DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM
DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM is an ice-maker assembly used in Samsung refrigerator models and serves as the integrated mechanical and electrical unit responsible for producing and harvesting ice.The assembly typically includes the ice mold, ejector mechanism, drive motor or stepper, water-fill interface, thermostat/thermistor or temperature sensing element, and a connector harness that mates with the appliance control board; the DA94 02275P designation refers to associated connector or subassembly details for OEM replacement identification.
Within the appliance, this ice assembly interfaces with the refrigerator control board, water inlet valve, and user interfaces or dispenser controls to coordinate fill cycles, freeze timing, and ejection of ice into the storage bin.It relies on temperature feedback to determine freeze completion, a timed or sensor-driven ejection sequence to release cubes, and sealed water connections to prevent leaks; failures or miscommunication in any of these subsystems (electrical harness, sensors, motor, or water supply) will directly affect ice production and can cause symptoms such as no ice, undersized cubes, continuous motor operation, or leaking.
This article will explain the assembly’s functional components and operating sequence, outline model compatibility and how to verify correct part selection, describe common failure symptoms and diagnostic checks a technician or informed appliance owner can perform, and present practical troubleshooting and replacement considerations including inspection of electrical connections, water inlet integrity, sensor verification, mechanical wear points, and post-replacement testing. As with any service procedure, disconnecting power and water before inspection or replacement is recommended and wiring diagrams and model-specific service manuals should be consulted for exact voltages and pinouts.
Table of Contents
- Functional Role and System Integration of the ICE Assembly within Samsung Refrigeration
- How the DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM Operates: Electrical,Mechanical,and Control Interfaces
- diagnostic Indicators and Common Failure Symptoms of the Ice Assembly
- Replacement Considerations,Model Compatibility,Installation Procedures,and Troubleshooting
- Q&A
- To Conclude
Functional Role and System Integration of the ICE Assembly within Samsung Refrigeration
The DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM is an OEM ice-maker assembly that provides the mechanical and sensing functions required to form,harvest and deliver ice within compatible samsung freezer compartments. The assembly contains a motor-driven ejector, a heater for the harvest cycle, a water-fill detection element (mechanical switch or sensor), and a thermistor or thermostat for temperature feedback. Physically it mounts to the freezer liner and interfaces with the refrigerator’s electronics through a multi-pin connector; the main control board supplies switched power and a harvest command while the assembly controls water fill timing and the mechanical ejection of ice. Technicians should verify connector pinout and mounting points during replacement because variations in connector arrangement or actuator type affect compatibility even among parts with similar part numbers.
- Primary functions: ice formation timing, water fill control, harvest initiation and ice ejection.
- Sensors: temperature feedback (thermistor/thermostat) and a fill/level detection switch used to prevent overfill.
- Actuators: low-voltage motor for the ejector and a short-duration heater to release ice from the mold.
- Interface considerations: multi-pin connector for power and control lines, and mechanical mounting that must match the freezer cavity.
| Item | Description |
|---|---|
| Interface | multi-pin connector carrying switched power and a harvest/advance signal from the refrigerator control board. |
| Functions | Motor-driven ejector, harvest heater, fill detect switch, and temperature sensing element for cycle timing. |
| Mounting | plastic housing with specific screw bosses and alignment tabs; requires correct orientation for water trough and drain alignment. |
| Replacement tip | Compare connector pin layout and sensor type to the original assembly-visual match and part number confirmation reduce installation errors. |
In-system behavior is event-driven: the refrigerator control board schedules a freeze period based on the thermistor reading, then energizes the fill valve and monitors the fill sensor; after freezing, the board issues a harvest command and the ice maker applies heat and turns the motor to eject cubes. Common failure modes include open motor windings, failed heater elements, intermittent fill switches, or corroded connector pins; diagnostic checks include continuity of motor and heater circuits, resistance trend of the temperature sensor, and observation of control signals at the connector during a manual harvest cycle. For practical servicing, reproduce the harvest cycle manually (where supported by the control board) to observe mechanical operation, and if the assembly fails mechanical or electrical tests, replace with the correct OEM assembly or a confirmed compatible equivalent to ensure proper integration with the refrigerator’s control logic and water system.
How the DA82-02668A samsung A/S Assembly ICE;DA94 02275P CD 120 OEM Operates: Electrical, Mechanical, and Control interfaces
The DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM is an integrated ice-maker assembly that combines mechanical actuation, heating elements for harvest, fill control, and sensing into a single service-replaceable unit. mechanically, the assembly uses a low-speed gear motor and cam to sequence the ice cycle: that cam actuates the ejector fingers and a cam-operated switch or microswitch to time the water-fill and harvest events. Electrically, the unit expects discrete power and control lines from the refrigerator main board – typically a line-level heating circuit for the harvest heater and low-voltage motor and valve control signals – and a multi-pin harness that carries motor power, heater feed, fill-valve command, and a temperature or presence sensor feedback to the control board.
