DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM is an OEM tubing/fitting assembly specified for certain Samsung dryer units, identified by a Lokring-style mechanical connection wiht an OD5 (5 mm outer diameter) refrigerant line interface. In practice this part is a factory-supplied tube and connector configuration used to make a pressure‑tight joint in the appliance’s sealed fluid circuit rather than a generic hose or electrical component.
within a heat‑pump or refrigeration‑based dryer the component serves as part of the sealed refrigerant plumbing that links the compressor, evaporator, condenser and associated service valves. Its primary function is to provide a reliable, leak‑resistant pathway for the working fluid while preserving system pressure and thermal transfer characteristics; it therefore directly interacts with the refrigeration circuit, mounting brackets, and any nearby temperature or pressure sensors. Proper material compatibility, joint integrity and installation method are important because leakage or restriction at this junction degrades drying performance and can create safety and regulatory issues.
In this article readers will find a technical overview of the DA81-06007A fitting/assembly including its intended function,model compatibility and the meaning of the OD5 specification; common failure symptoms to watch for (external oil/wet spots,frost patterns,rapid pressure loss,audible hissing,and reduced heat‑pump efficiency); practical troubleshooting checks and leak‑testing considerations; and replacement guidance covering compatibility checks,the differences between lokring mechanical joints and brazed connections,tooling and handling precautions,and post‑service evacuation/charging implications. The focus is on giving technicians, engineers and informed appliance owners the context needed to diagnose issues and make informed repair or replacement decisions without prescriptive step‑by‑step procedures.
Table of Contents
- Function and Role of the DA81-06007A Component in Samsung A/S Dryer Systems
- How the DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM Interfaces and Operates Within the Appliance Assembly
- Common Failure Modes, Observable Symptoms and Measurable Diagnostics for the DA81-06007A Part
- Compatibility Matrix, Replacement Considerations and Step‑by‑Step Installation and Troubleshooting Procedures for DA81-06007A OEM Units
- Q&A
- Future Outlook
Function and Role of the DA81-06007A Component in Samsung A/S Dryer Systems
The DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM is a refrigerant circuit filter-drier assembly used in Samsung heat-pump dryer systems. Its primary function is to remove moisture and particulates from the closed refrigerant loop and provide limited contaminant storage so that the expansion device and compressor remain protected. In practical terms the part houses a desiccant and a particulate filter media, is sized to match the flow characteristics of the appliance refrigerant circuit, and is fitted to 5 mm outer-diameter tubing using the Lokring connection style specified for C1220T copper lines in European service practice.
In service, the component behaves as a pressure-drop element when loaded; gradual desiccant saturation or internal clogging will increase differential pressure across the device and can reduce heat-pump performance or cause control faults. Replacement is recommended whenever the sealed refrigerant circuit is opened for repair, or if diagnostic data show abnormal pressure differentials or moisture-related symptoms. Installation requires correct alignment of the flow direction, proper Lokring installation tools for OD5 tubing, and a full system evacuation and charge after replacement to restore designed performance.
- Function: moisture adsorption and particulate filtration to protect metering and compressor components.
- Connection: Lokring-compatible for 5 mm OD (C1220T) copper/lines, matching OEM sealing practices.
- Service indicators: rising pressure drop,oil carryover,icing on evaporator,or loss of heat-pump efficiency.
- Service practice: replace when opening system; ensure correct flow orientation and perform full evacuation/recharge.
| Item | Description |
|---|---|
| Part number | DA81-06007A (OEM filter-drier assembly) |
| connection type | Lokring OD5 (for C1220T tubing) |
| Primary function | Desiccant-based moisture removal and particulate filtration in refrigerant loop |
How the DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM Interfaces and Operates Within the Appliance Assembly
The DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM is a sub‑assembly that provides the sealed line connection and mating interfaces required by the dryer’s service and production architectures. This assembly combines a mechanical mounting footprint compatible with the C1220T form factor and a fluid/junction connection that uses a Lokring OD5 cold‑weld joint to achieve a metal‑to‑metal seal. in practice the part supplies a leak‑resistant pathway for a small‑diameter tube (OD5) while also presenting the OEM electrical and bracket attachments needed to locate sensors or valves in the appliance housing without additional adapters.
Operationally, the assembly functions as both a structural mounting point and a sealed conduit; its behavior under service conditions depends on correct Lokring engagement, proper routing to avoid abrasion and heat exposure, and correct electrical mating for any integrated sensors. Technicians replacing this item should verify tube OD, inspect Lokring joints for proper compression and absence of visible gaps, and confirm electrical continuity across connectors before reassembly. Common practical checks include a pressure or soap‑bubble leak test on the Lokring joint and a multimeter continuity/resistance check across sensor leads; symptomatically, leaks or poor connector contact typically present as pressure loss, abnormal cycle behavior, or sensor fault codes.
