DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM is an automatic ice maker assembly for Samsung refrigeration appliances. It is an electromechanical subassembly that typically includes the ice mold, ejector/auger or harvest mechanism, motor and gearbox, a harvest heater or defrost element, temperature sensing (thermostat or thermistor), the water inlet interface and associated mounting hardware and wiring harness. Physically located in the freezer compartment or the freezer door in dispenser-equipped units, this component produces, releases and delivers ice cubes on a timed and temperature-controlled cycle.
Inside the appliance the ice maker controls the sequence of filling, freezing and harvesting ice and interfaces directly with the refrigerator’s water supply, the main control board and any dispenser actuators or door interlocks. It depends on the freezer temperature and water pressure to complete a cycle, uses a sensor to determine when freezing is complete, and uses electrical commands from the control board to run the motor and activate the harvest heater or release mechanism. Proper operation therefore requires correct electrical connections, unobstructed water flow, functional sensors and correct mechanical alignment within the ice compartment.
In this article readers will find a technical explanation of the ice maker’s function, guidance on model and part-number compatibility, common failure symptoms and how to distinguish mechanical, hydraulic and electrical faults. The content will cover step-by-step troubleshooting checks (visual inspection, continuity and voltage checks, water pressure and fill timing verification), diagnostic tests for sensors and heaters, and practical replacement considerations such as verifying harness and mounting compatibility, sealing and routing of the fill tube, and basic safety precautions (disconnecting power and water). The goal is to equip technicians,engineers and appliance owners with the information needed to diagnose,repair or replace the assembly with correct technical judgment rather than promotional claims.
Table of Contents
- Functional Role and Operational Requirements of the Ice Assembly
- How the DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM Works Inside the Appliance
- Common failure Modes and Diagnostic Symptoms of the Ice Assembly
- Compatibility, Replacement Considerations, and OEM Installation Guidelines
- Q&A
- future Outlook
Functional Role and Operational Requirements of the Ice Assembly
The DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM is an ice maker assembly designed to perform the full ice production cycle-metered water fill, controlled freeze period, harvest initiation, and mechanical ejection-while interfacing with the refrigerator’s harness and control board. The unit contains the ice mold, a harvest heater or heater traces, a motor/gear train for the ejector, and sensor inputs (thermostat/thermistor or switch) that tell the control board when to advance cycles. When replacing this assembly, ensure the replacement matches the connector pinout, mounting points, and sensor type of the original; a mismatch in connector wiring or sensor behavior will prevent proper cycle sequencing even if the assembly physically fits the cavity.
Operational requirements for reliable performance include a stable cold compartment temperature, an adequate and steady water supply, and correct wiring to the refrigerator control board. Typical operational behaviors: the control board energizes the fill valve for a measured interval, allows the mold to freeze for the defined time, then applies the heater and runs the motor to remove ice. troubleshooting commonly focuses on four areas: power continuity to the motor and heater, correct sensor resistance or switch activation, water inlet operation, and proper mechanical alignment of the ejector. For practical testing,verify harness continuity and motor/heater resistance with a multimeter,confirm the water inlet supplies nominal flow under pressure,and observe whether the assembly completes a full harvest cycle without binding or excessive noise.
- Key components: mold, heater/harvest element, motor/geartrain, thermistor/thermostat or switch, and electrical connector.
- Compatibility checks: matching connector pinout, mounting holes, and sensor type to the refrigerator model before installation.
