, harvest and refill cycle; the harvest stage relies on the heater and a thermostat or thermistor to detect completion so the ejector motor can advance and deliver cubes. Compatibility is primarily with Samsung models designed for a 120V ice-maker module and original mounting/wiring; when replacing this assembly match the harness connector, mounting points and the control signal voltages rather than only the part number to avoid mismatches with different sensor types (thermistor vs. bimetal thermostat) or fill-valve ratings. Practical examples: a unit that produces partial cubes often indicates a faulty thermistor or poor evaporator temperature, while continuous water flow typically points to a stuck or electrically shorted fill valve or a failed water-level switch in the assembly.
Diagnostic indicators for sensor and actuator faults are electrical continuity, DC/AC control voltage presence during cycle phases, measured resistance or temperature readings for thermistors, and visual/mechanical inspection for frozen jams or broken gears. Use a multimeter to confirm coil resistance on the inlet valve, check heater continuity and apply a controlled harvest voltage to observe heater and motor response; verify the thermistor with a known-temperature reference to confirm it reports the expected resistance/temperature curve. Check harness connectors for corrosion or intermittent contacts and observe the assembly during a forced cycle: if the motor turns but cubes remain attached,suspect the heater or heater contact; if the motor does not turn but receives correct voltage,inspect the motor windings and gear train for mechanical failure.
- No ice or slow production - check evaporator temperature, thermistor resistance, and ice-maker fill timing.
- Continuous water flow - inspect fill-valve coil resistance and check the water-level switch or inlet valve driver.
- Partial or misshapen cubes – test harvest heater continuity and verify correct freeze duration/control thermistor readings.
- Motor does not advance - confirm cycle voltage at the motor, then check motor continuity and mechanical gear integrity.
| Item | Description |
|---|---|
| Thermistor / Thermostat | Measure resistance vs. temperature; out-of-spec values indicate faulty sensor or improper freezer temperatures. |
| Harvest Heater | Continuity present across heater; draws expected current during harvest-open or high resistance indicates failure. |
| Fill Valve | Coil resistance consistent with 120V specification and valve closes electrically; stuck or shorted coil causes constant fill. |
| motor / Ejector | Motor should show continuity and respond when cycle voltage is applied; mechanical jams may prevent rotation despite electrical drive. |
Model Compatibility, Replacement Considerations, and Step-by-Step Installation Procedures
The DA82-02698A Samsung A/S Assembly ICE;CD DA92 00594M 120V OEM is an electromechanical ice-maker assembly designed to integrate with Samsung refrigeration control systems that provide a 120 V harvest cycle. This assembly combines the harvest heater, motor/gear train, fill valve interface, and sensor mounts; compatibility depends on matching the part number, connector pinout, and the physical mounting pattern rather than model family names alone. Technicians should verify the harness connector shape, the number of pins and signal assignments (motor, heater, fill solenoid, sensor), and the location of the water inlet and drain/vent tubes. Differences in thermostat or thermistor type, ice thickness adjustment, and trim/door geometry can cause fitment or function issues even when dimensions appear similar, so cross-checking against the refrigerator’s wiring diagram and measuring expected voltages during a manual harvest cycle are practical ways to confirm interchangeability before installation.
Replace and install the ice assembly following safe, verifiable steps that preserve appliance operation and water-tightness: Disconnect power and turn off the water supply before beginning, remove the ice bin and cover, and transfer any model-specific brackets or sensors if required. After mechanical installation and reconnecting the electrical harness and water line, force or run a diagnostic harvest cycle to confirm the motor spins, the heater receives ~120 V during harvest, the fill valve opens for the expected duration, and no leaks appear at the inlet or drain. Common troubleshooting items to check after installation include continuity of the heater element, correct sensor placement for temperature feedback, and unobstructed ejector movement; if the assembly does not harvest correctly, re-check connector pin assignments and control-board outputs rather than assuming a defective module.
- Safety first: disconnect power and shut off the water supply.
- Remove ice bin and any trim to access the assembly cover and mounting screws.
- Disconnect electrical harness and water inlet, noting connector orientation and pinout.
- Remove old assembly, transfer sensors/brackets if needed, and secure the new assembly to existing mounting points.
- Reconnect harness and water, restore power, and force a harvest cycle; verify heater gets ~120 V and motor rotates.
- Check for leaks, proper fill volume, and enable normal operation; allow up to 24 hours to normalize ice production.
| Item | Description |
|---|---|
| Part number | DA82-02698A / DA92 00594M (OEM replacement) |
| voltage | 120 V AC harvest heater and motor drive (verify on-site) |
| Connectors | Multi-pin appliance harness-match shape and pin assignments to refrigerator wiring diagram |
| Mounting | model-specific bracket locations; confirm hole spacing and sensor positions |
Q&A
What is the DA82-02698A / DA92-00594M 120V OEM part and which refrigerators use it?
