DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM is a refrigerator water tank assembly supplied as an original equipment part for compatible Samsung refrigeration units. The component is a molded reservoir and associated fittings that store and route potable water for the appliance’s dispenser and ice-making subsystems; the assembly typically includes inlet/outlet ports, mounting bosses, and seals or grommets necessary for integration into the cabinet. As an OEM-designated assembly, it is indeed intended to replace the factory-fitted tank with parts that match original form, fit and interface points.
Inside the appliance,the water tank functions as the intermediate storage and distribution node between the external water supply and downstream devices such as the water dispenser and ice maker. It interacts directly with the water inlet valve and solenoid, interconnecting tubing, water filters, and the refrigerator control electronics that command fill cycles and monitor level or flow sensors. Proper sealing, correct orientation, and secure tubing connections are essential because the tank must maintain water pressure and prevent leaks while operating in the refrigerator’s thermal surroundings where partial freezing or condensation can occur.
in this article readers will find a technical examination of the assembly’s function and typical mounting locations, guidance on model compatibility and how to verify the DA97-17395B is the correct replacement, common failure symptoms (for example leaks, no or intermittent dispensing, slow fill or ice-maker filling problems, and cracking from thermal stress), diagnostic approaches to isolate tank-related faults, and practical replacement considerations such as matching connector types and seals, handling precautions (power and water isolation), and verification checks after installation. The focus is on providing technicians, engineers, and informed appliance owners with the practical context needed to assess, diagnose, and plan a safe replacement while ensuring system interfaces are correctly managed.
Table of Contents
- Function and role of the Refrigerator Water Tank Assembly in Water Delivery and pressure Regulation
- How the DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM Operates Within the Refrigerator Water and Ice-Making Systems
- Common Failure Symptoms and Quantitative Diagnostic Indicators for Tank water Assemblies
- Replacement Considerations, Model Compatibility, Installation Steps and Troubleshooting Diagnostics
- Q&A
- Final Thoughts
Function and Role of the Refrigerator Water Tank Assembly in Water Delivery and Pressure Regulation
The DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM is a molded refrigerator water reservoir assembly that provides a small, pressurized buffer between the household water inlet and the dispenser/ice-making circuits. Mounted downstream of the inlet solenoid, the assembly’s internal volume and flow path dampen inlet pressure spikes and maintain steady outlet flow during dispenser activation. In practical installations this assembly aligns with OEM port locations, mounting bosses, and connector orientations so technicians can replace a failing unit without re-routing lines or modifying brackets; always verify the part number and port layout against the service schematic for the specific Samsung model before installation.
Functionally,the tank assembly regulates delivery by combining an internal buffer volume with flow-restricting geometry or an integrated check valve to prevent backflow and reduce transient water-hammer when valves open and close. Typical behavior includes providing an immediate short-duration flow reserve (improving dispenser responsiveness) and smoothing pressure variations that would or else cause sputtering or inconsistent ice machine fills. Common service observations that indicate tank-related issues include low steady flow despite correct inlet pressure, intermittent air in the dispenser stream, and audible inlet valve cycling that does not correspond to expected fill times. for field replacement and troubleshooting, isolate the water supply, depressurize the line, inspect inlet screens and valve seating, and confirm that outlet fittings and sensors are correctly aligned after installing the replacement assembly.
- Primary functions: short-term flow buffering, pressure dampening, and backflow prevention.
- Interfaces: inlet solenoid, dispenser tubing, ice maker feed, mounting brackets and sensor/float connectors.
- Common failure modes: cracked reservoir, clogged inlet screen, failed check valve or internal baffle degradation.
| Item | Description |
|---|---|
| Part number | DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM |
| Function | Reservoir and pressure-regulating buffer for dispenser and ice maker feeds |
| Interfaces | Water inlet valve, dispenser tubing, ice maker feed line, mounting points |
| Typical symptoms | Low or inconsistent flow, air in stream, excessive inlet valve cycling |
How the DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM Operates Within the refrigerator Water and Ice-Making Systems
DA97-17395B Samsung assembly TANK WATER REF;AW3 F/L OEM is a molded internal water reservoir assembly that stores and routes potable water between the refrigerator’s inlet valve, the door dispenser, and the ice-maker fill circuit. In operation it provides a short-term buffer to dampen pressure spikes from the household supply and to supply a measured volume of water during ice-maker fill cycles and dispenser requests. the assembly typically incorporates molded ports,mounting tabs,and sealing interfaces that link to the inlet tubing and solenoid valves; these interfaces determine fit and function and are the primary compatibility points when replacing the unit.
During a dispense or harvest/fill sequence the refrigerator’s inlet valve opens to feed the reservoir,then a downstream solenoid or the ice-maker’s fill valve meters water from the reservoir into the ice tray. Proper operation depends on intact seals, unobstructed ports, and correct orientation within the cabinet so gravity and tubing routing produce reliable flow. Technicians should verify the condition of push-fit connectors or hose clamps, check for cracks or sediment that can restrict flow, and confirm that mounting points align to avoid stress on tubing. Replacing the assembly with the OEM DA97-17395B ensures matching port geometry and mounting locations, reducing fitment issues and the need to modify existing tubing.