- Common symptoms of failure: no harvest (heater or motor open), continuous fill (faulty sensor or board), partial ejection (worn gears or jammed ejector).
| Item | Description |
|---|---|
| Mounting / Connector | OEM-style mounting points and multi-pin connector required for mechanical fit and control signal compatibility. |
| Key Components | Thermistor/thermostat for freeze detection, heater for harvest, motor/geartrain for ejection; each should be testable for continuity. |
| Common Failure Modes | Open heater/motor circuits, failed sensors, clogged water inlet or mechanical obstruction preventing ejection. |
How the DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM Works inside the Appliance
DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM is an OEM ice-maker assembly that houses the mechanical and thermal elements responsible for producing and ejecting ice in compatible Samsung refrigerators. The assembly integrates an ice mold, a harvest heater, a thermostat or thermistor for cycle timing, an ejector motor/geartrain, and the electrical connector that interfaces with the refrigerator control board and water valve. During a normal cycle the thermostat senses when ice has frozen, the control board energizes the harvest heater to loosen ice from the mold, then drives the motor to eject cubes into the bin and signals the water valve to refill the mold. The part numbers identify the specific mechanical mounting, connector pinout, and control behavior, so replacements must match those physical and electrical characteristics to operate correctly in the appliance.
Functionally, the assembly behaves as a coordinated sequence of freeze/harvest/fill actions driven by temperature feedback and timed motor activation; failures typically appear as no ice production, continuous harvest, or mechanical noise during ejection. Compatibility depends on matching the mounting points, harness connector, and the refrigerator’s control signals-substituting a visually similar unit without verifying the DA82-02670A/DA94-02963A FS 120 details can result in mismatched timing or improper heater control. For practical troubleshooting, verify power and control signals at the connector, check heater and thermostat continuity with a multimeter, and confirm the water valve and fill cup alignment; replacing the assembly is usually straightforward when the replacement matches the original part number and connector orientation.
- Typical cycle phases: freeze (mold fills and freezes), harvest (heater activates), eject (motor turns ejector), refill (water valve opens).
- Common symptoms and speedy checks: no ice (water valve or fill cup alignment), stuck ice (heater/thermostat), noisy ejection (worn motor/gears).
- Replacement considerations: ensure identical connector pinout, mounting bracket alignment, and OEM part number match.
| Item | Description |
|---|---|
| Part number | DA82-02670A / DA94-02963A FS 120 - OEM ice-maker assembly |
| Primary function | Manage ice freeze/harvest/eject cycles and interface with water valve and fridge control board |
| Diagnostic checks | verify heater/thermostat continuity, motor activation during harvest, and proper water fill operation |
Common Failure Modes and Diagnostic Symptoms of the Ice Assembly
The DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM is the complete ice-maker module that controls water fill, freezing, and harvest cycles in compatible Samsung refrigerator cabins. In normal operation the assembly times and actuates a water inlet valve to fill the mold, monitors freeze completion with a thermostat or thermistor, then drives an auger or ejector mechanism and an internal heater to release ice into the bin. Compatibility is limited to models that accept these OEM assemblies; mating connectors, mounting points, and control signals must match the refrigerator harness and main control board. Common field symptoms technicians will observe include mechanical stalling,intermittent harvest,or continuous fill that indicate specific subsystem faults or mismatched replacement parts:
- No ice produced while the module cycles normally (empty mold or repeated refill).
- Ice cubes are small, misshapen, or spongy, indicating poor freeze time or low water pressure.
- Continuous water flow into the mold or overflow, suggesting a failed fill valve or stuck inlet solenoid.
- Motor hums or clicks but the auger does not turn, often caused by stripped gears, a slipped clutch, or jammed ice.
- Excessive frost or large ice blocks forming, pointing to defrost/heater failure or blocked drainage.
Diagnosing failures requires separating mechanical, electrical, and hydraulic causes. Mechanically inspect the auger, cam, and gear train for wear or broken teeth and manually rotate the motor shaft to confirm free movement; binding indicates internal ice jam or seized bearings. Electrically, verify supply to the module and to individual components: check continuity across the heater/thermostat circuit, measure thermistor or NTC resistance against the service manual reference at ambient temperature, and confirm the fill-solenoid coil resistance and actuation when commanded. Hydraulic issues are usually low inlet pressure, clogged filter, or a leaking valve; measure inlet pressure and observe fill duration during a manual fill cycle. Use the quick-reference table below to correlate failure modes with diagnostic checks commonly performed in the field.
