DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM
DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM is an ice-maker assembly designed for use in compatible Samsung freezer compartments and is specified for 120 V operation. This module is a modular refrigeration subsystem that typically integrates the ice mold, drive motor and gear train, water inlet valve or its mounting interface, basic control electronics and associated sensors or thermostats; it is supplied as an OEM replacement part intended to fit designated Samsung models without major modification.
Within the appliance the assembly’s primary role is to produce,harvest and dispense ice on a controlled cycle,and it interfaces with the refrigerator’s main control board,water supply and fill valve,temperature sensors,and,where present,dispenser and door-switch circuits. Proper operation depends on coordinated signals (timing and power) from the refrigerator controller, correct water pressure and supply, and accurate temperature feedback from the freezer compartment; faults in any of those interacting systems can affect the ice assembly’s performance or produce secondary symptoms such as leakage, incomplete fills, or mechanical jams.
In this article readers will find a technical overview of the assembly’s functional elements, guidance on model compatibility and part-number verification, common failure symptoms to recognize (for example no ice production, continuous water flow, noisy or stalled ejector motor, or improper ice size), step-by-step diagnostic checks a technician can perform (electrical checks, continuity and voltage tests, mechanical inspection and water-line verification), and practical considerations for safe removal and replacement including wiring, mounting, and water shutoff. Emphasis is placed on objective troubleshooting procedures and fitment/compatibility issues rather than promotional claims, so technicians, engineers and appliance owners can make informed repair and replacement decisions.
Table of Contents
- Function and role of the DA82-02701A Ice Maker Assembly in Samsung Refrigeration systems
- How the DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM Works Inside the Appliance
- Common Failure Symptoms and Diagnostic Indicators for DA82-02701A Ice Maker Assemblies
- Compatibility, Replacement Considerations and troubleshooting Procedures for DA82-02701A / DA92-00384R 120V OEM in Samsung Models
- Q&A
- Future Outlook
Function and Role of the DA82-02701A Ice maker Assembly in Samsung Refrigeration Systems
The DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM serves as the electromechanical subsystem that produces, releases, and meters ice within compatible samsung refrigeration units. Physically it integrates a molded ice tray, drive motor with ejector mechanism, a thermostatic/position sensor (or cam switch), a small heater for the harvest cycle, and the water-fill cup and inlet interface. Electrically the assembly runs on the refrigerator’s internal 120V supply and receives timing and actuator commands from the main control board; the control board energizes the fill solenoid and motor and reads the ice-arm or cam sensor to sequence fill, freeze, harvest, and rest intervals. In practical repairs, technicians replace this assembly (rather than individual components) when motor failure, heater open circuits, or worn ejector parts produce repeated harvest or fill faults in models that accept the DA92 series interface.
- primary functions: mold fill metering, freeze-hold timing, harvest heating, cube ejection, and bin-level sensing.
- Common failure indicators: no ice production, partial/soft cubes, continuous water fill, or noisy drive motor during harvest.
- Compatibility checks: verify plug harness pins, mounting plate alignment, and 120V supply compatibility before installation.
| Item | Description |
|---|---|
| Voltage | 120V AC operational rating matching OEM refrigerator internal circuits |
| Core components | Motor, ejector/arm, heater element, position sensor/cam, water fill cup |
| Typical service actions | Verify control signals, test heater and motor continuity, inspect cam/sensor alignment, replace assembly when multiple subsystems fail |
How the DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM Works Inside the Appliance
The DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM is a self-contained ice-maker module designed to perform the complete ice-production cycle inside compatible Samsung freezers. The assembly houses the ice mold, ejector motor and gears, harvest heater and thermostat/thermistor, and the water-fill interface; it runs off a standard 120V supply and is actuated by timed control signals from the refrigerator’s main board or an integrated ice-maker switch. Functionally, the module fills the mold, allows the water to freeze to a defined temperature, activates a heater and mechanical ejector to release cubes, and then refills the mold-failures in any of these subcomponents produce distinct symptoms such as no-fill, no-eject, continuous run, or leaking at the fill connection.
- Key components: ice mold, motor/gearbox, harvest heater + thermostat, water inlet interface, and electrical harness.
- Electrical behavior: receives 120V power pulses for motor/heater; control timing is typically provided by the main control board or an internal switch.
- Common failure symptoms: no water fill (valve or inlet solenoid), ice not ejecting (motor/gears), continuous harvest (thermostat/thermistor fault), or ice bridge formation (mechanical misalignment).