- Primary functions: short-term storage, pressure damping, and controlled delivery to dispenser and ice maker
- Interfaces: molded ports for inlet/outlet, mounting tabs, and sealing surfaces (model-dependent)
- Common failure symptoms: reduced dispense flow, intermittent ice fill failures, visible leaks at connections
- Service tips: inspect O‑rings, clean inlet screens, and pressure-test fittings after replacement
| Item | Description |
|---|---|
| Function | Reservoir and routing component between inlet valve, dispenser, and ice-maker fill circuit |
| Connections | Push-fit or barbed hose ports; exact size and style are model-dependent |
| Material | molded plastic construction with internal baffles to stabilize flow |
| Location | Mounted inside the refrigerator cabinet near the water inlet and ice-maker assembly |
Common Failure Symptoms and Quantitative Diagnostic Indicators for Tank Water Assemblies
DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM is the molded reservoir and associated valve/sensor subassembly that controls water delivery to the dispenser and ice-making systems. When functioning correctly the assembly maintains a small head of water, seals against leakage, and presents expected electrical and hydraulic characteristics to the refrigerator control system. Failures of this assembly typically affect flow rate, containment (leaks), and the signals to the control board; these failures can be isolated with basic hydraulic and electrical measurements rather than by visual inspection alone. Technicians should consider compatibility of replacement units with connector pinouts and valve coil ratings before installation to ensure correct signaling and mechanical fit.
- Low or no flow: measured dispenser flow below typical service thresholds (see reference table) or flow that varies significantly between dispensing attempts.
- leaks or seepage: continuous drip from tank seams or fittings exceeding small accumulation thresholds over hours.
- Intermittent operation or noise: valves that click repeatedly, or intermittent solenoid energizing without water delivery, indicating valve coil, armature, or debris issues.
- Electrical faults: open or shorted solenoid coil, or sensors/float switches that do not change continuity when actuated.
| Item | Description |
|---|---|
| Nominal dispenser flow | Typically ≥300 ml/min at normal household pressure; sustained readings <200-300 ml/min suggest restriction or partial valve failure. |
| Leak threshold | Visible seepage accumulating >10 ml/hour at fittings or seams indicates failed seal or cracked tank. |
| Valve coil resistance | Coil continuity expected; open circuit indicates failure. Typical coil resistance may be in the range of 50-200 Ω-refer to OEM spec for exact value. |
| Operating water pressure | System feed pressures below ~20 psi often produce weak flow; normal household range is roughly 20-80 psi. |
Apply these quantitative checks as part of a stepwise diagnostic: measure static inlet pressure, verify dispenser flow with a container and timed measurement, and record electrical values at the solenoid and any float/sensor terminals. For example, if inlet pressure is 40 psi but dispenser delivers 150 ml in 30 seconds (≈300 ml/min expected), the restriction is highly likely internal to the DA97-17395B assembly or an upstream filter; if the coil shows open circuit while the valve never actuates, replace the valve or the entire assembly. Always compare measured values to the refrigerator’s service manual and OEM specifications before deciding on replacement to avoid replacing compatible parts unnecessarily.
Replacement Considerations,Model Compatibility,Installation Steps and Troubleshooting Diagnostics
DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM is the molded reservoir that stores and routes potable water within the refrigerator chassis for the dispenser and icemaker. The assembly integrates inlet and outlet hose connections, mounting flanges, and a sensor/float interface in a single OEM-molded component; these features control flow, prevent siphoning, and provide a repeatable reference for fill-level detection. When evaluating replacement compatibility, compare mounting-tab spacing, hose barb diameters, and the location and pinout of any electrical connector or sensor mounting boss against the service manual for the target refrigerator model. Mechanical fit and sealing surfaces are the most common causes of poor replacement outcomes - a correctly matched OEM replacement eliminates minor geometry differences that can cause leaks, misrouting of tubing, or interference with adjacent components like evaporator panels or brackets.
Installers should follow a controlled procedure and use diagnostic checks after replacement to confirm correct behavior. Isolate water and electrical supply, relieve pressure and drain residual water, then verify that gaskets and clamps are new or undamaged and that hose runs are free of kinks; after reassembly, perform a static leak test and then a dynamic fill test while monitoring the fill-level sensor and dispenser output. For troubleshooting, correlate symptoms to component function: persistent leaks point to sealing or alignment errors, absent dispenser flow with a full tank indicates an inlet valve or outlet blockage, and erratic fill-level readings suggest a damaged float/sensor or wiring fault. Practical example: if the icemaker fails to fill but the tank fills normally, measure continuity and voltage at the tank sensor connector and inspect the inlet valve timing rather than immediately replacing the reservoir.
