The WH49X27325 GE Kit Agitator 27 and Bolt OEM is a factory-specified replacement assembly engineered to restore the agitator function in compatible GE top‑load washing machines.As the mechanical interface that transfers rotational and oscillatory motion from the drive mechanism into the wash basket, the agitator is critical for soil removal, load balancing and overall wash performance. When wear, breakage or degraded engagement occurs, replacing the agitator with a correctly matched OEM kit is essential to maintain machine efficiency and longevity.
This article examines the WH49X27325 kit from a technical perspective: its role in the drivetrain, the design considerations that govern fit and function, and the expected performance advantages of using an OEM assembly versus aftermarket substitutes. We will review compatibility indicators and identification steps to ensure correct part selection, outline the basic service sequence for removal and installation, and highlight common failure modes and diagnostic checks that inform replacement decisions.
Intended for service technicians and technically proficient DIY users, the discussion emphasizes serviceability, installation best practices and the operational tolerances that influence long‑term reliability. By focusing on engineering intent and practical implementation, the article provides the data required to evaluate, select and install the WH49X27325 agitator kit with confidence.
The WH49X27325 OEM kit includes a full 27-inch agitator assembly and the matching mounting bolt, manufactured to the original GE specifications so the spline profile and mounting flange line up with factory components. The agitator body is molded from reinforced thermoplastic to resist abrasion from heavy loads and common detergents, while the bolt is zinc-plated steel to resist corrosion; this combination reduces the chance of premature failure. Compatibility covers a range of GE top-load washers that use a 27″ agitator configuration, but fitment can vary by production date and transmission style-so always verify your washer model number and parts diagram before ordering. Local service technicians who perform multiple appliance types can usually confirm fitment on-site; for example, teams that advertise Dryer repair Henderson often inspect washer drivetrain components and can advise whether the WH49X27325 is the correct replacement.
| Item | Description |
|---|---|
| Agitator length | 27 inches,factory profile for compatible GE top-load models |
| Material | Reinforced thermoplastic agitator,zinc-plated steel bolt |
| fitment tip | Match your machine’s model tag and transmission spline count before purchase |
- Required tools: 1/2″ socket or wrench for the bolt,long-handled ratchet,protective gloves,and a service manual or exploded parts diagram for reference.
- Installation essentials: remove the fabric softener dispenser (if present), lift out the old agitator by removing the bolt and any retaining clip, inspect the splined shaft for wear, then seat the new agitator fully on the splines before tightening the bolt.
- Maintenance and inspection: check for cracked fins, worn splines, or loose bolts every 6-12 months; noisy operation, excessive vibration, or clothes getting caught are common signs the agitator needs attention.
- Troubleshooting tips: if the agitator feels loose after installation, recheck seating and ensure the bolt is snug-avoid excessive torque which can strip plastic splines; if agitation is inconsistent, inspect the agitator dogs or cogs (if applicable) and the transmission coupling.
During installation, work methodically: document bolt positions, keep fasteners in a small container, and run a short/agitate-only test cycle after reassembly to confirm correct operation. If you encounter stripped splines or a damaged shaft, replacement of the transmission coupling or professional service may be required rather than just replacing the agitator; in manny cases a technician can diagnose whether a simple parts swap will restore reliable service. For parts, advice, or on-site fitting services, consider professional appliance repair providers who can both supply the WH49X27325 kit and perform a proper installation to factory standards.
WH49X27325 GE KIT AGITATOR 27 AND BOLT OEM appliance repair available
Reliable-Parts-Hub
Q&A
Q: What is the WH49X27325 GE Kit Agitator 27 and Bolt OEM?
A: The WH49X27325 kit is an OEM agitator assembly and fastener supplied for compatible top-load washing machines. It includes the agitator body (upper/lower as applicable) and the mounting bolt required to secure the agitator to the transmission/agitator shaft. As an OEM kit, it is manufactured to the original equipment specifications for fit, materials, and spline geometry.
Q: How do I confirm that WH49X27325 fits my washer?
A: Verify fitment using the appliance model number (found on the washer cabinet, inside the door/frame, or on the back panel). Cross-reference that model number with the OEM parts catalog or an authorized parts distributor. Confirm the following before purchase/installation:
- Manufacturer and model number match an OEM parts list that lists WH49X27325.
- The agitator spline count/profile and shaft type match your washer’s transmission shaft.
- The physical dimensions and mounting configuration of the kit are consistent with the removed component.
Q: What components are included in this OEM kit?
A: Typical contents include:
- Agitator (upper and/or lower section depending on part configuration)
- mounting bolt specifically sized for the agitator shaft
- Any necessary seal, spacer, or washer if specified by the OEM
Check the kit contents list from the supplier to confirm what’s included for WH49X27325.
Q: What tools are required to install this agitator kit?
A: common tools:
- Socket set (sizes vary; a 9/16″ or appropriate metric equivalent socket is commonly used for agitator bolts-verify for your model)
- Ratchet or breaker bar
- Torque wrench (recommended for final bolt tightening)
- Flat-head screwdriver or trim tool (to remove caps or dispensers)
- Pliers (for retaining clips or pull tabs)
- Safety gloves and eye protection
Always confirm the required socket size and any special tools in the service manual for your washer model.