Control behavior is governed by the refrigerator’s logic board which supplies timed drive voltages and reads the ice sensor or thermostat to decide when to start and stop the motor and heater. Compatibility depends on matching the harness pinout,mounting tabs,and sensor type; swapping the DA82-02668A/DA94-02275P unit into a different model requires confirming connector pin assignments and nominal voltages. practical troubleshooting examples: a unit that fills continuously typically has a failed sensor or stuck valve, a unit that never ejects may have a burned motor winding or open cam switch, and a unit that fails to harvest can show an open heater circuit.
- Typical checks: verify harness continuity,measure motor/heater supply under command,and confirm sensor resistance at refrigerator temperatures.
| Item | Description |
|---|---|
| Mounting/Harness | Multi-pin connector with model-specific pinout; mounts to inner freezer liner with plastic brackets. |
| Motor/Cam | Low-speed gearmotor driving a cam that sequences fill,eject,and switches. |
| Heater | Harvest heater powered by the refrigerator’s line-level circuit to slightly warm the mold for release. |
| Sensor | Thermal or optical presence sensor that signals ice ready/filled conditions to control board. |
Diagnostic Indicators and Common Failure Symptoms of the Ice Assembly
The ice assembly identified as DA82-02668A Samsung A/S assembly ICE;DA94 02275P CD 120 OEM is a modular replacement that integrates the ice mold, ejector (motor/gear train), harvest heater or thermostat, fill inlet and mounting bracket into a single serviceable unit.In normal operation the module controls a fill cycle (open the water inlet, dose the mold), a freeze interval, and a harvest cycle (apply heat or activate a thermistor/bi-metal to release cubes while the ejector clears them into the bin). Technicians should treat this assembly as a mechanical/electrical subsystem: failures commonly trace to the motor/ejector, the harvest heater or sensor, the water inlet valve or fill tube freeze, or to the control signals from the refrigerator main board. When replacing this assembly, confirm compatibility with the service manual and match the DA82-02668A / DA94-02275P references to avoid mismatched connector pinouts or harvest heater types.
Typical diagnostic indicators show specific symptoms that narrow the fault to a subsystem. For example, a running motor with no cubes released suggests a stuck ejector or stripped gears, while cubes that are small or hollow suggest under-fill or low water pressure; continuous refilling or overflow points to a stuck inlet valve or faulty level detection. Use systematic checks – inspect the mold for icebridges in the fill tube, verify water flow at the valve, manually initiate a harvest cycle and observe heater behavior, and measure continuity of the motor and heater against service specifications – before replacing the entire assembly. Record observed behavior and any refrigerator error codes, and compare them to the assembly’s pinout and expected signals to determine whether the fault is in the assembly itself or in upstream controls.
- No ice production but motor cycles: likely water supply issue, inlet valve, or frozen fill tube.
- Motor runs continuously or hums without ejecting cubes: possible seized ejector, stripped gears, or motor failure.
- Ice cubes misshapen, small, or hollow: under-fill caused by low pressure, partially blocked inlet, or short freeze time.
- Intermittent harvest or no harvest: failed heater/thermostat/thermistor or missing control signal from main board.
- Water leaking into bin or onto floor: defective inlet valve or cracked fill tubing/assembly seal.
| Item | Description |
|---|---|
| Symptom | No ice, motor sounds, no fill – check water valve, frozen fill tube, and inlet pressure |
| Symptom | Ice not ejected or ejector slips – inspect ejector gears, motor continuity, and harvest mechanism |
Replacement Considerations, Model Compatibility, Installation Procedures, and Troubleshooting
The DA82-02668A Samsung A/S Assembly ICE;DA94 02275P CD 120 OEM is a refrigerator ice-making assembly that combines the mechanical ejector, fill valve interface, and sensing elements into a single replaceable unit. This assembly transmits simple on/off and timed control signals to the main PCB through a multi-pin connector and mounts to the freezer liner using a defined hole pattern; mismatches in connector pinout, mounting geometry, or sensor placement are the most common causes of incompatibility. Technicians should verify the mating harness, confirm that the thermistor or switch locations align with the cabinet cutouts, and compare OEM cross-reference numbers before installation to avoid electrical or mechanical mismatches that can cause intermittent operation or flooding.
- Basic installation checklist: disconnect mains and water, document connector orientation, remove retaining screws, transfer any reusable brackets, seat the unit fully, reconnect harness and water, then run a single harvest cycle and inspect for leaks.
when diagnosing installation or operational faults, use a multimeter to verify continuity across the motor and heater circuits, check coil resistance on the fill valve, and observe the control signals from the main board during a harvest/test mode; shorted heaters, open sensors, or incorrect drive voltages are typical failure modes. Common field symptoms and pragmatic checks include: no ice produced (confirm valve opens and water pressure present), continuous fill (inspect the float/switch and valve coil), and noisy or failed ejector (measure motor resistance and check for mechanical obstruction). replace the assembly only after isolating the fault to the module itself or after confirming replacement part compatibility with the refrigerator model.
| Item | Description |
|---|---|
| Connector/Pinout | Verify mating harness pins and voltages match the main PCB before installation |
Q&A
What exactly is the DA82-02668A / DA94-02275P CD 120 OEM ice assembly?
