DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM is an original-equipment ice-making assembly intended for use in compatible Samsung refrigeration units. The assembly is a combined mechanical and electrical module that typically includes the ice mold and harvest mechanism, drive motor or actuator, associated switches and sensors, and the electrical connectors required for integration with the refrigerator control system; the 120V designation indicates the nominal operating voltage for the drive/heater circuits on models that use line-voltage components.
Within the appliance the assembly governs the ice production cycle, coordinating water fill, freeze dwell time, harvest actuation and ice discharge.It interfaces with the refrigerator’s control board and temperature sensors for timing and state detection,the water inlet/valve for fill control,and the ice storage/dispenser mechanism for delivery. Proper function requires correct electrical supply, signal timing from the main control, and correct mechanical alignment with the ice bin and mold; failures in any of these interfaces can lead to no-ice, overfill, leakage, or mechanical jam conditions.
This article will describe the assembly’s functional elements and electrical requirements, outline model compatibility and cross-references to aid part selection, summarize common failure symptoms to help diagnose issues, and present practical troubleshooting checks a technician or informed appliance owner can perform. It will also cover replacement considerations such as connector and harness matching, mounting and alignment notes, safety precautions when working with line-voltage components, and calibration or initialization steps typically required after installation.
Table of Contents
- Function and Role of the Ice Maker A/S Assembly in Samsung refrigerator Ice Production
- How the DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM Operates Within the Refrigerator Cabinet
- Common Failure Symptoms and Diagnostic Indicators for the Ice Maker A/S Assembly
- replacement Considerations, Installation Steps and Electrical Requirements for the Ice Maker A/S Assembly
- Q&A
- In Retrospect
Function and Role of the Ice Maker A/S Assembly in Samsung Refrigerator Ice Production
The DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM is the integrated ice-maker module that coordinates the mechanical and thermal steps of ice production in compatible Samsung refrigerator models. This assembly contains the drive motor and cam, the ice mold and heater circuit for controlled harvest, the fill-valve interface, and the level/thermistor sensing elements; the control board supplies a 120V feed for the heater and provides low-voltage drive and sensing connections for the motor and sensors. In operation the assembly sequences a fill pulse, a freeze interval monitored by the thermistor or timed cycle, and a harvest/eject phase in which the heater and motor work together to loosen and eject cubes; proper function depends on correct electrical connection, intact sensors, and unobstructed mechanical parts.
Technicians diagnose issues with this assembly by isolating electrical signals, measuring resistance of heaters and motors, and visually inspecting the cam, ejector fingers, and ice mold for damage or icing that inhibits movement.Common service actions include verifying 120V heater supply at harvest, checking continuity and motor rotation at the harness while the board commands a harvest, and confirming the water fill valve operates during the fill step; replacement with the OEM DA82-02702A / DA92 00593M assembly restores original mechanical tolerances and sensor placement for models listed as compatible. Practical troubleshooting cues and replacement considerations are summarized below.
- Symptom: no ice production – check water supply, fill valve operation, and thermistor readings before replacing the assembly.
- Symptom: ice stuck in mold or incomplete harvest – inspect heater continuity, motor torque, and ice mold for scale or mechanical binding.
- Verification steps: measure heater voltage during harvest cycle, command motor via service mode, and test thermistor resistance over temperature.
- Replacement tip: match OEM part numbers and harness connector style to avoid cross-compatibility issues.
| item | Description |
|---|---|
| Voltage | 120 V AC heater supply with low-voltage control signals for motor and sensors |
| Primary functions | water fill control interface, timed/thermistor-based freeze, mold heating for harvest, motor-driven ejection |
| Compatibility | OEM assembly for specified Samsung refrigerator models; verify DA82-02702A / DA92 00593M match against unit model number |
How the DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM operates Within the Refrigerator Cabinet
The DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM is the electromechanical ice-making module that coordinates water metering, freezing, and ejection inside the freezer compartment. The assembly typically contains a motor-driven ejector or auger, a water fill cup or valve interface, a low-voltage thermostat or thermistor to sense mold temperature, and a harvest heater (or heater circuit) that softens ice for release. During a cycle the control board applies 120 V to the module at defined intervals: the fill phase meters a measured volume of water into the mold, the freeze phase allows the evaporator to remove heat until the sensor indicates frozen conditions, and the harvest phase activates the heater and motor to release cubes into the storage bin.Proper operation depends on secure mounting near the evaporator,correct alignment of the fill tube and mold,and matching electrical and connector configurations to the refrigerator’s harness and control board.
Technically, this assembly behaves as a coordinated subsystem whose failure modes are distinct and diagnosable by voltage, continuity, and resistance checks. Common issues include motor or heater open circuits, a stuck fill cup or valves causing flooding, and faulty temperature sensing that prevents harvest or causes premature cycling. For practical troubleshooting, verify that the module receives the expected supply signals from the main control, check continuity of the motor and heater circuits, inspect the fill tube for ice blockage, and confirm the resistance values of the sensor against manufacturer specifications before replacing the unit. Use this assembly only in cabinets that accept its connector pinout and 120 V rating; substituting a unit with different voltage or harness layout can cause improper cycles or electrical damage.