- Practical checks: verify harness voltage during a cycle, measure heater/thermostat continuity at low temperatures, inspect the ejector motor resistance and mechanical linkage for binding.
| Item | Description |
|---|---|
| Voltage | 120V mains for motor and heater circuits; control signals are low-voltage timing inputs from the main board. |
| Primary functions | Fill, freeze, harvest (heater + ejector), and refill-complete cycle managed by the assembly and control inputs. |
| Diagnostics | Measure voltage at the ice-maker connector during the cycle, check heater/thermostat resistance, and inspect motor for mechanical binding or stripped gears. |
When replacing or troubleshooting this assembly, confirm mechanical alignment of the fill tube and mold, ensure the water inlet valve and supply pressure are within specifications, and verify connector pinouts against the refrigerator wiring diagram before applying power. Technicians typically isolate faults by observing the ice-maker during a manual harvest command: no voltage to the motor suggests a control-board or harness issue, voltage present but no motor movement indicates a motor/gearbox fault, and heater voltage present with no harvest release points toward mechanical binding or thermostat failure.
Common Failure Symptoms and diagnostic Indicators for DA82-02701A Ice Maker Assemblies
The DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM is a modular ice maker assembly that integrates the ice mold, motor-driven ejector, harvest heater, thermistor/bi-metal thermostat, and the fill-level/lever switch. In operation the assembly controls the water fill and freeze/harvest sequence under command of the refrigerator control board; the 120V harvest heater and motor provide the thermal and mechanical actions necessary to release cubes. Compatibility is generally limited to Samsung models that accept the DA92-series mount and 120V harness; replacing a failed assembly with this OEM unit preserves original connectors, mounting points, and the expected electrical interface for reliable signaling between the ice maker and the main control board.
- No ice production - possible causes: open heater, failed motor, or lack of water fill (check inlet valve and fill tubing).
- Small or soft cubes - frequently enough caused by insufficient freeze time due to thermostat/thermistor failure or a degraded evaporator performance upstream.
- Continuous water flow into the mold – intermittent or stuck fill-level switch or failed control timing leading to overfill.
- Ice stuck in mold or incomplete harvest – heater not reaching temperature or ejector motor torque insufficient.
- Audible clicking or abnormal motor noise - worn motor gears or mechanical obstruction in the ejector assembly.
| Item | Description |
|---|---|
| Key specs | DA82-02701A assembly; 120V heater; direct-fit DA92-series mounting |
Diagnostic indicators should be correlated across electrical, thermal, and mechanical checks: verify continuity of the harvest heater and motor circuits, confirm the thermistor/bi-metal closes at the expected cold threshold, and observe the ice maker through a full fill/freeze/harvest cycle to identify at which stage failure occurs.For example, if the unit attempts a harvest but cubes remain adhered, measure heater continuity and inspect heater adhesion to the mold; if the motor turns but the ejector does not move freely, disassemble to inspect gears and cams for wear. Documenting observed symptoms alongside control board error codes and basic voltage/continuity readings will pinpoint whether the assembly itself is defective or if upstream components (water inlet valve, temperature control, or board outputs) are the root cause.
Compatibility, Replacement Considerations and Troubleshooting Procedures for DA82-02701A / DA92-00384R 120V OEM in Samsung Models
The DA82-02701A Samsung A/S Assembly ICE;FS DA92 00384R 120V OEM is an OEM ice-maker module that combines the mold, ejector/motor, heater elements, and the electrical harness designed for 120 VAC freezer circuits. It executes fill, freeze, and harvest sequences under command from the refrigerator control board; functionally the assembly provides the mechanical drive for cube ejection, the molded heater or heater traces for harvest cycles, and sensors or thermostats that signal cycle completion. Revisions between DA82-02701A and DA92-00384R are generally interchangeable electrically when the connector pinout and control signals match, but physical mounting brackets, harness length, and minor sensor placements can differ between model years so verification of fit and connector compatibility is required before installation.
Replacement and troubleshooting focus on isolating electrical, mechanical, and water-supply faults. Perform a controlled diagnostic: verify presence of 120 VAC at the assembly connector during a commanded harvest, measure resistance of the heater and motor windings, verify continuity of any mold thermostat or thermistor, and confirm water inlet valve operation and adequate line pressure for proper fill. After replacement, force a manual fill/harvest cycle from the service menu or by applying the appropriate supply voltage to observe fill volume, harvest timing, and complete ejection; if symptoms persist, compare connector pin voltages and waveform timing against the original assembly to determine whether the control board or wiring harness is at fault rather than the ice assembly itself.
- No ice production – check water supply pressure, inlet valve actuation, and fuse/line voltage to the assembly.
- Hollow or small cubes – inspect fill duration and water inlet flow; verify fill cup alignment and supply restrictions.
- Continuous harvest or failure to eject - measure heater/motor continuity and check for ice jams or stuck ejector blades.
- Intermittent operation – inspect connector pins for corrosion and confirm control board outputs during diagnostic cycles.
| Item | Description |
|---|---|
| Voltage | 120 VAC supply for motor/heater circuits; confirm during harvest cycle with a meter. |
| Connectors | Match pinout and locking tab; harness length and orientation may differ between part revisions. |
| Common failures | Burned heater, seized ejector motor, faulty mold thermostat/thermistor, or clogged inlet valve/low water pressure. |
| Compatibility notes | DA82-02701A and DA92-00384R are frequently enough functionally equivalent OEM units, but verify mechanical fit and control-board signaling before substituting. |
Q&A
What is the DA82-02701A / DA92-00384R ice maker assembly and what does “120V OEM” mean?