| Item | Description |
|---|---|
| Motor/auger stall | Listen for hum without rotation; inspect gears for damage and measure motor supply while commanded. |
| Thermostat/thermistor fault | Measure resistance at ambient and compare to service values; replace if open or out-of-range. |
| Continuous fill/overflow | Verify valve coil resistance, check for proper control signal from board, and inspect inlet for debris or pressure loss. |
Compatibility, Replacement Considerations, and OEM Installation Guidelines
The DA82-02670A Samsung A/S Assembly ICE;DA94 02963A FS 120 OEM is an integrated ice-making assembly that combines the ice mold, harvest heater, fill valve interface and control harness into a single service replaceable unit. Functionally, the assembly controls the fill-measure-harvest cycle through a small control board and a temperature or position sensor, and it must match the fridge’s harness pinout, mounting flange pattern, and water inlet orientation to operate correctly. Technicians should verify the cabinet model and service tag against the part number before ordering; physical differences such as connector keying, mold geometry, or heater placement will cause intermittent harvest failures or mechanical interference even when the part appears visually similar.
- Verify OEM part number and cross-reference with the refrigerator service sticker before replacement.
- Confirm electrical connector pinout and presence of required grounding or shielding on the harness.
- Inspect and replace the water inlet tubing and check valve to prevent leaks and fill issues after install.
- Perform a manual diagnostic fill/harvest cycle after installation to validate thermostat/sensor behavior and heater function.
During installation, follow OEM guidelines for torque on mounting screws, correct orientation of the mold relative to the ejector arm, and secure routing of the water line to prevent kinks; improper mounting can change the sensor response or allow the mold to rub against the bin, causing noise or ice jam. If the refrigerator uses a shared control board or has firmware-based diagnostics, note that failure modes (no harvest, partial fill, repeated retries) can stem from wiring faults, insufficient inlet pressure, or a mismatched thermostat curve rather than the mechanical ice mold itself, so isolate mechanical, electrical, and supply-side causes sequentially. After replacement, run a full cycle and visually inspect harvest and fill timing; document the outcome and any pinout differences for future service records.
| Item | Description |
|---|---|
| Part number | DA82-02670A / DA94 02963A – confirm exact match with service tag and factory cross-reference |
| Function | Ice mold, heater, fill valve interface and control sensor module |
| Connector | Multi-pin harness – verify pinout and locking tab orientation |
| Mounting | Flange pattern and screw torque affect alignment and sensor accuracy |
| Electrical | Low-voltage control: verify continuity and correct voltage during harvest cycle |
Q&A
What exactly are parts DA82-02670A and DA94-02963A and what do they do?
DA82-02670A is a Samsung ice maker assembly (A/S Assembly ICE) used in many Samsung refrigerators to form, harvest and eject ice. DA94-02963A is an OEM reference/assembly number frequently enough associated with the same or related ice maker subassembly (FS 120 indicates an internal factory code). Together they refer to a genuine Samsung ice-maker module and related harness/parts rather than an aftermarket component. If you need to confirm fitment, always cross‑reference these numbers with your refrigerator model number.
How do I know if the ice maker assembly (DA82-02670A) has failed?
Common failure symptoms include: no ice production,constant noisy motor,ice tray not filling with water,ice clumping/overflowing,or ice not ejecting. Perform basic checks first: ensure the refrigerator/freezer temperature is in the correct range (around -18 °C/0 °F), confirm the water supply is on and filter isn’t clogged, and that the freezer door seals properly. If those are OK,test the ice maker itself with a multimeter for continuity on the heater/thermostat and motor,and verify it receives control voltage during a cycle (refer to service documentation). If internal components show open circuits or the motor does not run when commanded, the assembly likely needs replacement.
Can I replace DA82-02670A myself and what tools/precautions are needed?
Yes, a competent DIYer or technician can replace it, but follow safety precautions: disconnect power to the refrigerator and shut off the water supply before starting. Typical tools: screwdriver set (Phillips and torx depending on model), pliers, and a multimeter. Remove freezer shelving/panels to access the ice maker, unplug the wiring harness, remove mounting screws, swap the assembly, reconnect wiring and water, then restore power. If you are not pleasant working near electrical components or plumbing, hire a qualified appliance technician.