- Key interfaces: Lokring OD5 tube joint, C1220T mounting footprint, OEM electrical connector(s)
- Typical verification steps: visual inspection, leak test, multimeter continuity, correct routing and clamping
- Compatibility note: use OEM or equivalent Lokring‑compatible fittings and matching OD5 tubing for reliable sealing
| Item | Description |
|---|---|
| Tube connection | Lokring OD5 metal‑to‑metal cold‑weld joint for small‑OD tubing |
| Mounting | C1220T footprint and OEM brackets for direct replacement |
| Primary function | Sealed fluid/gas pathway plus electrical/mounting interface within dryer assembly |
| Common tests | Leak test (pressure or soapy water), continuity/resistance check on connectors |
Common Failure Modes, Observable Symptoms and Measurable Diagnostics for the DA81-06007A Part
The DA81-06007A samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM is an OEM interconnection/connector assembly used on certain Samsung dryer service harnesses and assemblies. In service it functions as a low-impedance junction and mechanical support between the dryer control and the heating/motor circuits, designed to accept a Lokring OD5-style connection and withstand the thermal and vibration environment of the dryer cabinet. Compatibility is constrained to the wiring layout and terminal configuration of the C1220T series and similar Samsung A/S dryer assemblies; replacement requires matching the terminal layout, cable gauge, and mechanical mounting used on the original assembly to maintain rated current carrying and insulation clearances.
common failure modes include open circuits from broken conductors, increased contact resistance from corrosion or loose crimps, localized overheating or melting from overloaded circuits, and intermittent faults caused by vibration-disturbed terminations. observable symptoms are prolonged drying times, intermittent or complete loss of heating or motor operation, visible discoloration or charring at the connector, and fault codes indicating circuit interruption. Measurable diagnostics rely on basic electrical checks: continuity and resistance across the part and individual terminals, presence and correct voltage under load at the connector, insulation resistance to chassis, and temperature rise at the connector under normal operating current. Practical checks for a field technician include a wiggle test under observation, measuring voltage drop across the connector with a digital multimeter while the load is running, and comparing measured results to the expected behavior for a properly functioning junction.
- Intermittent operation or no heat
- Visible charring, melted insulation, or discoloration
- High resistance or open continuity on multimeter
- Excessive temperature rise at connector under load
| Item | Description |
|---|---|
| Continuity | Expected: closed circuit through terminals; open = broken conductor/failed termination |
| Voltage under load | Expected: line voltage present at the connector during operation with minimal voltage drop across the part |
| Temperature rise | Expected: small, steady rise; excessive heat indicates high contact resistance or overload |
compatibility Matrix, Replacement Considerations and Step‑by‑Step Installation and Troubleshooting procedures for DA81-06007A OEM Units
The DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM functions as an in‑line filter‑drier for refrigeration circuits used in select Samsung appliance assemblies.it removes moisture and solid contamination, protects the compressor from acid formation, and presents a Lokring OD5 cold‑weld interface rather than a brazed or flare connection. Compatibility is resolute by refrigerant type,tubing outer diameter,mounting orientation and maximum allowable working pressure; technicians should verify refrigerant chemistry and oil compatibility,confirm the Lokring OD5 mating geometry,and cross‑reference appliance model C1220T and associated service schematics before replacement to avoid flow restriction or sealing failures.
- Pre‑replacement checks: confirm refrigerant and oil type, measure tubing OD, inspect sight glass/pressure port locations, and verify filter‑drier flow direction and pressure rating against the service manual.
- Common failure symptoms: reduced cooling capacity, compressor short cycling, frosting on evaporator, brown/black debris in access ports or evidence of moisture in sight glass.
- Installation essentials: recover refrigerant, use the correct Lokring installation tool and new fittings (do not reuse cold‑weld joints), perform a pressure/leak test, evacuate to deep vacuum, then recharge to specified charge and monitor pressures.
| Item | Description |
|---|---|
| DA81-06007A | Filter‑drier with Lokring OD5 interface for specified Samsung assemblies; removes moisture/particles and sized for C1220T configurations. |
| Tools required | Lokring installation/removal tool,vacuum pump (target deep vacuum),manifold gauges,electronic leak detector,nitrogen bottle for pressure testing. |
| verification points | Refrigerant compatibility, tubing OD and wall thickness, service orientation, and manufacturer pressure ratings. |
Follow a controlled replacement procedure: safely recover and store the refrigerant, purge the service area with dry nitrogen when cutting or removing joints, and remove the old drier using the Lokring removal method appropriate for OD5 tubing. Install the replacement with a new Lokring sleeve and tool per Lokring specifications to ensure a factory‑grade cold weld; do not substitute brazing without validating materials and oil compatibility. After mechanical installation, perform a pressure and leak test using dry nitrogen per the appliance’s service data, then evacuate the system to a deep vacuum (typical service practice targets low micron levels), verify the absence of leaks, and recharge using the exact refrigerant charge and oil recommendations. If symptoms persist after replacement, measure pressure differential across the drier, confirm correct superheat/subcooling values, and inspect for non‑condensables or internal collapse of the line; these diagnostics help distinguish a true drier restriction from upstream or downstream system faults.