- No ice produced - check for 120 V at the module connector, inlet valve operation, and mold temperature sensor continuity.
- Continuous fill or overflow – inspect the fill cup, valve seating, and control signal timing from the main board.
- Ice not ejecting – test motor and harvest heater continuity and ensure the ejector has no mechanical obstruction.
| Item | Description |
|---|---|
| Voltage | 120 V AC supply for motor/heater circuits (verify model label) |
| Mounting | Freezer compartment, adjacent to evaporator and ice storage bin |
| Connectors | OEM multi-pin harness; match pinout to refrigerator control board |
| Key components | Fill interface, motor/ejector, mold sensor (thermistor/thermostat), harvest heater |
Common Failure Symptoms and Diagnostic Indicators for the Ice Maker A/S Assembly
The DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM is the integrated ice-making mechanism used in several Samsung refrigerator lines; it combines the water inlet/solenoid, fill cup, mold heater, thermistor, and drive motor assembly into a single replaceable module. In normal operation the assembly controls timed fill and freeze intervals, senses mold temperature to initiate harvest, and uses a heater/rotation sequence to eject ice into the bin. Compatibility with the host PCB and correct 120V supply are critical-mismatched voltage, connector pinout, or firmware differences on the main control board will produce predictable failures such as missed harvests or continuous fill conditions rather than mechanical problems inside the module itself.
Technicians evaluate failure using symptom-driven checks and electrical measurements: confirm the presence of the control voltage at the module connector during a commanded fill/harvest, verify solenoid coil and heater continuity, and measure thermistor response across temperature change. Mechanical indicators-grinding noises, motor stall, or broken ejector fingers-point to internal wear or obstruction, while steady drip or overflowing indicates valve or inlet issues. The list below summarizes common observable symptoms technicians use to triage faults, and the table provides speedy reference pairing symptoms with typical diagnostic checks and likely component-level causes.
- No ice production: unit does not cycle into fill or freeze-check control voltage, connector pins, and LED error codes on the refrigerator PCB.
- Small or hollow ice cubes: incomplete fill or fast harvest-inspect water pressure, solenoid function, and fill cup alignment.
- Ineffective harvest or sticky cubes: heater or thermistor malfunction-measure heater continuity and thermistor resistance change with temperature.
- continuous water flow/overflow: solenoid stuck open or control signal failed-verify solenoid coil resistance and apply manual actuation test.
- Unusual noise or motor stall: mechanical failure in drive train-inspect motor shaft, gears, and ejector assembly for wear or foreign objects.
| Item | Description |
|---|---|
| No ice, no cycle | Check for 120V control present at module during expected harvest/fill; verify harness continuity and main board commands before replacing assembly. |
| Insufficient fill / thin cubes | Inspect water inlet pressure, filter condition, and solenoid operation; measure solenoid coil for continuity and test fill cup sealing. |
| Incomplete harvest / cubes stuck | Measure heater continuity and thermistor temperature response; if heater open or thermistor out of range, replacement of the module is indicated. |
| Water leak or overflow | Check solenoid for proper closure, and inspect fill cup and drain paths; electrical command should be confirmed to rule out control board faults. |
Replacement Considerations, Installation Steps and Electrical Requirements for the Ice Maker A/S Assembly
The DA82-02702A Samsung A/S Assembly ICE;FS DA92 00593M 120V OEM is a self-contained ice-maker assembly that integrates the fill/solenoid interface, harvest heater, ice mold and the drive motor/gearpack. In normal operation the module senses mold temperature, commands the water fill and then executes a timed freeze and harvest sequence; failures typically present as no fill, continuous fill, or failure to eject ice. Replacement compatibility is steadfast by mechanical mounting points, harness connector shape and pinout, and the 120 V operating characteristic; confirm that the replacement assembly matches the original part number and wiring harness before installation to avoid mismatched control signals or improper grounding. Such as, a unit with identical mounting geometry but a different harness pinout can power the motor while leaving the heater or solenoid unpowered, producing symptoms that mimic electrical failure rather than a mechanical defect.
Installations require basic electrical verification, water-line handling and mechanical alignment. Begin by powering down the refrigerator and shutting off the water supply, then remove the evaporator cover to access the assembly; transfer any required brackets or thermistor clips from the old unit to the new one if they are not supplied. Use a multimeter to check continuity of the motor, heater and solenoid against the service manual values and verify the wiring harness pinout before applying power. The assembly is designed for 120 V AC operation on a standard kitchen branch circuit (typically 15 A); because the harvest heater can draw a brief load, ensure the branch circuit and refrigerator grounding are intact and that the supply is protected by the correct breaker or fuse. After mechanical fastening and reconnection of the water line,run a manual harvest/fill cycle to verify correct sequencing and check for leaks and proper ice release.
- Safety first: disconnect mains and water supply before starting.
- Verify part number and harness pinout against the refrigerator schematic.
- Check motor, heater and solenoid continuity with a multimeter before installation.
- Secure mounting brackets and confirm thermistor/clip placement for accurate temperature sensing.