Q: What are the recommended safety precautions before starting installation?
A: Safety checklist:
- Unplug the washer or disconnect power at the breaker.
- turn off water supply valves if you need to move the washer or remove hoses.
- Work on a stable, level surface and keep children/pets away.
- Use proper lifting techniques – agitators may be heavy or awkward.
- Consult the service manual for model-specific safety steps.
Q: What are the general steps to replace the agitator with WH49X27325?
A: General installation sequence (model-specific details may vary):
- Disconnect power.
- Open the washer lid and remove the fabric softener dispenser/cap if present.
- Pry off the decorative cap covering the agitator bolt (if applicable).
- Use the appropriate socket to remove the agitator mounting bolt.
- Pull the old agitator straight up; use a rag or block and pry evenly if it is stuck.
- Inspect the shaft splines,drive dogs,and seals; replace any worn parts.
- Position the new agitator onto the shaft, aligning splines and drive features.
- Install the OEM bolt and tighten per the service manual torque specification.
- Replace caps and any removed trim pieces.
- Restore power and run a short cycle to verify proper operation (no wobble, noise, or leaks).
Q: How tight should the agitator bolt be torqued?
A: Tighten the bolt to the torque specified in the washer’s service manual. If the manual is unavailable, use a calibrated torque wrench and tighten until the bolt is secure enough to prevent wobble but avoid over-torquing which can strip splines or damage the shaft. If in doubt, consult an authorized service technician or the OEM service documentation for the exact torque value.
Q: What common problems occur after installing a replacement agitator, and how do I troubleshoot them?
A: Common issues and checks:
- Wobble or misalignment: Verify the agitator is fully seated on the splines and the mounting bolt is properly tightened.
- Loud noise or clunking: Check for worn drive dogs, damaged splines, loose bolt, or foreign objects between agitator sections.
- No agitation: Ensure the bolt is installed and tightened, inspect transmission coupling/dog assembly, and confirm drive motor is functioning.
- Leaks: Inspect nearby seals and the tub for damage; ensure no components were dislodged during installation.
If problems persist, revert to service manual diagnostics or contact OEM support.
Q: Is this an OEM part or an aftermarket replacement? What are the advantages?
A: WH49X27325 is referenced as an OEM kit for compatible GE/brand washers. OEM parts offer:
- Exact fit and compatibility with original specifications
- Consistent materials and manufacturing tolerances
- typically easier installation and fewer fitment issues
Aftermarket parts may be suitable in some cases, but confirm spline geometry and dimensions to avoid improper fit.
Q: Can I reuse the existing bolt when installing a new agitator?
A: The OEM kit normally includes a new bolt. it is best practice to use the supplied OEM bolt to ensure correct length, thread engagement, and clamping force. Reusing an old bolt that is stretched, corroded, or damaged can lead to failure or improper assembly.
Q: How long does installation usually take for a qualified technician?
A: For a trained technician with the right tools and parts on hand,typical replacement takes approximately 20-45 minutes depending on model complexity and any ancillary repairs needed (e.g., replacing drive dogs or seals). For a DIYer allow extra time for preparation and verification.
Q: Are there maintenance tips to extend the life of the agitator and associated components?
A: Maintenance recommendations:
- Avoid overloading the washer; excessive load increases strain on agitator and transmission.
- Clean the agitator and tub periodically to remove debris and residue.
- Inspect drive dogs, splines, and seals during service intervals for wear.
- Use appropriate detergents and follow manufacturer load recommendations to reduce mechanical stress.
Q: what warranty or return policy applies to this OEM kit?
A: Warranty terms vary by seller and OEM. OEM kits typically carry a limited parts warranty against manufacturing defects; duration and coverage details should be confirmed with the vendor or OEM.Retain proof of purchase and verify return/return authorization procedures prior to installation.
Q: Where can I purchase WH49X27325 and how do I ensure authenticity?
A: purchase from authorized OEM dealers, reputable appliance parts distributors, or the manufacturer’s official parts store. To ensure authenticity:
- Buy from sellers with verified OEM sourcing and positive reviews.
- Confirm the part number and inspect packaging and part markings on delivery.
- Request original OEM documentation or warranty paperwork.
If you would like, I can draft model-specific installation steps or check common compatible models if you provide your washer’s full model number.
Insights and Conclusions
the WH49X27325 GE Kit (Agitator 27 and Bolt OEM) restores the intended agitation geometry and fastening integrity of compatible GE washers by supplying a factory-matched agitator and the correct bolt for secure installation. As this is an OEM assembly, it maintains original fit, function, and material tolerances-minimizing the risk of premature wear or performance degradation that can result from non‑OEM substitutes.
For reliable results, follow the OEM installation procedure and torque specifications in the service manual, verify proper alignment of the agitator spline and clutch components, and inspect mating parts (drive cam, transmission interface, and seals) for wear prior to final assembly. after installation, run a diagnostic or short wash cycle to confirm smooth operation and absence of unusual noise or vibration.
When replacing agitation components, use genuine WH49X27325 kits to preserve warranty coverage and serviceability; consult model compatibility charts or contact authorized support if there is any uncertainty about fitment. For procurement,warranty details,or technical assistance,refer to the manufacturer’s parts department or an authorized parts distributor.
End of article.