The DA82-02701A (also referenced as DA92-00384R) is an original-equipment-manufacturer (OEM) ice maker assembly used in manny Samsung refrigerators. It is the complete ice-making unit (motor, harvest heater/thermostat, fill cup, and mounting bracket) and is designed to operate on standard household AC voltage (120 volts). “OEM” indicates it is indeed a genuine samsung part, not an aftermarket repro.
How do I know if this part is compatible with my Samsung refrigerator?
Verify compatibility by checking your refrigerator’s model number (usually on a sticker inside the fridge or on the door frame) and cross-referencing it with the part number in the Samsung parts database or with the supplier. Many Samsung French-door, side-by-side and bottom-freezer models use these part numbers, but always confirm before purchase to avoid fitment or connector differences.
My ice maker stopped making ice – how can I tell if the ice maker assembly is the problem?
Start with basic checks: ensure the freezer temperature is in the correct range (about 0°F / -18°C), the water supply is turned on, the water inlet valve and line are not blocked or frozen, and the ice bin is correctly seated. If those are OK, check for power at the ice maker connector (with the fridge plugged in and calling for ice) – you should see ~120 VAC at the connector during the fill/harvest cycle.If there is power but no motor/heater action, or the module shows obvious damage, the ice maker assembly is likely faulty and should be replaced.
What are safe, recommended steps to replace this ice maker assembly?
Turn off power to the refrigerator (unplug or switch off breaker) and shut off the water supply. Remove the ice bin and any interior panels blocking access. Disconnect the electrical connector and the water fill tube (some models have a slip-on tube or a fast-disconnect). remove screws securing the assembly and pull out the old unit. Install the new assembly in reverse order, reconnect the fill tube and electrical connector, secure mounting screws, restore water and power, then run a test/harvest cycle. Use basic hand tools (screwdriver, nut driver) and a towel for water drips. Always follow any model-specific instructions from Samsung.
How can I test the ice maker assembly without installing a replacement part?
You can test components with a multimeter: check for continuity on the motor and thermostat/heater circuits, and check for ~120 VAC at the ice maker connector while the unit is in a cycle. To force a harvest/test cycle some Samsung units have a small test button on the module – pressing and holding it (typically 3-5 seconds) initiates a harvest on models with that feature. if you’re not cozy working around live voltage, have a qualified technician perform these tests.
My ice maker hums but won’t fill with water – could this part be at fault?
If the motor hums, the ice maker assembly might potentially be trying to cycle but not filling. Common causes include a frozen or kinked fill tube, a faulty water inlet valve (separate part), or a misaligned fill cup. Verify water pressure and the inlet valve operation first. If the inlet valve is confirmed working and the fill tube is clear, a defective fill mechanism inside the ice maker assembly or a failed solenoid inside the module could be the cause and the assembly should be replaced.
Are there common failure modes for this assembly and how long should it last?
Typical failures include a failed motor, broken ejector or auger components, failed harvest heater or thermostat (especially if ice is not ejecting or cubes stick to the mold), and cracked fill cups or broken mounts. Lifespan varies by usage and water quality, but OEM units often last many years. hard water can accelerate wear; using a water filter and periodic cleaning helps extend life.
After replacing the ice maker, how do I initialize or test that it is working properly?
After installation, restore power and water, then either press the test/reset button (if present) or allow the unit to go through its normal cycle. You should hear the motor and occasional water fill noises. Expect the first batch to take several hours (frequently enough 6-12 hours) to form cubes. If your model has a manual test mode, consult the refrigerator’s tech sheet or user manual for the exact button sequence. Check for proper fill volume, ejection of ice, and no leaks at the fill tube connection.
Future Outlook
The DA82-02701A (Samsung A/S Assembly ICE;FS) and its OEM counterpart DA92-00384R 120V are integral components in compatible Samsung refrigeration systems, responsible for reliable ice production, electrical interface and coordination with the appliance’s control systems. As factory-designed parts, they are engineered to meet the appliance’s voltage and performance specifications, contributing to consistent operation, energy efficiency and overall appliance longevity when installed correctly.
Accurate diagnosis is essential to determine whether the assembly is the root cause of an ice-making or electrical issue, which helps avoid unnecessary replacements and additional downtime. When replacement is necessary, sourcing the correct OEM part number and following manufacturer-recommended installation practices-or engaging qualified service personnel-helps ensure safe, effective restoration of function and reduces the risk of collateral damage to other components.
recognizing the role of the DA82-02701A/DA92-00384R assembly and emphasizing proper diagnosis and appropriate replacement preserves appliance performance and reliability. Timely, professional intervention and the use of correct OEM parts support long-term operation and provide the best outcome for equipment owners and service providers alike.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