Q&A
What is part DA81-06007A (A/S DRYER;ALL C1220T EUROPE LOKRING OD5) and what does it do?
DA81-06007A is an OEM refrigerant filter‑drier assembly used on certain Samsung refrigeration/heat‑pump appliance circuits. Its purpose is to remove moisture, acids and particulate contamination from the refrigerant and to protect the expansion device and compressor from blockages and corrosion.
Which Samsung models or systems is this dryer compatible with?
This is a factory (OEM) replacement specified for certain European Samsung appliances. Compatibility is determined by the appliance model and the service parts list: always confirm the DA81‑06007A part number against your appliance model/serial number or the official Samsung parts catalog before ordering or installing.
How do I identify the dryer on the appliance and what does “LOKRING OD5” mean?
The dryer is typically a small cylindrical canister in the refrigerant line between the condenser and the expansion device; it usually has an inlet/outlet and a flow arrow stamped on it. “LOKRING OD5” indicates the unit is fitted for Lokring mechanical tube connections sized to the listed OD series – verify the exact tubing outer diameter on the parts sheet or product spec before installing to ensure the correct sleeve and tool are used.
Can I replace this dryer myself at home?
Replacement requires access to the sealed refrigerant circuit and pressurized refrigerant handling, so it should be performed by a licensed HVAC/R technician. Proper replacement requires recovering refrigerant, making a leak‑tight Lokring connection (or brazing if specified), evacuating the system, and recharging to the correct refrigerant charge and oil specifications.
What tools and materials are required to install a Lokring OD5 version of this dryer?
Installation typically requires the correct size Lokring sleeves and a Lokring pressing tool rated for the OD5 series, a vacuum pump and micron gauge for evacuation, nitrogen for pressure/leak testing, a refrigerant recovery machine, and appropriate personal protective equipment.If the service procedure calls for brazing rather of Lokring, an appropriate brazing torch and flux must be used instead (follow manufacturer instructions).
Does the dryer have a required flow direction or orientation?
Yes – most filter‑driers have a flow arrow and must be installed in the correct direction (from condenser/liquid line toward the expansion device). Install them per the arrow and manufacturer recommendations; some filter‑driers also have preferred orientation (vertical, inlet up/down) noted on the part sheet, so follow the service documentation for the specific part.
When should the dryer be replaced?
Replace the filter‑drier whenever the sealed system is opened for repairs (compressor change, major line work) or if contamination, moisture, or acid is suspected. Symptoms that can indicate a clogged or compromised drier include reduced cooling performance, abnormal pressures, or evidence of system contamination after a failure.
How should I test the system for leaks and proper operation after replacing the dryer?
After installation, a technician should pressure‑test the line with dry nitrogen to check for leaks, perform a vacuum to remove non‑condensables and moisture (to service‑level vacuum), conduct a hold test to ensure no leak or moisture ingress, and then recharge the system with the correct refrigerant/oil per Samsung specifications.Finally verify normal operating pressures, temperatures and appliance function before returning the appliance to service.
Future Outlook
The DA81-06007A Samsung A/S DRYER;ALL C1220T EUROPE LOKRING OD5. OEM is an OEM replacement component intended to restore or maintain proper operation in compatible Samsung systems.As an original equipment part, it is manufactured to fit specified assemblies and to meet the tolerances and material standards expected by the original designer. Correct selection of this part helps maintain system performance, reliability, and compatibility with other components.
Accurate diagnosis is essential before replacing the DA81-06007A; replacing parts without confirming the root cause can lead to needless expense and may not resolve the underlying issue. When replacement is required, using the correct OEM part and following manufacturer-recommended installation procedures helps ensure a safe, reliable repair. Professional technicians should confirm compatibility,inspect adjoining components,verify connections (including Lokring fittings where applicable),and perform post-repair testing to confirm system integrity and performance.
the DA81-06007A OEM dryer component plays a specific role in maintaining the intended function of compatible Samsung equipment. proper diagnosis, selection of the correct OEM replacement, and competent installation are key to restoring reliable operation, preserving equipment longevity, and ensuring safe performance.
Professional Appliance Service
If your appliance requires professional diagnosis or repair, visit
Revolff Home Services
for expert appliance repair services.
For local appliance service information see
Dryer repair Henderson
.
Replacement parts for many appliance models can also be found at
Reliable-Parts-Hub
.