DA82-02698A (also listed as DA92-00594M) is an OEM ice maker assembly (A/S Assembly ICE;CD) used in many Samsung refrigerator freezers. It is indeed the complete ice-making module (motor, harvest heater, ejector, fill cup and mounting) designed for Samsung models that accept a 120V ice maker. Compatibility depends on the refrigerator model number – verify with your fridge’s model or Samsung parts lookup to ensure fit. Do not assume interchangeability across different chassis without checking fit/connector and mounting points.
What symptoms indicate this ice maker assembly is faulty and needs replacement?
Common signs include: no ice production, ice not ejecting or stuck in the mold, continuous motor hum with no movement, visible water leaking or overflowing into the bin, partially formed/very small ice cubes, or the harvest heater failing to melt ice (resulting in clumped ice). Before replacing, confirm water supply, inlet valve, and the freezer’s temperature are correct, since those issues can mimic ice maker failure.
How do I safely replace the DA82-02698A ice maker assembly?
Turn off power to the refrigerator and shut off the water supply. Remove the ice bin and any interior panels blocking access. Disconnect the ice maker wiring harness and water fill tube (if applicable). Remove the mounting screws and take out the old assembly. Install the new DA82-02698A in the same position,secure with screws,reconnect the harness and fill tube,restore power and water,then run a test/fill cycle. Always use basic safety: unplug or switch off the circuit breaker and avoid forcing connectors or tubing.
What tools and test equipment do I need for installation and troubleshooting?
Typical tools: Phillips screwdriver or nut driver set (depending on screw type), pliers, and a flashlight. For troubleshooting: a multimeter to check for 120VAC at the ice maker connector and continuity of heater/motor circuits, and optionally a small mirror or inspection camera for hard-to-see areas. if you need to manually initiate a harvest cycle, a thin insulated jumper or a service mode (if available) may be used per model instructions.
How can I test the ice maker before or after installation to confirm it’s working?
After reconnecting power, listen for the motor or gear noise when a cycle starts. Use a multimeter to verify ~120VAC is present at the ice maker harness during the fill/harvest cycle. Check heater continuity (should not be an open circuit) and motor windings for continuity.You can also manually initiate a harvest (via the refrigerator’s diagnostics or service procedures) to see if the heater melts ice and the ejector cycles. Confirm a water fill occurs after the ejector cycle and that ice forms in the mold over the next several hours.
Can I repair parts of the ice maker (heater, motor) or should I replace the whole assembly?
Minor repairs (replacing a plug or removing ice jams) are possible, but the common OEM approach is to replace the entire ice maker assembly. The harvest heater, motor and molded plastic components are integrated, and replacing the assembly is usually faster, more reliable and preserves factory sealing and alignment. If you have electronic/motor skills and replacement components, you can repair individual parts, but OEM replacement minimizes downstream issues.
Why is the part specified as 120V crucial and what should I check electrically?
The DA82-02698A is designed for 120VAC operation. Ensure your refrigerator’s ice maker circuit provides 120VAC at the connector; many Samsung units supply mains-level voltage for the heater and motor. Using the wrong-voltage part can damage the assembly or be unsafe. Before installation, measure voltage at the ice maker harness with the unit powered (take proper precautions). If there is no 120VAC present, check refrigerator electronics, control board, or wiring harness for faults.
How long does replacement take and are there common installation pitfalls?
A straightforward replacement typically takes 15-45 minutes for someone comfortable with appliance work. Common pitfalls: not fully removing power/water first, failing to seat the fill tube or sealing grommet (causing leaks), incorrect orientation/misaligned mounting (causing ice jams), not running an initial test cycle after installation, and ignoring a clogged water inlet filter or faulty water valve – those will continue problems even with a new ice maker. Always verify model compatibility and that the connector and mounting holes match before starting.
In Retrospect
The DA82-02698A (A/S Assembly ICE;CD DA92-00594M 120V OEM) serves as a factory-designed ice-making and control assembly intended to maintain reliable ice production and proper system operation in compatible Samsung refrigeration units. As an OEM component,it is engineered to meet the original equipment specifications for electrical compatibility,mechanical fit,and overall performance,which helps preserve the appliance’s intended function and safety characteristics.
Accurate diagnosis is essential before replacement: confirming the root cause of ice production or control issues (electrical faults, sensors, mechanical wear, or installation errors) prevents unnecessary parts changes and recurring failures. When replacement is required,using the correct OEM part and following manufacturer-recommended installation and safety procedures helps ensure compatibility,reduces the likelihood of additional damage,and supports warranty and service expectations.
the DA82-02698A assembly plays a key role in the continued performance of the appliance, and thoughtful troubleshooting combined with proper replacement practices will deliver the best outcomes for reliability, safety, and long-term serviceability.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