These part numbers refer to a Samsung OEM ice maker assembly (A/S Assembly ICE). It is the complete ice-making module that mounts inside the freezer: it contains the fill valve interface, ice mold, motor/ejector, harvest heater (when used), electrical connectors and mounting points.”OEM” means it is an original Samsung replacement part, intended to match the factory unit in form, fit and function.
How do I know if this ice maker assembly is compatible with my Samsung refrigerator?
Check the refrigerator model number (usually on a sticker inside the fresh food compartment or behind a freezer panel) and compare it to the part compatibility list from Samsung or the parts distributor. Cross-reference DA82-02668A or DA94-02275P with your exact fridge model and serial number – manny online parts sites and Samsung service manuals list compatible models. If in doubt, provide your fridge model to the seller or Samsung service for confirmation before buying.
What tools and safety steps are required to replace the ice maker?
Safety: disconnect power to the refrigerator and shut off the water supply to the appliance before beginning. Tools: Phillips and flathead screwdrivers, nut driver or socket set (usually 1/4″ or 5/16″), needle-nose pliers, towel to catch water, and optionally a multimeter for testing. Work in a dry area and follow any ESD precautions if handling electronic connectors. Keep small screws and clips organized for reassembly.
Can I install this ice maker myself? What are the basic installation steps?
Yes, a competent DIYer or technician can replace it. High-level steps: 1) Power off and shut off water.2) Remove the ice bin and any shelving that blocks access. 3) Disconnect the electrical connector(s) from the old ice assembly and carefully detach any clips or retainers. 4) Remove the mounting screws and remove the old assembly; disconnect the water fill tube (some water may spill). 5) install the new assembly in reverse order: mount, reconnect water fill tube, plug in electrical connector, replace bin/shelves. 6) Turn on the water and power, then run a diagnostic or allow the unit to cycle to verify proper operation. Follow the model-specific service manual for any special clips or harness routing.
After installing the new ice maker, it’s not making ice – what should I check first?
Check these common causes: 1) Water supply is turned on and not kinked; 2) Water filter is not clogged or overdue-replace if in doubt; 3) Freezer temperature is cold enough (ideally 0°F / -18°C); 4) Water inlet valve is functioning – if the valve fails it won’t fill the mold; 5) Electrical connector to the ice assembly is fully seated; 6) The ice maker may need to be placed in a harvest/fill test mode – consult the service manual to force a fill cycle. If the fill cycle occurs but no water flows,suspect the inlet valve or blocked tubing.
Why are the ice cubes small, hollow, or misshapen after replacement?
Common causes include low water pressure or a partially clogged/old water filter (reduces fill volume), partially frozen or blocked fill tube (restricts flow), or freezer temperature being too warm during formation. Hollow cubes can also be caused by air in the water line; run several cycles after a new part or after reconnecting water to purge air. Check water pressure to the home and replace the water filter if it hasn’t been changed recently.
The ice maker is noisy or seems to run continuously - what does that mean?
Noises during harvest/fill are normal,but grinding,loud clicking,or continuous motor/humming can indicate a jammed ejector,seized motor,or failed control/harvest components. Continuous harvest (constant cycling/heater on) may indicate a bad sensor/thermostat or control board signal. Remove the ice bin and inspect for ice jams, damaged gears, or a blocked ejector. If the mechanism is physically obstructed or if motor/thermostat shows open/shorted electrical readings, replace the assembly.
how can I test the ice maker’s components electrically, and when should I replace the whole assembly?
With power removed, use a multimeter to check continuity/resistance of accessible components: motor windings, heater (if present), and any thermostats/thermistors. Many failures are mechanical (gears, motor) or involve sealed components, so if the motor has no continuity, the heater is open, or the unit has physical damage you should replace the entire assembly. If the ice maker appears OK electrically but still fails to fill, test the water inlet valve (it should show continuity and open when energized) and verify the water supply. When in doubt, replacing the OEM assembly is often faster and more reliable than repairing internal parts; keep the part number and warranty data for return/exchange.
To Conclude
The DA82-02668A (Samsung A/S Assembly ICE) and DA94-02275P (CD 120 OEM) are manufacturer-specified components that play defined roles within samsung appliance systems. As OEM assemblies, thay are engineered to meet the original equipment design, fit, and performance requirements, contributing to reliable operation, consistent functionality, and user safety in the appliances for which they are specified.
Accurate diagnosis is essential before replacing either component: identifying the underlying cause of a malfunction prevents unnecessary parts changes and reduces the risk of recurring faults.When replacement is required, using the correct OEM part number and following manufacturer installation and service procedures helps ensure compatibility, preserves system performance, and maintains any applicable warranties.
thoughtful diagnosis coupled with timely replacement using the correct OEM components supports long-term reliability and efficiency. For best outcomes, rely on established diagnostic practices and, when necessary, professional service to install and verify the DA82-02668A and DA94-02275P components.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
Recommended Products
Search by part number or model number
Use product pages, category pages, and support pages to keep the path to the correct part clear.