How do I test the new ice maker after installation?
After installation and reconnecting power and water, allow the unit time to refill and reach operating temperature. Most Samsung ice makers have a test/manual harvest feature: either a test button on the assembly or a service diagnostic mode on the fridge control panel. Initiate the ice-maker test/harvest per the service manual and observe: the fill valve should open and water should fill the tray, the motor should rotate to eject ice during harvest, and the heater (if present) should cycle. Also listen for running water and motor activity. If unsure of the procedure for your model, consult the refrigerator’s service manual or Samsung support.
How do I diagnose water fill or ice clumping problems related to this assembly?
For no fill: check that the inlet water valve has supply pressure and is receiving the control signal during a fill cycle. Inspect the water line for kinks and the water filter for blockage. For partial fills or undersized ice: verify water pressure is within Samsung’s specification (low pressure causes small or no fills) and that the fill cup/nozzle on the ice maker is unobstructed. For clumping/jammed ice: check freezer temperature (too warm or fluctuating temps cause soft/clumped ice) and remove old ice to allow normal shape formation. Also inspect the ice-maker heater/thermostat if ice is not detaching properly during harvest.
what electrical checks should a technician perform on this ice maker assembly?
With power off, check continuity of the internal components (motor, thermostat/thermistor, and heater if present) with a multimeter to ensure they are not open. With power on and the unit in a test cycle, verify that the control board is supplying the correct signals to the harness (voltage pulses to the fill valve and motor). always consult the schematic/service manual for the specific model to know expected voltages and harness pin functions. If control signals are present but the component does not operate, the ice maker assembly is faulty; if signals are absent, the control board or wiring is the likely issue.
Are there differences between OEM DA82-02670A and aftermarket replacements? Is OEM necessary?
OEM parts like DA82-02670A are manufactured to Samsung’s specifications and will match fit, electrical connectors and performance exactly. Aftermarket replacements might potentially be cheaper but can differ in materials, dimensions, connector type, or reliability. Using OEM reduces the risk of fitment or electrical incompatibility and maintains factory warranty considerations. For long-term reliability and correct operation it’s generally recommended to use an OEM part when available.
Where can I buy the DA82-02670A / DA94-02963A and what should I check before ordering?
OEM parts are available through Samsung parts distributors, authorized appliance parts retailers, and reputable online parts stores. Before ordering, verify your refrigerator model number (usually on a label inside the fridge or on the door frame) and cross‑reference it with the part number to confirm compatibility. Check that the seller lists the part as genuine OEM and offers a returns policy/warranty. If uncertain, provide your fridge model number to the parts supplier or Samsung support for confirmation.
Future Outlook
The DA82-02670A Samsung A/S Assembly ICE and DA94 02963A FS 120 OEM are OEM replacement components that serve a central role in maintaining the ice-production and related operational functions of compatible Samsung refrigeration systems. By ensuring proper mechanical fit, electrical connectivity, and integration with control and sensor circuits, these assemblies support consistent ice production, reliable water flow, and overall appliance performance.
Timely and accurate diagnosis is essential when symptoms such as reduced ice output, intermittent operation, leaks, unusual noises, or diagnostic error codes appear. A methodical troubleshooting process – verifying power and water supply, checking diagnostics and sensors, and isolating the faulty subsystem – reduces unnecessary part changes and targets the true cause of the problem. When replacement is warranted, selecting the correct OEM part numbers (DA82-02670A Samsung A/S Assembly ICE; DA94 02963A FS 120 OEM) and following manufacturer installation and safety guidelines helps preserve compatibility, warranty considerations, and long-term reliability. Professional installation and post-replacement testing are recommended for optimal results.
these assemblies are important elements in maintaining refrigerator functionality; prioritizing thorough diagnosis and using proper OEM replacements when needed helps protect performance, minimize downtime, and extend the service life of the appliance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