- key post-install checks: leak test (static 5-10 min), actuator/valve voltage during fill, sensor continuity or resistance, and hose clamp torque/position.
| Item | Description |
|---|---|
| Part | DA97-17395B Samsung Assembly TANK WATER REF;AW3 F/L OEM – OEM molded reservoir assembly |
| Mounting | Match tab spacing and orientation to chassis; improper alignment causes leaks or interference |
| Connections | Hose barb diameters and connector pinout must match factory harness and tubing sizes |
| Common symptom | leaks at seals, no dispenser output, or inconsistent fill-level readings |
Q&A
what is the DA97-17395B (Assembly, Tank, Water) and what does it do?
The DA97-17395B is an OEM water reservoir/tank assembly used in certain Samsung refrigerators. It stores a small volume of potable water inside the cabinet to feed the dispenser and/or ice maker. The tank helps maintain steady water pressure at the dispenser and gives the system a small buffer between the household supply and the dispenser/ice maker valves.
How do I know if my refrigerator needs this specific tank (DA97-17395B)?
Check the part number on your existing tank (if accessible) or look up parts for your refrigerator model number (printed on a label inside the fridge or on the cabinet). DA97-17395B is an OEM part number - if your model lists that part in the Samsung parts diagram or the tank label matches, it’s the correct replacement. If unsure, provide your refrigerator model number to a Samsung parts dealer or authorized service centre to confirm compatibility.
What are common symptoms of a failing or leaking water tank assembly?
Symptoms include visible water pooling under/behind the fridge, reduced or intermittent water flow from the dispenser, water dripping from inside the cabinet, and in certain specific cases, dispenser air sputtering caused by a loss of reservoir pressure. If the tank cracks or the fittings fail you may also get leaks when the dispenser or ice maker runs.
can I replace the DA97-17395B myself and what precautions should I take?
Yes, a competent DIYer or technician can replace it. Precautions: unplug the refrigerator and shut off the house water supply, place towels or a shallow pan to catch water, and depressurize the lines by dispensing water after shutting off supply. Use appropriate hand tools (screwdriver, nut driver, pliers) and avoid forcing plastic fittings.Be careful of sharp sheet metal inside the cabinet and replace any O‑rings or seals when reassembling. If you’re unsure, hire a qualified appliance technician.
What are the basic steps to replace the water tank assembly?
Typical steps: 1) Unplug the fridge and turn off the water supply. 2) Remove kickplate/grille and any interior panels necessary to access the tank. 3) place towels and catch bowls under the area. 4) Disconnect water lines (note type of rapid-connect or push-fit connector and depress the release collar), electrical connectors, and mounting screws. 5) Remove the old tank and install the new tank in reverse order, ensuring O‑rings/seals are seated and lines are fully inserted. 6) Turn on the water, check for leaks, plug in the refrigerator, and purge air by dispensing several glasses of water.
After installing a new tank the dispenser still has low flow – what should I check?
Check for kinks or pinches in the inlet tubing, a clogged or frozen filter (replace if needed), the water inlet valve (may be failing or clogged with debris), and any inline filters or screens. Also verify that quick‑connect fittings are fully seated and not leaking air; trapped air will reduce flow until purged by dispensing several liters. If your model uses an internal pump or heater to prevent freezing, ensure those components are functional.
Are there differences between OEM (DA97-17395B) and aftermarket tanks, and should I buy OEM?
OEM parts are manufactured or approved by Samsung and are guaranteed to match original fit, materials, and function. Aftermarket tanks can be less expensive but may vary in fit,plastic quality,or connector placement; they can require modifications or result in leaks if not exact. For best reliability and warranty coverage, many technicians recommend using the OEM DA97-17395B.
How do I check the tank for leaks or internal damage before installing?
Visually inspect the tank for hairline cracks, especially around molded seams and connector ports. Check O‑rings and seals for nicks, hardening, or deformation. You can bench-test the tank by connecting the supply line, submerging any suspect connections in a shallow pan, and briefly pressurizing the tank (turn on water for a few seconds) while watching for drips. Never exceed normal household water pressure when testing.
Final Thoughts
The DA97-17395B samsung Assembly TANK WATER REF;AW3 F/L OEM serves as an integral component in the water management and delivery system of compatible Samsung refrigeration units. By providing a properly fitted, manufacturer-specified reservoir and connections for water distribution, this assembly helps maintain reliable dispensing, supports ice-making functions, and reduces the risk of leaks or contamination when installed and maintained according to specifications.As an OEM part,it is indeed designed to meet original performance and safety standards for fit,materials,and operation.
Accurate diagnosis and timely replacement of a failing tank assembly are essential to preserve appliance function and prevent secondary damage. Technicians and owners should confirm symptoms, verify compatibility, and follow manufacturer procedures when evaluating the unit; when replacement is required, using the correct OEM DA97-17395B part and adhering to installation guidelines will help ensure long-term reliability and safety. Proper diagnosis, professional installation, and routine maintenance protect both appliance performance and user peace of mind.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