- Restore power and water, then initiate a test harvest cycle and inspect for leaks and correct operation.
| Item | Description |
|---|---|
| Part number | DA82-02702A / DA92-00593M – confirm exact match to refrigerator model |
| Voltage | 120 V AC supply; typically served by a 15 A branch circuit |
| Connector | OEM multi-pin wiring harness – verify pinout and wire colors against service documentation |
| Mounting | bracket and screws; retain original fasteners or replace with identical hardware |
Q&A
What is the DA82-02702A / DA92-00593M ice maker assembly and what refrigerators is it compatible with?
The DA82-02702A (also referenced with DA92-00593M) is an OEM Samsung automatic ice maker assembly for refrigerators. It replaces the entire ice-making module (motor, mold, fill tube interface and internal wiring) used in a range of Samsung top- and bottom-freezer and side-by-side refrigerators. Compatibility depends on yoru refrigerator model and manufacture date – always verify the replacement part number against the model number on the appliance’s rating tag or consult Samsung’s parts lookup to confirm fit.
Does this ice maker run on 120V and can it be used in 240V locations?
Yes - the assembly is designed for standard North American household supply (120VAC, 60Hz). It must be used only on a 120V circuit. Connecting it to 240V will damage the unit and create a fire/electrical hazard. If you have a different supply voltage, you must use the correct part specified for that voltage or a properly rated transformer and a qualified technician.
How do I know the ice maker is bad and needs replacement rather than a simple repair?
Common signs that the ice maker assembly itself is faulty include: no ice production despite proper water supply and working inlet valve; motor not turning or loud grinding coming from the module; repeated production of partial/ malformed cubes; or the ice maker not cycling during diagnostics. If the inlet valve, water supply, control board, and temperature are confirmed good, and the ice maker motor/heater shows open circuits or visible damage, replacement of the assembly is warranted.
Can I install this part myself and what safety precautions should I take?
Technically yes, a competent DIYer can replace the assembly, but you must disconnect power and the water supply before starting. Typical steps: remove the ice bin, unplug the fridge or switch off the breaker, remove mounting screws, disconnect the electrical connector, swap the assembly, reconnect, and re-secure.Avoid forcing connectors, do not splice wires, and ensure the unit is mounted level.If you are uncomfortable working with electrical parts or the heater/motor, hire a qualified appliance technician.
How do I test the new ice maker after installation to make sure it’s working?
After reconnecting power and water, run the fridge through its ice maker diagnostic cycle (if the model supports it) or allow up to 24 hours for the ice maker to fill and begin a harvest cycle.You can also check for proper operation by observing a manual test mode: the ice maker motor should actuate and the fill cup should receive water during the fill step. For electrical tests, with power OFF, a multimeter can check continuity of the motor/heater windings (they should not be open). When powered in a test cycle, you should see ~120VAC at the ice maker’s supply pins during motor operation – only perform live tests if you are trained and use appropriate safety gear.
What tools and parts are typically needed to replace this Samsung ice maker assembly?
Common tools: Phillips/hex screwdrivers, nut driver set, multimeter (for checks), towel/absorbent bucket for small water spills, and needle-nose pliers for connectors. Replacement is the OEM assembly itself; in most cases you won’t need additional parts unless mounting hardware or the connector/harness is damaged. If the water inlet valve or supply tubing is old, consider replacing those parts simultaneously occurring.
Will I lose any settings or need to reset the refrigerator after replacing the ice maker?
Replacing the ice maker itself does not typically change refrigerator settings. Some Samsung refrigerators require running a diagnostic or ice maker test cycle to initialize the new unit; others will self-start after power-up. If your model has a control board or dispenser control with an ice maker enable/disable setting,confirm the ice maker is enabled. If you experience errors after replacement, clear codes by power-cycling the refrigerator or consulting the service manual for the model.
Is this an OEM part and does it come with a warranty?
DA82-02702A / DA92-00593M is an OEM Samsung part number. When purchased from authorized Samsung parts dealers or reputable retailers,it should be a genuine OEM assembly. warranty terms vary by seller – manufacturers typically offer a limited warranty on replacement parts (commonly 90 days to 1 year through the seller or Samsung’s parts program). Keep your receipt and part number and check the specific warranty terms at the time of purchase.
In Retrospect
The DA82-02702A Samsung A/S Assembly ICE;FS DA92-00593M 120V OEM serves as a purpose-built component in compatible Samsung refrigeration systems, contributing to reliable ice production and coordinated operation within the freezer assembly. As an OEM part specified to 120V, it is designed to meet the original equipment manufacturer’s standards for fit, function and safety, helping to maintain expected performance, energy efficiency and system longevity when installed as intended.
Because symptoms such as intermittent ice production, unusual noises or electrical faults can arise from multiple sources, accurate diagnosis is essential before replacing this assembly. Proper troubleshooting and verification of the underlying cause prevent unneeded part changes and reduce the risk of recurring issues. When replacement is needed, using the correct DA82-02702A / DA92-00593M OEM assembly and engaging qualified service personnel ensures a safe installation, preserves appliance reliability and supports long-term performance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
